Hot Bodies Cyclone
Tech Master
iTrader: (6)
Is Andy Moore Edition Cyclone Li-Po and Brushless friendly? I’ve heard something about new motor mount pacifically designed to make brushless motor fits. Does it come with the kit or I have to buy it separate?
Tech Master
The BL motor mounts are raised up, so if you run MOD with BIG spurs then you would want that, I remember Marcos j said 108 fits no mods, and any bigger sticks out the bottom of the chassis....
But if yours doing stock or 19T, it doesnt matter
It doesnt come with the kit
Tech Elite
iTrader: (11)
That should read 6 cell brushless mod, if you are running 5 cell mod you probably wont need the brushless motor mount.
Actually you might if you go below 3.5 with an LRP
Actually you might if you go below 3.5 with an LRP
Tech Elite
iTrader: (138)
hey mangoman, is the hobby popular in australia? Are parts/kits expensive? How much in USD are NIB andy moore cyclones there? How about parts?
Tech Master
iTrader: (4)
It is not as big in Australia as it is in the US. A morespeed in australia will set you back about US $600 and parts are a little more as well. Most people still buy from Hong Kong and the US as it still works out cheaper.
Tech Elite
iTrader: (101)
Does anyone have a Moore Speed WCE Cyclone they want to sell? Either from the states or Australia, looking at spending around $200 as it is an old car now. Postage to Brisbane, Australia 4000.
Cheers
Adrian
Cheers
Adrian
Tech Elite
iTrader: (138)
Tech Addict
iTrader: (1)
And they say this car is old this is for all my Cyclone lovers out there
Florida State Series
I have tabulated the Manufacturers points... and WOW is it closer then ever
This is after 3 rounds... I am missing who finsihed 3rd in mod at both the last two races.... When that is posted, I will update it further
Corally 46
Hot Bodies 44
Schumacher 42
Serpent 40
Associated 32
Losi 18
Xray 9
Florida State Series
I have tabulated the Manufacturers points... and WOW is it closer then ever
This is after 3 rounds... I am missing who finsihed 3rd in mod at both the last two races.... When that is posted, I will update it further
Corally 46
Hot Bodies 44
Schumacher 42
Serpent 40
Associated 32
Losi 18
Xray 9
Tech Elite
iTrader: (63)
Tech Elite
iTrader: (138)
why does the kit stock setup call for a thicker rear sway bar than the front? It just doesn't make sense
Tech Elite
iTrader: (11)
.
Tech Elite
iTrader: (11)
Also we dont have many kids racing (or at least in sydney) which i guess could be due to the large initial cost of getting into competitive racing.
Tech Elite
iTrader: (50)
Wimpy diff screws & wandering layshaft
Thought I had the diffs figured out with the alum. outdrives and then broke another diff screw tonight. Thats three in three weeks.
I just dropped the one way in front and said forget about it for now. I was running the front diff tight admitadly. I'm gonna sand the next diff rings and drill the outdrives to accept a beefy screw. Any suggestions ??
I built the car as per the instructions and the layshaft wanders and the bearings are not seated tightly in the bulkheads any suggestions? Locktite on the outside?
I just dropped the one way in front and said forget about it for now. I was running the front diff tight admitadly. I'm gonna sand the next diff rings and drill the outdrives to accept a beefy screw. Any suggestions ??
I built the car as per the instructions and the layshaft wanders and the bearings are not seated tightly in the bulkheads any suggestions? Locktite on the outside?
Tech Elite
iTrader: (28)
Here we are! heres my Cyclone with its latest body...
Those rims are just for show btw.
Those rims are just for show btw.