R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

Reply
 
Thread Tools Search this Thread
Old 12-04-2012, 08:56 AM   #1786
Tech Master
 
Chaz955i's Avatar
 
Join Date: May 2009
Location: NE Ohio
Posts: 1,009
Trader Rating: 5 (100%+)
Default

Quote:
Originally Posted by John Piper View Post
Looking to get back into onroad.Its been 5+ years.lol
I'm looking to maybe get a T4.
It seems from what everyone has been posting,the car in kit form is real easy to drive?
What body is everyone using?what should I get?
Yes, kit setup is very easy to drive. Using Protoform LTC-R for a body.
__________________
At The Gate Bizzos
Chaz955i is offline   Reply With Quote
Old 12-04-2012, 09:18 AM   #1787
Tech Master
 
samnelso's Avatar
 
Join Date: Aug 2011
Location: Fitchburg, MA
Posts: 1,751
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by John Piper View Post
Looking to get back into onroad.Its been 5+ years.lol
I'm looking to maybe get a T4.
It seems from what everyone has been posting,the car in kit form is real easy to drive?
What body is everyone using?what should I get?
Personally, I drifted quite a ways away from the kit setup. Box stock was drivable, but not fast for my driving style at my track. If you're looking for a body, I'd say speed6 is the best body to start off with on carpet (assuming that's what you're running on at this time of the year).
__________________
Team Associated | Reedy | Airtronics

RC Excitement: Fitchburg, MA | RC Madness: Enfield, CT | Horsham RC
samnelso is offline   Reply With Quote
Old 12-04-2012, 10:12 AM   #1788
Tech Master
 
Xpress's Avatar
 
Join Date: Nov 2001
Location: Dirt sucks!
Posts: 1,585
Trader Rating: 3 (100%+)
Default

Quote:
Originally Posted by aussierevo View Post
i'm in the process of the build and having trouble setting the rear stabliser. When I'm lifting the rear arms on one side all works well ie. the other arm rises, but when I go to the opposite side, it fails to rise. I've check and recheck the downstops, check for binding and I'm basically at a loss as to why I can't get each side to rise as intented.

What am I missing, what can re-check to ensure I have right, as I'm at that stage where I'm at a lost.

appreciate any suggestions.
Take the bar off the back and put in on a flat surface to make sure the bar isn't twisted. Measure both links to make sure they are the same length. Back the setscrews off a bit so the bar drops freely. Tighten one screw at a time slowly until the bar starts to bind and then back off until the bar is free again.....do the same to the other side. Make sure the links pivot freely on the arms and that when tighten the collars on the end of the bar that they are spaced evenly on the end of the wire left and right.
__________________
"Desire is the key to motivation, but it's the determination and commitment to an unrelenting pursuit of laying it down - a commitment to excellence - that will enable you to attain the success you seek to beat ass."

-Espo
Xpress is offline   Reply With Quote
Old 12-04-2012, 10:27 AM   #1789
Tech Fanatic
 
erchn's Avatar
 
Join Date: Aug 2010
Location: Union City, CA
Posts: 779
Trader Rating: 7 (100%+)
Default

Quote:
Originally Posted by aussierevo View Post
i'm in the process of the build and having trouble setting the rear stabliser. When I'm lifting the rear arms on one side all works well ie. the other arm rises, but when I go to the opposite side, it fails to rise. I've check and recheck the downstops, check for binding and I'm basically at a loss as to why I can't get each side to rise as intented.

What am I missing, what can re-check to ensure I have right, as I'm at that stage where I'm at a lost.

appreciate any suggestions.
I had this problem as well. First, double check your stabilizer mounts which connect to the arm are the exact same length. Mine were, but it turned out my rear stabilizer bar was not flat, just a little bit but it made a huge difference. See picture.



I fixed it two ways.
1) hang the right side over the edge of the board holding the bar the way I'm showing, and push down then let it recover and see if it's still not flat. I had to push down until the bar was nearly at a 90 degree angle and it took a couple tries to get it flat, as this material is made to bend but recover back to where it was.
2) I then lengthened one of the stabilizer mounts a twist or two, until the arms lifted equally.

