2014 LAS VEGAS INTERNATIONAL INDOOR CHAMPIONSHIPS "IIC" PRESENTED BY SCOTTY ERNST
#286
Super Moderator
iTrader: (81)
Amateur Class Handout Motor Announcement
For the 10th Anniversary of the International Indoor Championships we are proud to announce the Amateur class will be using the brand new ORCA RX3 motors!
The RX3 motor was developed from the knowledge gained from the RX2 and TX series of motors.
The RX3 motor features
High efficiency stator design
Large 11x5mm front bearing
High quality NMB bearings featuring high carbon chromium steel and deep groove ring
Angle cut vent holes for thermal efficiency
High quality and easy to solder copper wire tab
2 piece motor housing
Higher position sensor connector to keep wire off the ground
New 12.4mm spec rotor for wide power band
Magnetically balanced rotor
All aluminum can and timing ring design
Infintely adjustable timing ring
The RX3 motor was developed from the knowledge gained from the RX2 and TX series of motors.
The RX3 motor features
High efficiency stator design
Large 11x5mm front bearing
High quality NMB bearings featuring high carbon chromium steel and deep groove ring
Angle cut vent holes for thermal efficiency
High quality and easy to solder copper wire tab
2 piece motor housing
Higher position sensor connector to keep wire off the ground
New 12.4mm spec rotor for wide power band
Magnetically balanced rotor
All aluminum can and timing ring design
Infintely adjustable timing ring
#287
Tech Adept
For the 10th Anniversary of the International Indoor Championships we are proud to announce the Amateur class will be using the brand new ORCA RX3 motors!
The RX3 motor was developed from the knowledge gained from the RX2 and TX series of motors.
The RX3 motor features
High efficiency stator design
Large 11x5mm front bearing
High quality NMB bearings featuring high carbon chromium steel and deep groove ring
Angle cut vent holes for thermal efficiency
High quality and easy to solder copper wire tab
2 piece motor housing
Higher position sensor connector to keep wire off the ground
New 12.4mm spec rotor for wide power band
Magnetically balanced rotor
All aluminum can and timing ring design
Infintely adjustable timing ring
The RX3 motor was developed from the knowledge gained from the RX2 and TX series of motors.
The RX3 motor features
High efficiency stator design
Large 11x5mm front bearing
High quality NMB bearings featuring high carbon chromium steel and deep groove ring
Angle cut vent holes for thermal efficiency
High quality and easy to solder copper wire tab
2 piece motor housing
Higher position sensor connector to keep wire off the ground
New 12.4mm spec rotor for wide power band
Magnetically balanced rotor
All aluminum can and timing ring design
Infintely adjustable timing ring
#289
#297
Team EAM
iTrader: (79)
It should also only be allowed for speedo's that do not have built in boosters. Its been found that a few will feed voltage to the motor if you use the built in booster and the receiver pack. Some speedo's do NOT have a built in booster in 1S.
EA
Last edited by EAMotorsports; 09-19-2014 at 11:05 AM.
#299
Team EAM
iTrader: (79)
Easy way to tell if its bleeding is to unplug your 1S battery and turn on the receiver pack and car. If the motor will run with no 1S in it then its bleeding voltage from the receiver pack.
Granted its not much but in Oval racing every little bit helps they say. In their testing in oval it was good for half a lap in a 4 minute run. At a large race thats the differece in TQ to the E main
EA
#300
Moderator
iTrader: (9)
Join Date: Jan 2004
Location: Outside doing things in places... Denver, CO
Posts: 4,609
Trader Rating: 9 (100%+)
I think you worded that wrong, I think you meant it should only be allowed for speedos that do not have built in boosters. You say it both ways in that post.