Xray T4 '13
#557
Tech Apprentice
#558
Tech Apprentice
Re
Here is Andrews setup from the IIC..
Body: PF Mazdaspeed 6
Tires: Jaco blue's
Compound: Jack 2
Weight: 1397g
Front:
2nd hole from top on shock tower
2.7 Xray spring
300cst oil
4X1.1mm pistons
1.4 Xray bar(short endlinks)
2.25 degrees camber L/R
6 degree caster blocks
1 degree toe-out
1mm spacer in front/rear of arm
Upper links middle hole on bulkhead
2mm under outer link
2mm under inner link
middle roll center blocks
2mm droop(measuring above ride height)
1.5mm Akerman
1mm bumpsteer
stock servo tie-rod position(upper position on servo saver)
Stock track width(1.5mm spacers)
Stock wheel hex with .5mm shim on each side
Xray diff using Plato as filler
52mm ECS shafts
Rear:
2nd hole from top on shock tower
2.4/2.6 Xray progressive spring
300cst oil
4X1.1mm pistons
1.2 Xray bar(short endlinks and middle position on arm)
2.75 degrees camber L/R
2.75est degrees toe-in(using .5mm shim at the rear instead of stock .7mm)
1mm spacer in front of the rear arm(2mm behind)
Upper links middle hole on bulkhead
4.5mm under outer link
2mm under inner link
high roll center blocks(+.75)
2.5mm droop(measuring above ride height)
Stock track width
Stock wheel hex
Xray diff w/2000cst
50mm stock shafts
Notes:
All screws in upper deck
15 grams of weight under steering rack
Body: PF Mazdaspeed 6
Tires: Jaco blue's
Compound: Jack 2
Weight: 1397g
Front:
2nd hole from top on shock tower
2.7 Xray spring
300cst oil
4X1.1mm pistons
1.4 Xray bar(short endlinks)
2.25 degrees camber L/R
6 degree caster blocks
1 degree toe-out
1mm spacer in front/rear of arm
Upper links middle hole on bulkhead
2mm under outer link
2mm under inner link
middle roll center blocks
2mm droop(measuring above ride height)
1.5mm Akerman
1mm bumpsteer
stock servo tie-rod position(upper position on servo saver)
Stock track width(1.5mm spacers)
Stock wheel hex with .5mm shim on each side
Xray diff using Plato as filler
52mm ECS shafts
Rear:
2nd hole from top on shock tower
2.4/2.6 Xray progressive spring
300cst oil
4X1.1mm pistons
1.2 Xray bar(short endlinks and middle position on arm)
2.75 degrees camber L/R
2.75est degrees toe-in(using .5mm shim at the rear instead of stock .7mm)
1mm spacer in front of the rear arm(2mm behind)
Upper links middle hole on bulkhead
4.5mm under outer link
2mm under inner link
high roll center blocks(+.75)
2.5mm droop(measuring above ride height)
Stock track width
Stock wheel hex
Xray diff w/2000cst
50mm stock shafts
Notes:
All screws in upper deck
15 grams of weight under steering rack
Last edited by CoreyW.; 10-10-2012 at 10:36 AM.
#559
Here is Andrews setup from the IIC..
Body: PF Mazdaspeed 6
Tires: Jaco blue's
Compound: Jack 2
Weight: 1397g
Front:
2nd hole from top on shock tower
2.7 Xray spring
300cst oil
4X1.1mm pistons
1.4 Xray bar(short endlinks)
2.25 degrees camber L/R
6 degree caster blocks
1 degree toe-out
1mm spacer in front/rear of arm
Upper links middle hole on bulkhead
2mm under outer link
2mm under inner link
middle roll center blocks
2mm droop(measuring above ride height)
1.5mm Akerman
1mm bumpsteer
stock servo tie-rod position(upper position on servo saver)
Stock track width(1.5mm spacers)
Stock wheel hex with .5mm shim on each side
Xray diff using Plato as filler
52mm ECS shafts
Rear:
2nd hole from top on shock tower
2.4/2.6 Xray progressive spring
300cst oil
4X1.1mm pistons
1.2 Xray bar(short endlinks and middle position on arm)
2.75 degrees camber L/R
2.75est degrees toe-in(using .5mm shim at the rear instead of stock .7mm)
1mm spacer in front of the rear arm(2mm behind)
Upper links middle hole on bulkhead
2mm under outer link
4.5mm under inner link
high roll center blocks(+.75)
2.5mm droop(measuring above ride height)
Stock track width
Stock wheel hex
Xray diff w/2000cst
50mm stock shafts
Notes:
All screws in upper deck
15 grams of weight under steering rack
Body: PF Mazdaspeed 6
Tires: Jaco blue's
Compound: Jack 2
Weight: 1397g
Front:
2nd hole from top on shock tower
2.7 Xray spring
300cst oil
4X1.1mm pistons
1.4 Xray bar(short endlinks)
2.25 degrees camber L/R
6 degree caster blocks
1 degree toe-out
1mm spacer in front/rear of arm
Upper links middle hole on bulkhead
2mm under outer link
2mm under inner link
middle roll center blocks
2mm droop(measuring above ride height)
1.5mm Akerman
1mm bumpsteer
stock servo tie-rod position(upper position on servo saver)
Stock track width(1.5mm spacers)
Stock wheel hex with .5mm shim on each side
Xray diff using Plato as filler
52mm ECS shafts
Rear:
2nd hole from top on shock tower
2.4/2.6 Xray progressive spring
300cst oil
4X1.1mm pistons
1.2 Xray bar(short endlinks and middle position on arm)
2.75 degrees camber L/R
2.75est degrees toe-in(using .5mm shim at the rear instead of stock .7mm)
1mm spacer in front of the rear arm(2mm behind)
Upper links middle hole on bulkhead
2mm under outer link
4.5mm under inner link
high roll center blocks(+.75)
2.5mm droop(measuring above ride height)
Stock track width
Stock wheel hex
Xray diff w/2000cst
50mm stock shafts
Notes:
All screws in upper deck
15 grams of weight under steering rack
Is there anything else you can list that was tried, but didn't work or just made it push or too on edge etc.
I ask as I'm trying to get to grips with possible changes etc before I get the car.
Skiddins
#562
Tech Apprentice
#563
Tech Apprentice
If I think of anything else, I will be sure to post it.
#564
Here's the Info Corey has given us put onto a T4 setup sheet.
There are a few bits missing.
http://www.piez0r.com/Skiddins/Xray%...ardman-IIC.pdf
There are a few bits missing.
http://www.piez0r.com/Skiddins/Xray%...ardman-IIC.pdf
#566
My LHS received the first kits today. Gonna pickup mine tomorrow with a friend that also ordered one ^^
#569
Tech Adept
Please check your manuals to see if they are missing som assembly steps here and there. Mine did quite a lot.
Had to go to Xray website for a complete assembly instruction.
Had to go to Xray website for a complete assembly instruction.
#570
Tech Initiate