Hope that helps, or more specifically, I hope that's the problem you are having as well.
erchn is offline   Reply With Quote
Old 12-04-2012, 10:28 AM   #1790
Tech Fanatic
 
erchn's Avatar
 
Join Date: Aug 2010
Location: Union City, CA
Posts: 779
Trader Rating: 7 (100%+)
Default

Quote:
Originally Posted by Xpress View Post
Take the bar off the back and put in on a flat surface to make sure the bar isn't twisted. Measure both links to make sure they are the same length. Back the setscrews off a bit so the bar drops freely. Tighten one screw at a time slowly until the bar starts to bind and then back off until the bar is free again.....do the same to the other side. Make sure the links pivot freely on the arms and that when tighten the collars on the end of the bar that they are spaced evenly on the end of the wire left and right.
lol, beat me too it.
erchn is offline   Reply With Quote
Old 12-04-2012, 12:22 PM   #1791
Tech Fanatic
 
aussierevo's Avatar
 
Join Date: Apr 2007
Location: Brisbane Qld
Posts: 865
Trader Rating: 11 (100%+)
Default

guy's, thanks for the thoughts, I will give these suggestions a try.

thanks again.
__________________
Speed Passion F1.
Hobbywing ESC and Motor, SMC Batteries
Meakin Park Club Member
Team ARGO RC - Like us on Facebook
aussierevo is offline   Reply With Quote
Old 12-04-2012, 02:22 PM   #1792
Tech Regular
 
Adam B's Avatar
 
Join Date: Nov 2010
Location: Detroit, Mi
Posts: 411
Default

Quote:
Originally Posted by John Piper View Post
Looking to get back into onroad.Its been 5+ years.lol
I'm looking to maybe get a T4.
It seems from what everyone has been posting,the car in kit form is real easy to drive?
What body is everyone using?what should I get?
The body to run depends on the track layout and grip. Honestly, I agree the Speed 6 body is probably the best to start with as it has more of a neutral feel, where the P37 and LTCR will give you more front bite it seems.
Adam B is offline   Reply With Quote
Old 12-04-2012, 02:34 PM   #1793
Tech Master
 
samnelso's Avatar
 
Join Date: Aug 2011
Location: Fitchburg, MA
Posts: 1,751
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by aussierevo View Post
guy's, thanks for the thoughts, I will give these suggestions a try.

thanks again.
Adjust the symmetry of the swaybar action via the links that connect to the arm. You can lengthen or shorten the links until you get symmetry. Also, for fine-tuning, you can slide the swaybar through the aluminum ball that connects to the links. It's important that the swaybar dynamics side-to-side are the same, the links are what they are to achieve this symmetry.

To check swaybar symetry I put my car on blocks, then, with tires off, I carefully prop one of the stub axle shafts onto a 12th scale rear wheel (or whatever is handy to give a consistent placement) and measure the corresponding uptravel of the other side. I then do this to the other side, compare the measurements, and adjust as necessary.
__________________
Team Associated | Reedy | Airtronics

RC Excitement: Fitchburg, MA | RC Madness: Enfield, CT | Horsham RC
samnelso is offline   Reply With Quote
Old 12-04-2012, 06:25 PM   #1794
Tech Fanatic
 
aussierevo's Avatar
 
Join Date: Apr 2007
Location: Brisbane Qld
Posts: 865
Trader Rating: 11 (100%+)
Default

I've given it another try. The sway bar was bent just as much as in the pictures posted earlier. I've given it a 'tweak' and it seems to have done the trick. I might need to invest in a new one just to be sure.

thanks for all the help.
__________________
Speed Passion F1.
Hobbywing ESC and Motor, SMC Batteries
Meakin Park Club Member
Team ARGO RC - Like us on Facebook
aussierevo is offline   Reply With Quote
Old 12-04-2012, 06:56 PM   #1795
Tech Elite
 
haywood's Avatar
 
Join Date: Dec 2008
Location: Minnesota
Posts: 2,732
Trader Rating: 47 (100%+)
Default

