spintec I.C.C charger
#1141
Tech Adept
I have the manual, but can't find it on the website.
The resistor goes from the lower contact to the upper contact of your 6th cell. And the 3rd alligator clip goes to the upper 5th cell itself. You can connect it to the contact pin but that way it's less accurate, so clip it to the negative pole on the 5th cell.
Be sure to have version 1.06c or higher!
The resistor goes from the lower contact to the upper contact of your 6th cell. And the 3rd alligator clip goes to the upper 5th cell itself. You can connect it to the contact pin but that way it's less accurate, so clip it to the negative pole on the 5th cell.
Be sure to have version 1.06c or higher!
#1142
Tech Initiate
Originally Posted by Smartypants
It is a Y cable (two crocodile clips on one end and one on the other end), the two clips go on to the sixth cells probes in the bottom right corner on the ICC and the other end connects onto the end of the fifth cell as their are no probes there.....
This cable came included with my ICC that i have recently purchased in the UK.
Hope that makes sense
This cable came included with my ICC that i have recently purchased in the UK.
Hope that makes sense
But is a linear wires or there are electronics components between the two crocodiles? I say this because the pictures of the Y cables sold by spintec is strange.
Do you think I can made in my home the cable?
Can you send me a picture of installation or a wiring design? I've a doubt....
(Sorry for my bad english... i'm italian and in Italy I speak italian language )
#1143
delta peak cut off
Originally Posted by speedfreakUK
racinggear - My Spintec now always peaks on delta rather than temperature but you have to make sure you have all of your settings 100% spot on.
A couple of ideas that you can check - Check your minimum temperature setting. If this is too high as per my previous the cells will not even think about delta peak until they hit this temperature. - Check your maximum temperature from the reports and experiance it needs to be somewhere around the 50 deg C mark - Make sure your delta peak is not set too high a lot of people are moving to sub 3Mv peak ( generally 1-2Mv )
The batts in the tray will always get hotter than on a conventional charger as they do not have the airflow around them, they are encased in the charger. This was always the theory behind those stalks that you rest your batt in on the orion advantage. Ths is wh a lto of peole have taken to using half of the Much more batt cooler (v1) or integy version to create some air flow and help remove heat from above the cells ( not blowing on the cells ). This seems to help the most and ensures a pretty acurate and even temperature across the pack throughout the charge.
Hope this is of some help
A couple of ideas that you can check - Check your minimum temperature setting. If this is too high as per my previous the cells will not even think about delta peak until they hit this temperature. - Check your maximum temperature from the reports and experiance it needs to be somewhere around the 50 deg C mark - Make sure your delta peak is not set too high a lot of people are moving to sub 3Mv peak ( generally 1-2Mv )
The batts in the tray will always get hotter than on a conventional charger as they do not have the airflow around them, they are encased in the charger. This was always the theory behind those stalks that you rest your batt in on the orion advantage. Ths is wh a lto of peole have taken to using half of the Much more batt cooler (v1) or integy version to create some air flow and help remove heat from above the cells ( not blowing on the cells ). This seems to help the most and ensures a pretty acurate and even temperature across the pack throughout the charge.
Hope this is of some help
How did you get your charger to cut off at delta peak with a min temp lock out of 35c?
Thanks
Tony
#1144
Tech Adept
Originally Posted by unico2003
Do you think I can made in my home the cable?
Have you tried asking Eric by e-mailing him directly?
#1145
Tech Initiate
Delta Peak
Tony,
I have cheated a little !! Sorry !!!
Following my original queries I have an unoffical update to my charger that allows the min temp lockout to be adjusted so mine is set a little lower than 35 deg.
I have been assured by Erik that this will form part of the next firmware update released
Regards
Andy
I have cheated a little !! Sorry !!!
Following my original queries I have an unoffical update to my charger that allows the min temp lockout to be adjusted so mine is set a little lower than 35 deg.
I have been assured by Erik that this will form part of the next firmware update released
Regards
Andy
#1146
Tech Master
Any idea when the next update will be? its been a good 3 months now?
#1147
#1148
Tech Adept
Originally Posted by rcnewb2004
Any idea when the next update will be? its been a good 3 months now?
Don't know when it will be released.
Rob Janssen.
#1149
Tech Master
Could we get a "sneak preview" of what the next update holds? i am very VERY curious!
#1150
Tech Initiate
Originally Posted by vassago
I _think_ there is a resistor between the 2 clips connecting the + and - of the 6th cell and a wire between cell 5 and 6. I can measure it when I get home.
Ciao
#1151
Tech Rookie
Repeak
Can anyone please describe what does exactly Repeak functionality mean? what if this is disabled? There is no single word on this in user guide.
#1152
Tech Initiate
5 cells wiring
Originally Posted by unico2003
Can you send me a picture of installation or a wiring design? I've a doubt....
This is my doubt.. (I have not manual of upgrade for 5cells!)
The connection is C---> B or C--->A ?
(no doubt for C--->D, i thinks!)
(see link below)
wires_5cell.jpg
Thanks
#1154
Tech Initiate
Originally Posted by aston
...
Thanks a lot... you are great!
Ciao
#1155
Tech Rookie
I picked up a spintec ICC on line, but I am having a small problem with getting contact on the number 1 cell. I keep getting an error message that I am missing contract on cell 1+. I have cleaned the contacts, moved the cell around and have made sure that the two contact wires are on the +button.
Ant help and or suggestions would be welcome.
Thanks
Ant help and or suggestions would be welcome.
Thanks