4LikesReflex Suspension Dynamics (RSD) TC6 Upgrades (vertical ball studs, pistons,etc)
01-27-2012, 10:15 AM
#710
f1o7x9- regarding the pistons, how are they not smooth? did you check them to see if they had any rough edges? They should be just as smooth, if not smoother than the stock units. If you feel like you received some defective ones, I will replace them free of charge. 
You should not have to sand anything though. Double and triple check that it is the pistons and not something else that is causing this. Not saying it could not be the pistons though. Sometimes, stuff can be out of spec.
mtbboy- I have a couple of set-ups on the thread here somewhere. What surface are you running on? I need to know so I can point you in the right direction.
You should not have to sand anything though. Double and triple check that it is the pistons and not something else that is causing this. Not saying it could not be the pistons though. Sometimes, stuff can be out of spec.mtbboy- I have a couple of set-ups on the thread here somewhere. What surface are you running on? I need to know so I can point you in the right direction.
01-27-2012, 11:00 AM
#711
Run them in on the track. I noticed yesterday after building my new car that the shocks felt a little "scratchy" with all new parts yesterday. On my old car, this was not the case.
However, after a couple of runs, I noticed everything got smooth on the car. Now they are as smooth as my old shocks. My thinking is that they just need to break in.
However, after a couple of runs, I noticed everything got smooth on the car. Now they are as smooth as my old shocks. My thinking is that they just need to break in.
01-27-2012, 11:12 AM
#712
So i went home and I checked the piston, the pistons look really smooth, I didn't sand them and I tried all of them on some new set of shocks and on my old shocks and they where the same results. I put back the old ones and it was nice and smooth, the only thing that I could see that was wrong was that your pistons where not the same size they are a little smaller so when they where inside the shock body there was a little slop
I hope you get the issue figured out and are able to the RSD stuff! It is a great upgrade!
01-27-2012, 01:46 PM
#713
Ok I will try then today and at tomorrow races
01-30-2012, 12:33 PM
#714
Good luck to Reflex Drivers Jeff Cuffs and Matt Ward at the Snowbirds! Matt and Jeff are both running 17.5 Blinky TC, and I believe Jeff is running 17.5 boosted TC as well (Matts also running 17.5 pan). I wish I was tearing it up there with them
01-31-2012, 05:45 PM
#716
Bladders will be about a month or so... With the lunar year holiday everything is shut down for another week or two overseas at the factory where we get our bladders made.
And yes, good luck to all the RSD drivers at the 'birds... Jeff, Matt and whoever else I am missing.
Keven H, will also be representing for RSD, which is so exciting!!! Keven will be testing a few of our items...
And yes, good luck to all the RSD drivers at the 'birds... Jeff, Matt and whoever else I am missing.
Keven H, will also be representing for RSD, which is so exciting!!! Keven will be testing a few of our items...
02-08-2012, 10:55 PM
#719
Hello,
just curious how are the DCJs progressing.
PS: the shipping rates were raised drastically for Europe!? 200% or more ...
just curious how are the DCJs progressing.
PS: the shipping rates were raised drastically for Europe!? 200% or more ...
02-09-2012, 06:46 AM
#720
Tech Adept
I have reflex bladders pm me with your story I can send them out I ordered 6 sets used one lolo
