2LikesXray T3 2011
08-02-2011, 06:08 AM
#2686
http://www.rc-mushroom.com/product_i...ducts_id=22994
Spotted this on rcmushroom. Might be a good thing to try for those using the 90 degree servo turn mod. Might add to it to my next purchase order form there to give it a go.
Spotted this on rcmushroom. Might be a good thing to try for those using the 90 degree servo turn mod. Might add to it to my next purchase order form there to give it a go.
08-02-2011, 02:38 PM
#2687
ill be grabing one off them soon looks prety good
08-02-2011, 03:47 PM
#2688
Anyone know who has the XRAY gear diff in stock at the moment, rcmushroom is out, amain dont stock, cant seem to find it anywhere
08-02-2011, 05:14 PM
#2689
Which roll center mount in which position gives the LEAST roll L,H or old silver round?
08-02-2011, 05:44 PM
#2690
Tech Master
08-03-2011, 06:30 AM
#2692
Hi All
Ive build myself a t3 with exotek chassis ,t3 bulkheads etc. and 008 parts but as you know t3 rear shock tower 4 quick roll centre points are more upward compare to 008-9
What do you think should I buy, t3 rear shock tower or H1-h2 can sort that out?
Or leave it as it is???
Cheers
Ive build myself a t3 with exotek chassis ,t3 bulkheads etc. and 008 parts but as you know t3 rear shock tower 4 quick roll centre points are more upward compare to 008-9
What do you think should I buy, t3 rear shock tower or H1-h2 can sort that out?
Or leave it as it is???
Cheers
Last edited by yokemad; 08-03-2011 at 06:52 AM.
08-03-2011, 08:23 AM
#2693
CSO New T3'11 2.2mm Carbon Chassis ( Servo Support 90 deg turn )
08-03-2011, 09:26 AM
#2696
still need less roll for VTA 25.5 the WIDE tires and tall sidewall have plenty the car doesn't need to roll and make more grip
08-03-2011, 09:52 AM
#2697
Tech Adept
$72.95
$45.00
08-03-2011, 10:08 AM
#2698
Don't forget there are many different grade of quality CF available 
It's a bit early too early to make judgement ...
It's a bit early too early to make judgement ...
08-03-2011, 10:09 AM
#2699
Hi All
Ive build myself a t3 with exotek chassis ,t3 bulkheads etc. and 008 parts but as you know t3 rear shock tower 4 quick roll centre points are more upward compare to 008-9
What do you think should I buy, t3 rear shock tower or H1-h2 can sort that out?
Or leave it as it is???
Cheers
Ive build myself a t3 with exotek chassis ,t3 bulkheads etc. and 008 parts but as you know t3 rear shock tower 4 quick roll centre points are more upward compare to 008-9
What do you think should I buy, t3 rear shock tower or H1-h2 can sort that out?
Or leave it as it is???
Cheers
08-03-2011, 10:17 AM
#2700
I'd use the 008 shock tower and go after the inner rc adjusters. Go back a couple of posts where Craig M (i think) does a quick synopsis of link angle and how it works, this should benefit you with the 008 tower and just adjust on the outer to fine tune the angle. You could also post the same question to Paul L, I know they used to run the 008 but not sure if they still do on the 11.