USGT
|
|||
#361
What are the heat and main times for that class?
#362
Tech Champion
iTrader: (2)
USGT Class Rules and Specifications
Chassis Specification:
Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
Weight Specification:
4wd 1450g weight Fwd 1400g weight
Body Specifications:
Any 190mm or 200mm body. Body can be any body that is NOT on the ROAR T2 body list. NO Trucks
Any "SCALE" molded wings can be used. Lexan wings 10mm maximum height / side dam height
Scale type race liveries encouraged
Tire & Wheel Specifications:
Tires-Any treaded (non slick) non belted rubber tire available 24 or 26mm. Removing belts from belted tires is not allowed. Must used a non-molded (ex. open cell foam) insert or no insert. Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Wheels- Any 24 or 26mm spoke (non-dish) type wheel
While the above is the ideal for this class, a track or series may approve a premounted tire, slick tires being acceptable. A spoked wheel is encouraged if possible for premounted tires
Ride Height Specification:
Minimum ride height is 5mm.
Motor Specifications:
21.5 + 2s lipo batteries No tuning rotors, must use OEM rotor 12.3-12.5mm
Approved ESCs:
ESC ROAR approved spec software or USVTA list
Race Specification:
6 minute qualifiers
8 minute mains
Battery Specifications:
ROAR approved hard case batteries
Chassis Specification:
Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
Weight Specification:
4wd 1450g weight Fwd 1400g weight
Body Specifications:
Any 190mm or 200mm body. Body can be any body that is NOT on the ROAR T2 body list. NO Trucks
Any "SCALE" molded wings can be used. Lexan wings 10mm maximum height / side dam height
Scale type race liveries encouraged
Tire & Wheel Specifications:
Tires-Any treaded (non slick) non belted rubber tire available 24 or 26mm. Removing belts from belted tires is not allowed. Must used a non-molded (ex. open cell foam) insert or no insert. Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Wheels- Any 24 or 26mm spoke (non-dish) type wheel
While the above is the ideal for this class, a track or series may approve a premounted tire, slick tires being acceptable. A spoked wheel is encouraged if possible for premounted tires
Ride Height Specification:
Minimum ride height is 5mm.
Motor Specifications:
21.5 + 2s lipo batteries No tuning rotors, must use OEM rotor 12.3-12.5mm
Approved ESCs:
ESC ROAR approved spec software or USVTA list
Race Specification:
6 minute qualifiers
8 minute mains
Battery Specifications:
ROAR approved hard case batteries
#366
Tech Master
iTrader: (3)
True. Club racing I can't see that it matters. In fact, at 21.5 speeds, it probably doesn't at all, anyway. Either way, the 'spirit' of the class is 'real race cars'. I was just looking to do something different. I'm sure if someone wanted to get snarky about it, they would try to read something about no vans in the 'no trucks' rule.
#367
Tech Master
iTrader: (2)
True. Club racing I can't see that it matters. In fact, at 21.5 speeds, it probably doesn't at all, anyway. Either way, the 'spirit' of the class is 'real race cars'. I was just looking to do something different. I'm sure if someone wanted to get snarky about it, they would try to read something about no vans in the 'no trucks' rule.
#368
Tech Champion
iTrader: (2)
On one hand I would say that aerodynamics make a difference always, even at slow speeds and even if that differrence is not noticeable. It is there.
That however would not stop me from running a sports car body among the Saleens and McClarens or for that matter run a VTA shell on my USGT chassis. I don't think its enough of a difference for me to not run whatever I want for the sake of handling.
That however would not stop me from running a sports car body among the Saleens and McClarens or for that matter run a VTA shell on my USGT chassis. I don't think its enough of a difference for me to not run whatever I want for the sake of handling.
#374
Tech Champion
iTrader: (32)
Join Date: Aug 2001
Location: In a land of mini-mighty mental giants
Posts: 8,854
Trader Rating: 32 (100%+)
I guess I havent been pimpin this enough....so here goes...Nice Pics guys!
#375
Is this the Tamiya cockpit that fits:
http://www3.towerhobbies.com/cgi-bin...?&I=LXYJA5&P=7
What about Pro-Line Pro Driver:
http://www3.towerhobbies.com/cgi-bin...?&I=LXAVEK&P=7
Now these cockpits fit all RCGT/USGT bodies or will that just depend?
http://www3.towerhobbies.com/cgi-bin...?&I=LXYJA5&P=7
What about Pro-Line Pro Driver:
http://www3.towerhobbies.com/cgi-bin...?&I=LXAVEK&P=7
Now these cockpits fit all RCGT/USGT bodies or will that just depend?