Kyosho Touring Car
#1606
Tech Master
iTrader: (12)
Holy Crap!!!!!
What do we have here??????
This thread has actually been on the main page for like 3 days now!!!!
Has anybody heard from Steve @ Speedtech when he thinks the Shin Edition or the conversion will be in the USA?? Glad to see you guys suing this thread again. BTW--Where O Where is Mr. Matt ????
Brant
What do we have here??????
This thread has actually been on the main page for like 3 days now!!!!
Has anybody heard from Steve @ Speedtech when he thinks the Shin Edition or the conversion will be in the USA?? Glad to see you guys suing this thread again. BTW--Where O Where is Mr. Matt ????
Brant
#1609
Tech Initiate
Kyosho parts
A few weeks ago à turned from Xray to Kyosho, and I realised how difficult it's to find stallion parts.
For me the best ways are :
1 - rcchamp ([email protected]) (they made special order to Kyosho for me)
2 - www.speedtechrc.com (don't have all the part number, but they are serious)
3 - www.rc-direct.co.uk (didn't try but have some shin editions parts)
4 - www.tqracing.se (didn't try but have some shin editions parts)
Never order to Racing11 (http://www.racing11.net/) I never recieved my parts, and had to require a refund.
For me the best ways are :
1 - rcchamp ([email protected]) (they made special order to Kyosho for me)
2 - www.speedtechrc.com (don't have all the part number, but they are serious)
3 - www.rc-direct.co.uk (didn't try but have some shin editions parts)
4 - www.tqracing.se (didn't try but have some shin editions parts)
Never order to Racing11 (http://www.racing11.net/) I never recieved my parts, and had to require a refund.
#1610
I picked up a stallion today. Can some post a asphalt rubber tire setup for me.
Thanks,
Joe
Thanks,
Joe
#1611
Pook ~ Have you tried here yet?http://www.horizonhobby.com/Products...rodID=LOSK0256
Its just a bit hard to stay on board when the Capt. and crew start jumping ship! LOL
Brant
#1612
maxey sent you a pm with a setup
#1614
#1615
Guys here is Derek Furantani setup for High bite to medium bite asphalt...Great starting point , and pretty sure it will work for the shin car. I have used this setup for stock, and 19 turn brushless...
Front of Car
Spool or One way with AA diffs
Front block CCin , 2 mm spacer in front hidge pin, #3 spacer underneath blk
Rear block CCin , 1 mm spacer in rear hidge pin, #3 spacer underneath blk
Droop 5 with yokomo gauge
Camber 1.5 to 2 degree camber you choose, toe 0 to .5
Stock 3 hole pistons, 45wt kyosho oil, blue kyosho spring(I use Tamiya gray)
2 mm spacer in Front top camberlink, use the back camber link hole
Shock position 2nd hole from bottom
Rear of Car
Front block BBin, 2 mm spacer in front hidge pin, #3 spacer underneath blk
Rear block DD out, 1 mm spacer in rear hidge pin, #3 spacer underneath blk
Droop 4 with yokomo gauge
Camber 2 ( I look at ware of tire, I usely use 1 degree)
1 mm spacer in rear top camberlink in far back hole
stock 3 hole pistons, 40wt kyosho oil, orange kyosho spring(I use tamiya blue)
Total 3 degree toe
Shock position in middle of shock tower
AA rear diffs
We use Mazda 6 or Mazda speed 6 bodies
Tires RP30 out door or Sorex 36 with yokomo thin insert at Socal
Hopefully this will be a good starting point and I did not forget anything..
Front of Car
Spool or One way with AA diffs
Front block CCin , 2 mm spacer in front hidge pin, #3 spacer underneath blk
Rear block CCin , 1 mm spacer in rear hidge pin, #3 spacer underneath blk
Droop 5 with yokomo gauge
Camber 1.5 to 2 degree camber you choose, toe 0 to .5
Stock 3 hole pistons, 45wt kyosho oil, blue kyosho spring(I use Tamiya gray)
2 mm spacer in Front top camberlink, use the back camber link hole
Shock position 2nd hole from bottom
Rear of Car
Front block BBin, 2 mm spacer in front hidge pin, #3 spacer underneath blk
Rear block DD out, 1 mm spacer in rear hidge pin, #3 spacer underneath blk
Droop 4 with yokomo gauge
Camber 2 ( I look at ware of tire, I usely use 1 degree)
1 mm spacer in rear top camberlink in far back hole
stock 3 hole pistons, 40wt kyosho oil, orange kyosho spring(I use tamiya blue)
Total 3 degree toe
Shock position in middle of shock tower
AA rear diffs
We use Mazda 6 or Mazda speed 6 bodies
Tires RP30 out door or Sorex 36 with yokomo thin insert at Socal
Hopefully this will be a good starting point and I did not forget anything..
Last edited by King of B Main; 11-02-2007 at 08:13 AM.
#1616
All I have is Kyosho 400wt oil is there any other manufactures oil I could use that is close to 45wt kyosho oil. I have X-ray, AE, Losi.
Miny thanks,
Joe
Miny thanks,
Joe
#1618
#1619
Tech Addict
http://www.petitrc.com/view_news.php?id=4622
#1620
Thanks,
Joe Maxey