Reflex Suspension Dynamics (RSD) TC6 Upgrades (vertical ball studs, pistons,etc)
#2656
It might be the wave of the future, but who knows, what is old is new is old... We use to have this on the old Schumachers and we hated it because when you tapped, the toe would be off. I do see where there can be a benefit though, but I think with the 6.2, it's in the arm length when you fit front arms in the rear that I believe is making the biggest difference.
#2659
We worked on a good base set-up for the aluminum chassis for carpet this past Saturday. The car felt really, really good.
Here it goes:
Front:
3x1.1 Piston 40wt
Black Yokomo Spring/ RSD white
Short Camber links
B Hole Lower Arm
OOXO OXOO Upper Tower
2mm under inside link
1mm under outside link (silver stud)
1mm Ackerman Shim
Front Wheelbase all the way short
1mm Roll Center Shims under all front suspension Mounts
( . ) ( . ) FF
( ..) (.. ) FR
2 Deg Camber
Yellow Swaybar
2-2.5mm droop over ride height
Rear:
3x1.1 Piston 40wt
Black Yokomo Spring/ RSD white
Short Camber links
B Hole Lower Arm
OOXO OXOO Upper Tower
1mm under inside link
2mm under outside link (silver stud)
Rear Wheelbase 1mm in front of rear arms
1mm Roll Center Shims under all front suspension Mounts
( ..) (.. ) RF
( ..) (.. ) RR
2 Deg Camber
Yellow Swaybar
2-2.5mm droop over ride height
Rear Diff 3000cst oil
Spool Front
Diffs Mid low F/R
Battery Plugs back
Body: MS6/ Montech Nazda 2
Here it goes:
Front:
3x1.1 Piston 40wt
Black Yokomo Spring/ RSD white
Short Camber links
B Hole Lower Arm
OOXO OXOO Upper Tower
2mm under inside link
1mm under outside link (silver stud)
1mm Ackerman Shim
Front Wheelbase all the way short
1mm Roll Center Shims under all front suspension Mounts
( . ) ( . ) FF
( ..) (.. ) FR
2 Deg Camber
Yellow Swaybar
2-2.5mm droop over ride height
Rear:
3x1.1 Piston 40wt
Black Yokomo Spring/ RSD white
Short Camber links
B Hole Lower Arm
OOXO OXOO Upper Tower
1mm under inside link
2mm under outside link (silver stud)
Rear Wheelbase 1mm in front of rear arms
1mm Roll Center Shims under all front suspension Mounts
( ..) (.. ) RF
( ..) (.. ) RR
2 Deg Camber
Yellow Swaybar
2-2.5mm droop over ride height
Rear Diff 3000cst oil
Spool Front
Diffs Mid low F/R
Battery Plugs back
Body: MS6/ Montech Nazda 2
#2660
Tech Addict
iTrader: (22)
Can someone help me with the parts selection to make for parts to rebuild my V2 Narrow DCJ's for my TC6.1? I lost a small pin and retaining ring last race and need to order some replacements. I see the rings but no pins to order. Part # RSD070-1 says pins in the description but does not show them in the pic. Help please.
#2661
Tech Fanatic
iTrader: (7)
Can someone help me with the parts selection to make for parts to rebuild my V2 Narrow DCJ's for my TC6.1? I lost a small pin and retaining ring last race and need to order some replacements. I see the rings but no pins to order. Part # RSD070-1 says pins in the description but does not show them in the pic. Help please.
http://www.reflexracing.net/RSD-DCJ-...cs_p_1124.html
E
#2662
Tech Addict
iTrader: (22)
I think those are for just the hex hubs as the pins for the DCJ's are two sizes. One longer, one shorter. The parts I am looking for are in this picture https://reflexracing.3dcartstores.co...J_Exploded.jpg. They are left side ring and pin part. I'll be darned if I can find them on the part list on their site.
#2663
Tech Fanatic
iTrader: (7)
I think those are for just the hex hubs as the pins for the DCJ's are two sizes. One longer, one shorter. The parts I am looking for are in this picture https://reflexracing.3dcartstores.co...J_Exploded.jpg. They are left side ring and pin part.
#2664
Did I hear a rumor that you are going to product a run of aluminum chassis for the RX4 v1?
#2666
Tech Elite
iTrader: (49)
Can someone help me with the parts selection to make for parts to rebuild my V2 Narrow DCJ's for my TC6.1? I lost a small pin and retaining ring last race and need to order some replacements. I see the rings but no pins to order. Part # RSD070-1 says pins in the description but does not show them in the pic. Help please.
#2667
Christian, I might be interested in having one of these aluminum plates as well for the '13. Let me know the cost as well.