Novak Smart Tray
#16
Originally Posted by axel
not even fully on, i was about to place the bottom two and they were half way on, then i pulled it out immediatlet after i saw the spark , let's just say my hands were on them the whole time during this incident.
So you think there was damage?
So you think there was damage?
#17
Originally Posted by axel
Novak recommend not using the dead short feature? , why not??
also any replies to my previous question would be Greatly appreciated.
also any replies to my previous question would be Greatly appreciated.
#18
Originally Posted by dakrat
i dont think u damage that cells, if u did, its very minimal. mine was worst, the solder melted and cells got seprated from the pack. u should be fine
#19
Tech Master
Originally Posted by axel
Novak recommend not using the dead short feature? , why not??
#20
Do you guys store your packs after traying them down to .9v? And before my heat should i tray them down to .1v then charge them? How does this plan sound for stock racing?
#21
Originally Posted by axel
Do you guys store your packs after traying them down to .9v? And before my heat should i tray them down to .1v then charge them? How does this plan sound for stock racing?
#22
Help !!!!! my pmr cells now charge peak at 3330mah??!! they used to charge to 3800mah?!! well this might have been do to that i trayed them down to .9v for the first time...but still 3330!!?? maybe i should've trayed down to .1v or deadshort them to get max. mah...is this permanet?!!!
#23
Tech Master
Originally Posted by axel
Help !!!!! my pmr cells now charge peak at 3330mah??!! they used to charge to 3800mah?!! well this might have been do to that i trayed them down to .9v for the first time...but still 3330!!?? maybe i should've trayed down to .1v or deadshort them to get max. mah...is this permanet?!!!
#24
Originally Posted by axel
Help !!!!! my pmr cells now charge peak at 3330mah??!! they used to charge to 3800mah?!! well this might have been do to that i trayed them down to .9v for the first time...but still 3330!!?? maybe i should've trayed down to .1v or deadshort them to get max. mah...is this permanet?!!!
#25
what will then?? this really sucks if my cells stay like this
#26
Originally Posted by centax error!
post charge settings?
disch:10amps ( i know weak)
peak sensitivty: 5mv/c
dsch. volt.: 0.9v/c
then i trayed them to .9v,
first time they chraged at 3700 range then later to 3338!!
I have a duratrax ice
#27
Help??? i think i might have permantly damaged my cells...but how this tray do that?
#28
Tech Master
Originally Posted by axel
ch: 5amps
disch:10amps ( i know weak)
peak sensitivty: 5mv/c
dsch. volt.: 0.9v/c
then i trayed them to .9v,
first time they chraged at 3700 range then later to 3338!!
I have a duratrax ice
disch:10amps ( i know weak)
peak sensitivty: 5mv/c
dsch. volt.: 0.9v/c
then i trayed them to .9v,
first time they chraged at 3700 range then later to 3338!!
I have a duratrax ice
#29
well i'm worried becuase this was all within 2 consecutive cycles...i worry alot about mah beacuse it shows me how much longer i can use these cells...i cycled them 2 times today and 2 times yesterday...i hope your right about having them needing rest.
#30
Tech Master
don't cycle your packs if you don't really have to. Again don't be confused with MAH and actual runtime. It's the run time that you should worry about. I charged all my packs maximum of two times per day and my good packs only ones.