F201
#571
With the 23T motors for the nats, the F201 will be a flying rocket! Has anyone had experience with this motor in the F201?
#572
We race F201's with 19T motors and they are pretty fast. Lot's of fun to drive, but they push quite a bit more with the higher speeds. You'll need to adjust your turn in point accordingly.
#573
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
Tower hobby has some Tamiya foam tires "made for the F1 cars" that will need to be glued on, can there is used for the 201?
#574
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
Official Tamiya response was nope, don't make them for F201
as of now...
as of now...
#575
That would be cool if an after market company made foams. The would be amazing to drive!
#577
Originally posted by rc-zombies
The car would no longer be that scale look that most F1 racers are after.
The car would no longer be that scale look that most F1 racers are after.
#578
Hey Neil, shouldn't you be PB'ing for Serpent right about now? hmm Serpent...Spearmint Rhino! Make sure you take the boys over there if they have time haha.
It would be cool if an aftermarket company made ribbed foamies for the f201...that'd be cool for all of the rug rats.
It would be cool if an aftermarket company made ribbed foamies for the f201...that'd be cool for all of the rug rats.
#579
You mean grooved. Hey Rod thanks for the help on the review!
#580
gtypecanare,
Ready to rumble with F201 this Sat?
Steve Wang
Ready to rumble with F201 this Sat?
Steve Wang
#581
Yup, I'm ready, but I might be testing a 23T motor on the high speed gear set to see how the brush and comm. comes out. But I'll be ready to go back to Monster Horespower motor. Other than no changes to the setup.
#582
Originally posted by rtypec
Hey Neil, shouldn't you be PB'ing for Serpent right about now? hmm Serpent...Spearmint Rhino! Make sure you take the boys over there if they have time haha.
Hey Neil, shouldn't you be PB'ing for Serpent right about now? hmm Serpent...Spearmint Rhino! Make sure you take the boys over there if they have time haha.
#583
gtypecanare,
I'll be testing more setups on Sat. (I'm gonna throw that fiber glass plate back on... hehehehe) I'll be doing the stock motor trim tomorrow, I figure I can start testing the 23T around beginning of Sept.
See you tomorrow
Steve Wang
I'll be testing more setups on Sat. (I'm gonna throw that fiber glass plate back on... hehehehe) I'll be doing the stock motor trim tomorrow, I figure I can start testing the 23T around beginning of Sept.
See you tomorrow
Steve Wang
#584
Hey Steve,
Sounds good, I'll have a Monster motor fresh to run. I just wanna see how the 23T motor does with the speed-tuned gears and stock gears. Kinda weird science stuff for the morning. Looks like we'll have another beautiful day tomm. for testing and learning . To all the F201 racers in Washington state, good luck!
Sounds good, I'll have a Monster motor fresh to run. I just wanna see how the 23T motor does with the speed-tuned gears and stock gears. Kinda weird science stuff for the morning. Looks like we'll have another beautiful day tomm. for testing and learning . To all the F201 racers in Washington state, good luck!
#585
Tech Apprentice
Tamiya will be releasing a reinforced lower suspension arm for the F201 in late September.
http://www.formula1-rc.com/News/News.asp?ID=232
http://www.formula1-rc.com/News/News.asp?ID=232