Thunder Power RC Z3R Motors
#496
Tech Rookie
Why does thunder power not list kv ratings or suggested voltages? Looking for a spec on the Z3R 550 4 turn. Has anyone done some independent research?
#497
Thunder Power Z3R 550 Motors
4.0 4.5 5.0 5.5
Part Number TPM-550A040 TPM-550A045 TPM-550A050 TPM55A055
Voltage 7.4 7.4 7.4-11.1 7.4-11.1
RPM/7.4V 37814 33596 30340 27602
kV 5110 4540 4100 3730
Power (W) 950 900 850 800
Max Current (A) 133 126 120 110
Efficiency (%) 92 92 94 94
Diameter (mm) 35.8 35.8 35.8 35.8
Length (mm) 65.3 65.3 65.3 65.3
Shaft Diameter (mm) 5.0 5.0 5.0 5.0
Weight (g) 248 248 248 248
#500
All the stators are interchangeable.
#501
Tech Master
iTrader: (49)
I think you might want to check that out. Stock stators are interchangeable with other stock stators. Mod stators are interchangeable with other mod stators. But you can't mix the 2.
This from page 17 post #249
Let me try to explain, winds 7.5t to 21.5t have a shorter stator than the modified 3.5 to 6.6t motors. There are two different cans for the motors. One for stock and one for mod. So the short answer is a mod stator will not fit in a stock can. We only offer the stock can as a replacement at this time. There willbe new mod cans coming soon
This from page 17 post #249
Let me try to explain, winds 7.5t to 21.5t have a shorter stator than the modified 3.5 to 6.6t motors. There are two different cans for the motors. One for stock and one for mod. So the short answer is a mod stator will not fit in a stock can. We only offer the stock can as a replacement at this time. There willbe new mod cans coming soon
#502
Tech Regular
Wat rotor comes with the 17.5 motor? Is it the red or the green one?
Thanks
Thanks
#504
Tech Regular
#505
I think you might want to check that out. Stock stators are interchangeable with other stock stators. Mod stators are interchangeable with other mod stators. But you can't mix the 2.
This from page 17 post #249
Let me try to explain, winds 7.5t to 21.5t have a shorter stator than the modified 3.5 to 6.6t motors. There are two different cans for the motors. One for stock and one for mod. So the short answer is a mod stator will not fit in a stock can. We only offer the stock can as a replacement at this time. There willbe new mod cans coming soon
This from page 17 post #249
Let me try to explain, winds 7.5t to 21.5t have a shorter stator than the modified 3.5 to 6.6t motors. There are two different cans for the motors. One for stock and one for mod. So the short answer is a mod stator will not fit in a stock can. We only offer the stock can as a replacement at this time. There willbe new mod cans coming soon
#506
Tech Elite
iTrader: (15)
Ok, that makes sense. So really the compatibility is not with 'mod' and 'stock', but with specific winds. The info I got from ThunderPower by email was that my 10.5 (stock) stator would work in an 8.5 (mod) can, so I assumed that mod and stock stators were interchangeable.
#508
#509
Tech Adept
Does anyone have a guide or video of how to disassemble / assemble the motors.
Should you aim to remove all play from the shaft?
Thanks
Should you aim to remove all play from the shaft?
Thanks
#510
Tech Master
iTrader: (49)
Just remove the 3 screws and pull the red and silver can halves apart. The stator will be left with the rotor inside. Pull the rotor out. I would just shim it so thst it floats freely. You don't want it to bind. Just enough side to side play. Usually a couple mm of play is good.