YOKOMO Touring Car BD-7
#5807
Tech Apprentice
Can anyone tell me the total length of the Yokomo SLF short shock? From end to end. Thanks in advanced.
#5809
Tech Apprentice
#5810
Tech Regular
iTrader: (23)
Hi guys... So I built my new bd7'15 2 weeks ago n ran 13.5 blinky with no issues.
However i put a 4.5t boosted on n down the main straight the rear driveshaft pin keeps getting thrown off the car, and then the dogbone goes flying and I end up with a 3-wheel drive car. I've tried thread locking the set screw, even tried thread locking the 2 ends of the driveshaft pin to the axle - no luck. Does anybody else have this problem n how can I fix it?
However i put a 4.5t boosted on n down the main straight the rear driveshaft pin keeps getting thrown off the car, and then the dogbone goes flying and I end up with a 3-wheel drive car. I've tried thread locking the set screw, even tried thread locking the 2 ends of the driveshaft pin to the axle - no luck. Does anybody else have this problem n how can I fix it?
#5811
Tech Master
iTrader: (11)
Hi guys... So I built my new bd7'15 2 weeks ago n ran 13.5 blinky with no issues.
However i put a 4.5t boosted on n down the main straight the rear driveshaft pin keeps getting thrown off the car, and then the dogbone goes flying and I end up with a 3-wheel drive car. I've tried thread locking the set screw, even tried thread locking the 2 ends of the driveshaft pin to the axle - no luck. Does anybody else have this problem n how can I fix it?
However i put a 4.5t boosted on n down the main straight the rear driveshaft pin keeps getting thrown off the car, and then the dogbone goes flying and I end up with a 3-wheel drive car. I've tried thread locking the set screw, even tried thread locking the 2 ends of the driveshaft pin to the axle - no luck. Does anybody else have this problem n how can I fix it?
#5812
Tech Regular
iTrader: (23)
You can try two things, lightly dremel the pin so the set screw can have more contact or try using heat shrink over the axle area. I've used Heat shrink in the front but never in the back so you're going have to experiment. I have experience a pin backing out before so I do dremel a small flat.
#5816
Tech Regular
iTrader: (2)
car wont turn....help??
I have a 14 black yokomo bd7...im running usgt wit hpi silver springs all around....the car has great rear traction but pushes like a dog going into a corner..i have 30wt associated in the shocks wit 3.0 toe in the rear...can some one give me a setup that will give me more steering...thanks
#5817
I have a 14 black yokomo bd7...im running usgt wit hpi silver springs all around....the car has great rear traction but pushes like a dog going into a corner..i have 30wt associated in the shocks wit 3.0 toe in the rear...can some one give me a setup that will give me more steering...thanks
If you need more use 1.5mm for the center link and/or lower front shock to #2 hole.
#5818
Tech Regular
iTrader: (2)
http://www.petitrc.com/reglages/yoko...USA2014052325/
If you need more use 1.5mm for the center link and/or lower front shock to #2 hole.
If you need more use 1.5mm for the center link and/or lower front shock to #2 hole.
#5819
Post your setup and track condition and I'm sure the guys in here can help you get close to what you want.
The setup I linkedis just a good all around setup that works well from low bite to medium from my experience.
The setup I linkedis just a good all around setup that works well from low bite to medium from my experience.
#5820
I have a 14 black yokomo bd7...im running usgt wit hpi silver springs all around....the car has great rear traction but pushes like a dog going into a corner..i have 30wt associated in the shocks wit 3.0 toe in the rear...can some one give me a setup that will give me more steering...thanks