R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 12-10-2004, 04:57 PM   #9706
Tech Regular
 
Join Date: Nov 2003
Location: North Wales, PA
Posts: 352
Default

Hey guys! back again to rant and rave... Well I soon figured out that the flanged bearings that come with CRC's car for the rear and (CRC Carpet Knife 3.2R) absolutely SUCK a big one... Really gritty.. What are the best bearings to get??

Diff Balls: Should I invest in ceramics?

Anyway, to get to the point of this post... My rear pod slides back and fourth 2-3 mm and I narrowed it down to the ball that connects it in the middle of the chassis... I cannot get it tight at all.. How are you to tighten that down but yet keep it free?

If you dont think that is what is causing the wiggling, please post back! Thanks
FriedDiff is offline   Reply With Quote
Old 12-10-2004, 04:58 PM   #9707
Tech Regular
 
Join Date: Nov 2003
Location: North Wales, PA
Posts: 352
Default

Quote:
Originally posted by theisgroup
i beleive the crc are 4 cell in side by side config.
Correct
FriedDiff is offline   Reply With Quote
Old 12-10-2004, 05:00 PM   #9708
Tech Master
 
rcgen's Avatar
 
Join Date: Feb 2004
Location: Jacksonville, FL
Posts: 1,069
Default

Is there a website for CRC?
rcgen is offline   Reply With Quote
Old 12-10-2004, 05:01 PM   #9709
Tech Regular
 
Join Date: Nov 2003
Location: North Wales, PA
Posts: 352
Default

http://teamcrc.com
FriedDiff is offline   Reply With Quote
Old 12-10-2004, 05:15 PM   #9710
Administrator
 
Matt M.'s Avatar
R/C Tech Elite Subscriber
 
Join Date: Aug 2001
Posts: 8,308
Trader Rating: 25 (100%+)
Default

Quote:
Originally posted by lazyboy
doses anyone have any pictures of a cefx car that they are willing to post.


thanks lazy
come to green bay there will be two there....
Matt M. is offline   Reply With Quote
Old 12-10-2004, 05:40 PM   #9711
Tech Master
 
lazyboy's Avatar
 
Join Date: Jun 2003
Location: Franklin,WI
Posts: 1,536
Send a message via AIM to lazyboy
Default

Quote:
Originally posted by mr. losi
come to green bay there will be two there....

i would but it wouldnt be worth the trip two see two cars since im not able to race.
__________________
Random Guy
FT B4
Sponsored by Axiom Motors
Trackside hobbies
lazyboy is offline   Reply With Quote
Old 12-10-2004, 06:19 PM   #9712
Tech Regular
 
Join Date: Nov 2003
Location: North Wales, PA
Posts: 352
Default

Quote:
Originally posted by ME
Hey guys! back again to rant and rave... Well I soon figured out that the flanged bearings that come with CRC's car for the rear and (CRC Carpet Knife 3.2R) absolutely SUCK a big one... Really gritty.. What are the best bearings to get??

Diff Balls: Should I invest in ceramics?

Anyway, to get to the point of this post... My rear pod slides back and fourth 2-3 mm and I narrowed it down to the ball that connects it in the middle of the chassis... I cannot get it tight at all.. How are you to tighten that down but yet keep it free?

If you dont think that is what is causing the wiggling, please post back! Thanks
FriedDiff is offline   Reply With Quote
Old 12-10-2004, 06:43 PM   #9713
Tech Master
 
Join Date: Jul 2003
Location: Wisconsin
Posts: 1,202
Trader Rating: 21 (100%+)
Default

fried diff- Did you try and spray out your bearings and then relube them with thin oil? What part can't you get tight? Is it the 4-40 screw that screws into the ball or the 2-56 screws in the socket?

Preston-check out the Snowbirds race page on the 1st page of RC tech. There should be a couple of pictures of Ron Atomic's car in there.
__________________
Thanks to pops

TLR, Fantom, Horizon, Spektrum, Trackside
Brian L is offline   Reply With Quote
Old 12-10-2004, 06:53 PM   #9714
Tech Master
 
JamesArluck's Avatar
 
Join Date: Jul 2003
Posts: 1,232
Trader Rating: 52 (100%+)
Send a message via AIM to JamesArluck
Default

Quote:
Originally posted by FriedDiff
Best Bearings- I've had really good luck with the rc4less ceramics. A little expensive but they spin really free and last a long time. For the outer hub (thrust) bearing in the diff you may just want to buy a bunch of cheap ones, since you will be changing those regularly.

