3 Racing Sakura D3 CS Drift
#706
#707
Tech Initiate
Then my D3 is on it's way!
#708
#709
Tech Initiate
#711
you still want to do the KPI mod? I've just bought some yokomo type C upper arms to cut up for the top mount
I used some 12mm set screws for the lower arm to ball end connection
Last edited by pickled; 11-27-2012 at 01:36 AM.
#712
Did you get some Alloy pulleys? if you bought the alloy suspension mounts you'll need the pivot balls as well! get some alloy washers 1mm, 1.5mm use the 1.5mm washers on the suspension pins and the 1mm under the rear pulley mount helps with the slack belt issues. Be careful with the threads if you can get a 3mm tapping bit run that through the holes first with some light oil first (thanks eunique) then you won't strip the threads easily when you assemble it.
#713
sakura D3
+ YouTube Video | |
i just want to share my Sakura D3 drifting..... More Power to all Sakura D3 users
OD Rate reduced to 75%
all settings is default settings according to manual !
SP ReventonS and SP V3 13.5T motor for elec.
TowerPro mg995 for servo
Tx/Rx Futaba 4pk with 4pks Reciever
Hope you like it !
#714
i just want to share my Sakura D3 drifting..... More Power to all Sakura D3 users
OD Rate reduced to 75%
all settings is default settings according to manual !
SP ReventonS and SP V3 13.5T motor for elec.
TowerPro mg995 for servo
Tx/Rx Futaba 4pk with 4pks Reciever
Hope you like it !
OD Rate reduced to 75%
all settings is default settings according to manual !
SP ReventonS and SP V3 13.5T motor for elec.
TowerPro mg995 for servo
Tx/Rx Futaba 4pk with 4pks Reciever
Hope you like it !
#715
Tech Regular
iTrader: (3)
Nah you got to expect it at this time of the year, I made a big order last week and it didn't leave H/K till yesterday. So it probably won't get to me till next monday?
you still want to do the KPI mod? I've just bought some yokomo type C upper arms to cut up for the top mount
I used some 12mm set screws for the lower arm to ball end connection
you still want to do the KPI mod? I've just bought some yokomo type C upper arms to cut up for the top mount
I used some 12mm set screws for the lower arm to ball end connection
would like to see your schematics on how your mod is going to be put together so I can follow along.
#716
Tech Regular
iTrader: (3)
i just want to share my Sakura D3 drifting..... More Power to all Sakura D3 users
OD Rate reduced to 75%
all settings is default settings according to manual !
SP ReventonS and SP V3 13.5T motor for elec.
TowerPro mg995 for servo
Tx/Rx Futaba 4pk with 4pks Reciever
Hope you like it !
OD Rate reduced to 75%
all settings is default settings according to manual !
SP ReventonS and SP V3 13.5T motor for elec.
TowerPro mg995 for servo
Tx/Rx Futaba 4pk with 4pks Reciever
Hope you like it !
would you mind sharing your pulley set up and maybe pics?
#717
C-13/13
R-18/22
i just replace the stock 22t rear pulley with 18t pulley
will post a pic. of kit later thanks
yes i keep the stock rims but i replace the spark tire because i dont like the traction of that tire ,
it takes a lot of effort and time removing tire from rims i think 3R use special adhesive on tire and rims thanks
#719
Pickled... wow! nice work man! clean cut well thought out. I like.
My initial thoughts from reviewing the manual.. great touring style suspension geometry DNA. Good prospects. Liked the long 31mm springs, hopefully easy to pass strict tech inspection on carpet. Once I got the chassis, would think about modding the upper inboard camber link positions to be horizontal, rather than vertical on the towers. Thought about adding anti roll bars. Now the long wait....
My initial thoughts from reviewing the manual.. great touring style suspension geometry DNA. Good prospects. Liked the long 31mm springs, hopefully easy to pass strict tech inspection on carpet. Once I got the chassis, would think about modding the upper inboard camber link positions to be horizontal, rather than vertical on the towers. Thought about adding anti roll bars. Now the long wait....
#720
F-38/13
C-13/13
R-18/22
i just replace the stock 22t rear pulley with 18t pulley
will post a pic. of kit later thanks
yes i keep the stock rims but i replace the spark tire because i dont like the traction of that tire ,
it takes a lot of effort and time removing tire from rims i think 3R use special adhesive on tire and rims thanks
C-13/13
R-18/22
i just replace the stock 22t rear pulley with 18t pulley
will post a pic. of kit later thanks
yes i keep the stock rims but i replace the spark tire because i dont like the traction of that tire ,
it takes a lot of effort and time removing tire from rims i think 3R use special adhesive on tire and rims thanks
Pickled... wow! nice work man! clean cut well thought out. I like.
My initial thoughts from reviewing the manual.. great touring style suspension geometry DNA. Good prospects. Liked the long 31mm springs, hopefully easy to pass strict tech inspection on carpet. Once I got the chassis, would think about modding the upper inboard camber link positions to be horizontal, rather than vertical on the towers. Thought about adding anti roll bars. Now the long wait....
My initial thoughts from reviewing the manual.. great touring style suspension geometry DNA. Good prospects. Liked the long 31mm springs, hopefully easy to pass strict tech inspection on carpet. Once I got the chassis, would think about modding the upper inboard camber link positions to be horizontal, rather than vertical on the towers. Thought about adding anti roll bars. Now the long wait....