Quote:
Originally Posted by samnelso View Post
Personally, I drifted quite a ways away from the kit setup. Box stock was drivable, but not fast for my driving style at my track. If you're looking for a body, I'd say speed6 is the best body to start off with on carpet (assuming that's what you're running on at this time of the year).
Sam,
Could you post some of your changes you made to the kit setup? Thanks
__________________
/ Roche Rapida 2015-2016 / Hobbywing / Team Scream / Rc Painting By Mikey / Ko Propo / MMR / Dri-Fit Mafia /
haywood is offline   Reply With Quote
Old 12-04-2012, 08:34 PM   #1796
Tech Master
 
Josh-n-ya's Avatar
 
Join Date: May 2011
Location: Alameda, CA
Posts: 1,991
Trader Rating: 70 (100%+)
Default

Quote:
Originally Posted by erchn View Post
lol, beat me too it.
So whatcha gonna do with your old Xray?
Josh-n-ya is offline   Reply With Quote
Old 12-04-2012, 09:31 PM   #1797
Tech Regular
 
Join Date: Oct 2012
Location: Moose Jaw, Saskatchewan
Posts: 297
Trader Rating: 1 (100%+)
Default

finally built but still waiting for my new esc



and my first paint job in 3 years and only my 3rd one every ....

rescue119 is offline   Reply With Quote
Old 12-04-2012, 10:21 PM   #1798
Tech Elite
 
nashrcracer's Avatar
R/C Tech Charter Subscriber
 
Join Date: Nov 2001
Location: LA - Lower Antioch
Posts: 4,849
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by erchn View Post
I had this problem as well. First, double check your stabilizer mounts which connect to the arm are the exact same length. Mine were, but it turned out my rear stabilizer bar was not flat, just a little bit but it made a huge difference. See picture.

I fixed it two ways.
1) hang the right side over the edge of the board holding the bar the way I'm showing, and push down then let it recover and see if it's still not flat. I had to push down until the bar was nearly at a 90 degree angle and it took a couple tries to get it flat, as this material is made to bend but recover back to where it was.
2) I then lengthened one of the stabilizer mounts a twist or two, until the arms lifted equally.

Hope that helps, or more specifically, I hope that's the problem you are having as well.

something Paul lemuiex told me when I was in cleveland at the holloween classic in 2011 was the collar on the sway bar can act as a cam for getting a slight out of flat sway bar back to flat. set screw up to set screw down makes a difference and is finer to get the correct side to side "feel" out of a sway bar then taking a round of the the ball ends.
__________________
RC50 As you come into this world, something else is also born. You begin your life, and it begins a journey towards you. It moves slowly, but it never stops. Wherever you go, whatever path you take, it will follow never faster, never slower, always coming. You will run, it will walk. You will rest, it will not. One day, you will linger in the same place too long you will sit too still, or sleep too deep. And when, too late, you rise to go, you will notice a second shadow next to yours. Your life will then be over.
nashrcracer is offline   Reply With Quote
Old 12-05-2012, 12:35 AM   #1799
Tech Master
 
samnelso's Avatar
 
Join Date: Aug 2011
Location: Fitchburg, MA
Posts: 1,751
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by haywood View Post
Sam,
Could you post some of your changes you made to the kit setup? Thanks
I uploaded a setup sheet if interested. Car is better than I am

http://forum.teamxray.com/xform/inde...ID=74&setup=t4
__________________
Team Associated | Reedy | Airtronics

RC Excitement: Fitchburg, MA | RC Madness: Enfield, CT | Horsham RC
samnelso is offline   Reply With Quote
Old 12-05-2012, 01:55 AM   #1800
Tech Adept
 
Join Date: Nov 2012
Posts: 104
Default

what make pinions is everyone running? 48dp or 64dp? and what are your reasons?

Thanks
Nathan Wilson is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Xray T3 2012 rasta_man Electric On-Road 4220 11-09-2016 02:45 PM
RC10B4/T4 Forum DerekL Electric Off-Road 14331 01-01-2016 03:18 PM
****HUGE AE T4 TRUCK TIRE SALE *** CRCDUDE R/C Items: For Sale/Trade 32 08-23-2010 09:55 AM


Tags
xray t4


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 02:58 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0