Yokomo MR4TC-BD
#4996
Tech Addict
iTrader: (2)
Originally Posted by EVS
Can anyone point me in the right direction? I am looking for a 3mm chassis and top deck for my BD. Thanks
You have three choices:
1) wait for someone to sell theirs
2) Find someone to machine you one
3) Use a team bomber upper deck and yokomo stiff chassis
Last edited by smojoe; 04-29-2006 at 08:58 AM.
#4997
Tech Initiate
I was given 2 servo horns for HiTec servos as thats what I use and a servo horn for a KO. Both of the Hitec ones are now stripped and I am now using the one for the KO.
Paul
Paul
#4998
Tech Initiate
does anyone know if yokomo are planning to relese a new tc based on the new buggy with the motor in the middle ???
#4999
Tech Elite
iTrader: (10)
Originally Posted by pheyhoe
Why????? lol
It will just smash surely..? no?
Also, pwracing, are you deffinately using the correct type of horn for your servo? the three that come with the kit of for three makes of servo. I am running a 2343 and have never had one slip. Ive had a few break though. Only in big hits.
It will just smash surely..? no?
Also, pwracing, are you deffinately using the correct type of horn for your servo? the three that come with the kit of for three makes of servo. I am running a 2343 and have never had one slip. Ive had a few break though. Only in big hits.
Just to try it out the guy also custom made me a carbon Fiber Center Shaft and Hinge Pins sets. Hey for $10 can't beat that.
#5000
Tech Addict
iTrader: (15)
Originally Posted by yzafrir
does anyone know if yokomo are planning to relese a new tc based on the new buggy with the motor in the middle ???
#5001
Tech Elite
POPs, sent you a pm
#5002
Hi GUys
A quick question
Way back in this thread there is a set of instructions for locking the centre oneway pulley. can anyone post a link or tell me how it is done, or is there a
fixed pulley option part available and what is the part # ?
My one way has let go and wont hook up and I have a new shaft on it already
and dont know what to do about it.
thanks in adavance
geoff
A quick question
Way back in this thread there is a set of instructions for locking the centre oneway pulley. can anyone post a link or tell me how it is done, or is there a
fixed pulley option part available and what is the part # ?
My one way has let go and wont hook up and I have a new shaft on it already
and dont know what to do about it.
thanks in adavance
geoff
#5004
Thanks Jochim
#5005
Tech Adept
Quick bit of news.
Chris Grainger starts his BRCA Modified title defence in the best way with a TQ and win at the 1st round at Stafford.
Well done Chris.
Chris Grainger starts his BRCA Modified title defence in the best way with a TQ and win at the 1st round at Stafford.
Well done Chris.
#5007
Tech Champion
iTrader: (32)
Originally Posted by pops
Thought I would let you guys know about a parts sale at Yokomo USA. Buy $100 get 10% off, $200 get 20% off and $300 get 30% off. That's a pretty good deal.
#5008
Tech Master
iTrader: (1)
Originally Posted by STLNLST
Good run yesterday. Mo and I will more than likely be going to Ripon next weekend for a little more testing. I'm going for sure and Mo is on the fence as of right now.
#5009
Tech Fanatic
iTrader: (1)
Pops..Just a little note to tell you what I found...The BD steers and powers thru and out of corners with a double one way.Ive tried spool and diff but found they were not as good.Playing with rollcenters gives good feedback andif you remove the rear swaybar you will be suprised...it gives you more turn in and makes the car quite snappy...changes direction very good.Remember I run stock 27turn but at the front end.Hope this helps,I have just sold my BD...Having a go with a Hara Cyclone....
Bob
Bob
#5010
Originally Posted by pops
Thought I would let you guys know about a parts sale at Yokomo USA. Buy $100 get 10% off, $200 get 20% off and $300 get 30% off. That's a pretty good deal.