R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 12-30-2003, 09:27 PM   #5911
Tech Master
 
Bobby Z's Avatar
 
Join Date: Sep 2001
Location: Niagara Falls, Ontario, Canada
Posts: 1,117
Trader Rating: 4 (100%+)
Default Quad 12 Setup

Adam

Thanks for the setup. Not too much difference.

I will be ordering the spring steel t-plate next week. I have to pick up a lathe first, later this week, since I sold mine last year.

Did you notice much difference between the steel t-plate and the fiberglass?

thanks again
Bobby Z is offline   Reply With Quote
Old 12-30-2003, 09:29 PM   #5912
Tech Addict
 
Join Date: Nov 2003
Location: Ridin my Harley
Posts: 707
Trader Rating: 3 (100%+)
Send a message via AIM to Adam Hartzell
Default

The spring steel is the best thing out there. The only problem is if you hit anything it takes a corner or two to reset itself.
Adam Hartzell is offline   Reply With Quote
Old 12-30-2003, 09:51 PM   #5913
Tech Regular
 
DPowell's Avatar
 
Join Date: Apr 2003
Location: Denver, CO
Posts: 454
Trader Rating: 3 (100%+)
Default

Quote:
Originally posted by jswinkos

One question, do the batteries fit snuggly or do u guys put something (like foam tape) on the bar to hold them.
For the most part, the batteries fit pretty snug. As with everything, there are slight variations that effect the fit.

D.P.
__________________
www.powellracingcomponents.com
**Record setting carbon fiber**

Speedmerchant and TOP USA dealer.
DPowell is offline   Reply With Quote
Old 12-31-2003, 07:40 AM   #5914
Registered User
R/C Tech Charter Subscriber
 
Join Date: Oct 2003
Posts: 370
Thumbs up Thanks Matt and Rice

I'll try it again tonight.
Demetris Taylor is offline   Reply With Quote
Old 12-31-2003, 07:47 AM   #5915
Tech Champion
 
TimPotter's Avatar
 
Join Date: Sep 2001
Location: Boynton Beach Fl > Randoph NJ
Posts: 7,481
Trader Rating: 14 (100%+)
Send a message via AIM to TimPotter
Default

Doug, I recently got the Quad kit for my Yokomo, I cant wait to put it togther, very nice workmanship. Hector and Jerry keep on singing the praises of the car...
__________________
Clean Title & Escrow|p3|TRF|Tamiya|SerpentAmerica|FSEARA|Team Butter|RC 3|Munno |RCTECH #29|EAMotorsports|BMI|Novak|SpeedPassion|RadioPost
TimPotter is offline   Reply With Quote
Old 12-31-2003, 12:02 PM   #5916
Tech Elite
 
trackdesigner71's Avatar
 
Join Date: Sep 2002
Location: Lynchburg/Portsmouth, VA
Posts: 4,978
Trader Rating: 4 (100%+)
Send a message via AIM to trackdesigner71 Send a message via Yahoo to trackdesigner71
Default RC12L question

Hey Im getting an old RC12L from a guy. DO any of the parts from teh later 12L series cars (12LC and 12L3) fit it? Do any of the newer bodies fit it?
trackdesigner71 is offline   Reply With Quote
Old 12-31-2003, 12:41 PM   #5917
che
Tech Regular
 
che's Avatar
 
Join Date: Aug 2001
Location: Niagara Falls, Ontario
Posts: 291
Default

Adam Hartzell,

You are in Michigan, do you race at Larry's?
We are having a big trophy race up here in St. Catharines/Niagara Falls at the end of February.

Dan @ Larry's will be posting the form up there this week.
Or you can grab it HERE

Come run your Quad with BobbyZ and myself....

(About 3 hours drive from Larry's)
che is offline   Reply With Quote
Old 12-31-2003, 02:22 PM   #5918
Tech Addict
 
Join Date: Nov 2003
Location: Ridin my Harley
Posts: 707
Trader Rating: 3 (100%+)
Send a message via AIM to Adam Hartzell
Default

che-- Count me in. I really don't know much about tuning 19's so I will probably run stock. I'll try to bring a few others with me. Any Idea on the cost for the hotel.
Adam Hartzell is offline   Reply With Quote
Old 12-31-2003, 02:29 PM   #5919
Tech Addict
 
Join Date: Nov 2003
Location: Ridin my Harley
Posts: 707
Trader Rating: 3 (100%+)
Send a message via AIM to Adam Hartzell
Default

After looking up directions its about 5 hours or so for me and I'm only 15 min. from Larry's. I'll have to see if I can get the time off of work for that.
Adam Hartzell is offline   Reply With Quote
Old 12-31-2003, 04:57 PM   #5920
P2
Tech Fanatic
 
P2's Avatar
 
Join Date: Aug 2003
Location: Oahu, Hi
Posts: 865
Trader Rating: 15 (100%+)
Default Re: RC12L question

Quote:
Originally posted by trackdesigner71
Hey Im getting an old RC12L from a guy. DO any of the parts from teh later 12L series cars (12LC and 12L3) fit it? Do any of the newer bodies fit it?
The 12L series of cars have not changed for many years. Its basic layout is the same and all the new parts will fit on the old chassis. Some actually prefer the old style front end....and yes all the bodies will fit!!
__________________
TopRacingUSA | Team EPIC | Thunder Power | OD Racing
P2 is offline   Reply With Quote
Old 01-01-2004, 11:16 AM   #5921
Tech Initiate
 
Join Date: Nov 2003
Location: Montreal, Canada
Posts: 37
Default Front Axles

This may seem like a silly question, but I haven't raced 1/12th in ages.

Does everybody still run the trailing front axle or are you now running the in-line?

I see the Yok has offset axles for the in-line blocks, so it got me to wondering...
pilmat is offline   Reply With Quote
Old 01-01-2004, 11:29 AM   #5922
Tech Apprentice
 
rattlr2's Avatar
 
Join Date: Dec 2003
Posts: 91
Trader Rating: 3 (100%+)
Default

anyone know where i can get carbide cutter for cobra tire lathe the ac model
rattlr2 is offline   Reply With Quote
Old 01-01-2004, 03:50 PM   #5923
Tech Master
 
=MisFitz= NuKe's Avatar
 
Join Date: Apr 2003
Posts: 1,058
Send a message via AIM to =MisFitz= NuKe Send a message via Yahoo to =MisFitz= NuKe
Default

alright, I finished my new 12. Ill post some pics later, to see what you guys think.

hmm, hey P2, you have a body I could run for this weekend?
=MisFitz= NuKe is offline   Reply With Quote
Old 01-01-2004, 07:51 PM   #5924
Tech Prophet
 
Randy Caster's Avatar
R/C Tech Elite Subscriber
 
Join Date: Mar 2003
Location: Irvine, CA
Posts: 16,665
Trader Rating: 45 (100%+)
Default

Quote:
Originally posted by =MisFitz= NuKe
alright, I finished my new 12. Ill post some pics later, to see what you guys think.

hmm, hey P2, you have a body I could run for this weekend?
What car did ya chose?
Randy Caster is offline   Reply With Quote
Old 01-01-2004, 08:51 PM   #5925
Tech Fanatic
 
Join Date: Mar 2002
Location: Indianapolis, IN
Posts: 864
Default

pilmat - everyone uses the offset front axle except in oval.
davidl is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 03:36 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0