I'm trying ceramic diff balls right now (also from RC4less) and are really liking them. Super smooth and a long time between rebuilds. I've heard rumors that ceramic balls shorten the life of the rings, but I haven't seen any of that yet. The cost is quite a bit more expensive than normal steel balls, so you have to decide if the extra cost is worth it to you.

If you're having troubles tightening up the pivot ball to it's socket using the 2-56 screws you can sand a little material off of the bottom socket where it touches the top one. Be careful not to remove too much or the pivot ball will bind.

-James
JamesArluck is offline   Reply With Quote
Old 12-10-2004, 07:26 PM   #9715
Tech Master
 
lazyboy's Avatar
 
Join Date: Jun 2003
Location: Franklin,WI
Posts: 1,536
Send a message via AIM to lazyboy
Default

Quote:
Originally posted by Brian L
Preston-check out the Snowbirds race page on the 1st page of RC tech. There should be a couple of pictures of Ron Atomic's car in there.
thanks brian
__________________
Random Guy
FT B4
Sponsored by Axiom Motors
Trackside hobbies
lazyboy is offline   Reply With Quote
Old 12-10-2004, 07:37 PM   #9716
Tech Master
 
dakrat's Avatar
 
Join Date: Nov 2004
Location: 96th ABW
Posts: 1,581
Default

quick question before i order online.


will trc front tires fit the rc12l3? i know the crc tires dont.
dakrat is offline   Reply With Quote
Old 12-10-2004, 07:51 PM   #9717
Super Moderator
 
Kraig's Avatar
 
Join Date: Aug 2001
Location: Sun Prairie, WI
Posts: 6,275
Trader Rating: 69 (100%+)
Default

Lazy, check out the website for CEFX. Just click here.
__________________
There is great need for a sarcasm font.

You never know when it will strike, but there comes a moment at work when you know that you just aren't going to do anything productive for the rest of the day.

Sometimes I post just to look at my avatar.
Kraig is offline   Reply With Quote
Old 12-10-2004, 08:13 PM   #9718
Tech Addict
 
JohnB's Avatar
R/C Tech Charter Subscriber
 
Join Date: Aug 2002
Location: Oregon City, Or
Posts: 674
Trader Rating: 1 (100%+)
Default

Quote:
Originally posted by dakrat
quick question before i order online.


will trc front tires fit the rc12l3? i know the crc tires dont.
CRC tires work, I'm running some now, you just need to space them a little different. For TRC tires you will need to get some flanged bearings.


take care
john
JohnB is offline   Reply With Quote
Old 12-10-2004, 08:16 PM   #9719
Tech Master
 
dakrat's Avatar
 
Join Date: Nov 2004
Location: 96th ABW
Posts: 1,581
Default

john, so only jaco tires are direct fit?
dakrat is offline   Reply With Quote
Old 12-10-2004, 08:16 PM   #9720
Tech Master
 
whynot's Avatar
 
Join Date: May 2003
Posts: 1,481
Trader Rating: 18 (100%+)
Default

Quote:
Originally posted by FriedDiff
Hey guys! back again to rant and rave... Well I soon figured out that the flanged bearings that come with CRC's car for the rear and (CRC Carpet Knife 3.2R) absolutely SUCK a big one... Really gritty.. What are the best bearings to get??

Diff Balls: Should I invest in ceramics?

Anyway, to get to the point of this post... My rear pod slides back and fourth 2-3 mm and I narrowed it down to the ball that connects it in the middle of the chassis... I cannot get it tight at all.. How are you to tighten that down but yet keep it free?

If you dont think that is what is causing the wiggling, please post back! Thanks
FriedDiff
I have a brand new T_Fource and it does the same thing.I bought some irs tplate balls and some new associated plastic pieces that tighten around the balls.I am hoping that it works will find out tomorrow.
mike
whynot is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 03:17 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0