Yokomo MR4TC-BD
#1081
Tech Elite
iTrader: (9)
Originally posted by chaini
Where did you get that from????
The Acerpage is cool tough
Where did you get that from????
The Acerpage is cool tough
One other reason why I think Acers won't work well is normaly you can remove one sheild as to free up the drive train but with the BD the drive train is wide open so you risk damage to the bearings by opening up the sheilds.
Hope I helped.
Randy any suggestions that you found were usefull last night and how did you place in the races?
On the steering rack and the turnbuckles switch to the bottom it looks as if the switch the spacer to the steering arm you would keep the angle so would that still change bump steer?
I was just wondering if it looks to be a good change or should I leave well enough alone.
Thanks for the help guys,
Stephen <><
Also here is the spring rate chart for every kind of spring....very usefull to have printed on the back of your gear ratio chart. Here is both links.
http://www.rcingreece.com/index.asp?...ing_comparison
http://www.gearchart.com/index.cfm?f...n=chart.create
#1083
#1084
Originally posted by Matt Howard
Hey guys, here's a setup from Chris Grainger, a Yokomo factory driver in England.
Front
Drive train - one-way [and center]
Roll-bar - gold
Caster block - 4 plastic high hole
Camber - -1.5
Toe angle - 0
Kick up - 0
Susp spacer - 2 blue washers under each
Steering arm - -1 trailing spacer under
Bladder - std with no foam, use 1 o ring
Body - sss
Shock end - short
Length - 61.5
Spring - white
Oil - 400
Piston - #3 std
Droop - 5 to bottom of caster block
Top link inner - 1mm under ball
Top link outer - king pin
Shock upper - all-in
Shock lower - middle
Susp arm - plastic
W/B - 4-0
Ride height - 5mm
Ackermann - one more forward than std
Rear
Roll-bar - silver
Camber - -1.5
Toe angle inner - 2 new lower
Toe angle outer - 0.5 new alloy
Susp spacer - 0
Bladder - std with no foam, use 1 o ring
Body - sss
Shock end - short
Length - 61.5
Spring - blue
Oil - 350
Piston - #3 std
Droop - 4
Top link inner - 0 washers
Top link outer - inside hole, long std ball
Shock upper - 3rd out
Shock lower - outer
Susp arm - plastic
W/B - 2-2
Ride height - 5.5
Body - Dodge 2.0
Additive - Tweak
Motor - check point 8x2
Ratio - 7.50 :1
Wheel - proline 26mm
Insert - Hara gray
Tyre - cs-22
Battery - novak 3300
Hey guys, here's a setup from Chris Grainger, a Yokomo factory driver in England.
Front
Drive train - one-way [and center]
Roll-bar - gold
Caster block - 4 plastic high hole
Camber - -1.5
Toe angle - 0
Kick up - 0
Susp spacer - 2 blue washers under each
Steering arm - -1 trailing spacer under
Bladder - std with no foam, use 1 o ring
Body - sss
Shock end - short
Length - 61.5
Spring - white
Oil - 400
Piston - #3 std
Droop - 5 to bottom of caster block
Top link inner - 1mm under ball
Top link outer - king pin
Shock upper - all-in
Shock lower - middle
Susp arm - plastic
W/B - 4-0
Ride height - 5mm
Ackermann - one more forward than std
Rear
Roll-bar - silver
Camber - -1.5
Toe angle inner - 2 new lower
Toe angle outer - 0.5 new alloy
Susp spacer - 0
Bladder - std with no foam, use 1 o ring
Body - sss
Shock end - short
Length - 61.5
Spring - blue
Oil - 350
Piston - #3 std
Droop - 4
Top link inner - 0 washers
Top link outer - inside hole, long std ball
Shock upper - 3rd out
Shock lower - outer
Susp arm - plastic
W/B - 2-2
Ride height - 5.5
Body - Dodge 2.0
Additive - Tweak
Motor - check point 8x2
Ratio - 7.50 :1
Wheel - proline 26mm
Insert - Hara gray
Tyre - cs-22
Battery - novak 3300
#1088
Tech Master
iTrader: (35)
BD Shock Question
I don't know if you guys saw my question, but...
Will the BD shocks work with my full compliment of Yokomo springs, or will I need to purchase a Rayspeed set?
Which Rayspeed springs (colors) are included in the kit?
Are the BD shocks the same as the CGM/SD shocks that I already have?
tanks.
Will the BD shocks work with my full compliment of Yokomo springs, or will I need to purchase a Rayspeed set?
Which Rayspeed springs (colors) are included in the kit?
Are the BD shocks the same as the CGM/SD shocks that I already have?
tanks.
#1089
Tech Champion
iTrader: (9)
Re: BD Shock Question
Originally posted by Geppetto
I don't know if you guys saw my question, but...
Will the BD shocks work with my full compliment of Yokomo springs, or will I need to purchase a Rayspeed set?
Which Rayspeed springs (colors) are included in the kit?
Are the BD shocks the same as the CGM/SD shocks that I already have?
tanks.
I don't know if you guys saw my question, but...
Will the BD shocks work with my full compliment of Yokomo springs, or will I need to purchase a Rayspeed set?
Which Rayspeed springs (colors) are included in the kit?
Are the BD shocks the same as the CGM/SD shocks that I already have?
tanks.
BD shocks are the SSS type. I forget what was on the SD...I sold it a long while ago...
don't know about the compatibility with the other Yokomo springs...
#1091
R/C Tech Elite Member
iTrader: (47)
Originally posted by Mr. Shookie
Randy any suggestions that you found were usefull last night and how did you place in the races?[/url]
Randy any suggestions that you found were usefull last night and how did you place in the races?[/url]
I'll post a pic of the one I ran yesterday, but tonight I am going to cut off the stock aluminum ballstud mounts and make a carbon piece that I can make 3 mounting locations on, rather than 2.
I didnt stay to race, just worked on my car and tested all day.