R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 12-23-2004, 10:29 PM   #9931
Tech Master
 
Join Date: Mar 2002
Location: upstate New York
Posts: 1,364
Trader Rating: 21 (100%+)
Default Bearings

Remington makes a drilube for guns.It has teflon,spray it on and it dries.Doesn't attract dirt or carpet fibers.Works great.Smoooth!Mario.
lotus1 is offline   Reply With Quote
Old 12-24-2004, 06:40 AM   #9932
Tech Apprentice
 
Jay Boyd's Avatar
 
Join Date: Jan 2004
Location: Canada
Posts: 95
Default BRP's top plate.

These work mint.(For us damper disc users)
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=2565&item=59453935 90&rd=1
Jay Boyd is offline   Reply With Quote
Old 12-24-2004, 07:34 AM   #9933
Tech Master
 
Rob Phillips's Avatar
 
Join Date: Nov 2004
Location: Indianapolis / VA
Posts: 1,722
Trader Rating: 6 (100%+)
Default

Just remeber that WD-40 is not a lubricant so to speak. It's actually a water displacer/de-greaser. Use it to clean you parts/bearings then use a lubricant.
Rob Phillips is offline   Reply With Quote
Old 12-24-2004, 07:39 AM   #9934
Tech Master
 
Rob Phillips's Avatar
 
Join Date: Nov 2004
Location: Indianapolis / VA
Posts: 1,722
Trader Rating: 6 (100%+)
Default

for your rear bearing that are seeing the lateral load (like a thrust bearing) I have found that soaking them in Mobil 1 has given them a little more life. I have heard some where that someone has found a thrust bearing or something similar for use on our rear axles. any word?
Rob Phillips is offline   Reply With Quote
Old 12-24-2004, 07:43 AM   #9935
Tech Fanatic
 
primusblowsgoat's Avatar
 
Join Date: Jul 2004
Location: Pingree Grove, IL
Posts: 987
Trader Rating: 14 (100%+)
Send a message via AIM to primusblowsgoat Send a message via Yahoo to primusblowsgoat
Default

jayboyd, where does that extra standoff bolt to? i cant quite figure it out
__________________
Schumacher Racing
Schumacher Cat SX2
Schumacher Cougar SV
primusblowsgoat is offline   Reply With Quote
Old 12-24-2004, 07:45 AM   #9936
Tech Fanatic
 
primusblowsgoat's Avatar
 
Join Date: Jul 2004
Location: Pingree Grove, IL
Posts: 987
Trader Rating: 14 (100%+)
Send a message via AIM to primusblowsgoat Send a message via Yahoo to primusblowsgoat
Default

ron, slapmaster or whatever his screen name is makes that thrust bearing, he says hes been running the same diff for like 14 months or something crazy like that and its still smooth.

he charges 30 bucks for everything you need i believe
__________________
Schumacher Racing
Schumacher Cat SX2
Schumacher Cougar SV
primusblowsgoat is offline   Reply With Quote
Old 12-24-2004, 07:47 AM   #9937
Tech Apprentice
 
Jay Boyd's Avatar
 
Join Date: Jan 2004
Location: Canada
Posts: 95
Default

It goes right to the t-plate mount.
Here it is on Barry Baker's car at Cleveland.
Attached Images
File Type: jpg 110-1006_img.jpg (186.3 KB, 543 views)
Jay Boyd is offline   Reply With Quote
Old 12-24-2004, 07:48 AM   #9938
Tech Fanatic
 
primusblowsgoat's Avatar
 
Join Date: Jul 2004
Location: Pingree Grove, IL
Posts: 987
Trader Rating: 14 (100%+)
Send a message via AIM to primusblowsgoat Send a message via Yahoo to primusblowsgoat
Default

ahh, that makes sense now
__________________
Schumacher Racing
Schumacher Cat SX2
Schumacher Cougar SV
primusblowsgoat is offline   Reply With Quote
Old 12-24-2004, 07:57 AM   #9939
Tech Apprentice
 
Jay Boyd's Avatar
 
Join Date: Jan 2004
Location: Canada
Posts: 95
Default

An up-side down pic.
Attached Images
File Type: jpg pod.jpg (39.7 KB, 464 views)
Jay Boyd is offline   Reply With Quote
Old 12-25-2004, 02:17 PM   #9940
Tech Apprentice
 
Quietroit's Avatar
 
Join Date: Jul 2004
Location: Smithfield, Va
Posts: 66
Default crc 3.1

what is a good starting setup for 100x50 carpet. For a Chameleon pro and Monster Horsepower Stock Pro. I have a crc 3.1
Quietroit is offline   Reply With Quote
Old 12-25-2004, 04:54 PM   #9941
Tech Champion
 
tony montana's Avatar
 
Join Date: Aug 2002
Location: Leonardtown Md.
Posts: 6,025
Trader Rating: 65 (100%+)
Default

I also need a carpet setup for a yrx12, Im running it all stock right now, Also I was looking at some of the l3 carpet setups, what is stagger? Also another question, with my car off the ground is the rear pod supposed to be on a angle from the chassis?
__________________
K.C. Guy- Tekno rc - Lunsford Racing- FTM Grip
tony montana is offline   Reply With Quote
Old 12-25-2004, 05:19 PM   #9942
Tech Master
 
lazyboy's Avatar
 
Join Date: Jun 2003
Location: Franklin,WI
Posts: 1,536
Send a message via AIM to lazyboy
Default

Quote:
Originally posted by tony montana
I also need a carpet setup for a yrx12, Im running it all stock right now, Also I was looking at some of the l3 carpet setups, what is stagger? Also another question, with my car off the ground is the rear pod supposed to be on a angle from the chassis?
which way is it angled?
__________________
Random Guy
FT B4
Sponsored by Axiom Motors
Trackside hobbies
lazyboy is offline   Reply With Quote
Old 12-25-2004, 11:16 PM   #9943
Tech Master
 
ghoppa's Avatar
 
Join Date: Dec 2003
Location: Sin City - Las Vegas
Posts: 1,666
Trader Rating: 48 (98%+)
Default

anybody know who makes the antenna that allows you to "feed" the receiver waire "through" it rather than "sprial" it around the ones that comes in the L4 kit????

I have seen several cars with it, and I would like one too....
ghoppa is offline   Reply With Quote
Old 12-25-2004, 11:21 PM   #9944
Tech Elite
 
odpurple's Avatar
 
Join Date: Dec 2002
Location: San Francisco
Posts: 2,187
Default

Quote:
Originally posted by ghoppa
anybody know who makes the antenna that allows you to "feed" the receiver waire "through" it rather than "sprial" it around the ones that comes in the L4 kit????

I have seen several cars with it, and I would like one too....
That's the Paragon Pro Stick antenna. It's hollow graphite, works great. Part #77090, the only place I've been able to find it is Tower Hobbies. The mount that it comes with isn't right for 1/12th scale, but you can easily cut it off and install it in a drilled out 1/12th mount.
O'D
odpurple is offline   Reply With Quote
Old 12-26-2004, 10:47 AM   #9945
Tech Master
 
nmt6789's Avatar
 
Join Date: Jan 2003
Location: Long Island NY
Posts: 1,292
Send a message via AIM to nmt6789
Default

Does anyone have the airtronics 94145 servo in their 12L4? i just got a 12l4 and the servo doesnt fit....
nmt6789 is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 9 (2 members and 7 guests)
hydro111, TOADYY
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 09:27 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0