R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 09-21-2017, 01:26 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: DesertRat
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time. On black carpet the car may be numb to sauce changes, either a long or short sauce can produce very similar handling.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front. Alternatively you can sauce the front tires harder and tune the car for less front end bite.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz. Possibly a longer sauce will prevent fuzzing.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Rear - Green and Blue (BSR) or Green and Light Blue (JFT)
Front - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
DISCONTINUED 1S ESC:
If there are any missing please add them!!


If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!

Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:
Pan Car Front Suspension Tuning:
DISCLAIMER : The following tuning advice was written based on the tuning experience of the author and may not hold true for all cars, drivers, or surfaces. In the end the best tuning advice is to experiment and make changes one at a time so you can track your changes and find the car balance that works best for your driving style. One real world test is worth a million ‘expert’ opinions.

Front End Type:

All popular modern pan car front suspensions are very similar, with a few exceptions such as Speedmerchant New School but most of the info in this wiki applies to them as well. For the most part, they consist of a rigid bottom arm, an upper A-arm, and a kingpin with a spring. There are different flavors of this general design, such as the CRC Dynamic Strut that uses a threaded kingpin and upper pivot ball instead of the Associated style that uses a kingpin that goes through the entire steering knuckle assembly, but their operation is the same with the rigid lower arm and the upper arm controlling the arc of movement as the suspension is compressed.

Assembly:

More so than in almost any other part of the car, the front suspension of your 1/12 car must move absolutely free. Reamers and hobby knives are important here, as any binding will cause the car to corner unpredictably. A little play in the suspension is a good thing, and racers will often find that ‘worn in’ suspension pieces function a little better than new.

Springs:

Besides tires, spring rate is the most important part of deciding how your car will handle through corners, but are somewhat complicated. As a general rule of thumb, a very hard front spring will have somewhat less steering grip than a softer spring with the same suspension setup and tires, but not as much as in other classes such as touring or offroad. On carpet, springs of different tension can be used to tune how your car will maintain or lose energy through corners with the following general rule of thumb:

Hard Spring (0.55mm or harder): Less overall steering, quick reaction to driver input, less on power steering, harder turn-in with potentially lazy mid-corner and exit.

Soft Spring (.45mm): More overall steering especially at low speed, slightly slower reaction to driver input, more on-power steering, less aggressive turn-in but can ‘hook’ and give better mid-corner and exit.

It is worth noting that front springs from different suppliers are often very different, in both height, wire thickness, and coils for a given spring height meaning that a “medium” spring from one manufacturer may be the “hard” spring for another. To make accurate changes you may want to use one spring maker and stick with their line.

Another aspect to pan car springs is that they can get “blown out” and collapse, no longer as stiff or as tall as they were. These should be replaced with fresh springs to ensure consistent handling.

Dampening:

This is generally a minor adjustment, but adding dampening tube fluid to the front kingpins of a 1/12 car can give it a little more initial steering. Often unusual compounds see use here, such as Losi Smart Diff Grease or Associated Green Slime being a popular front kingpin lube.

Caster and Reactive Caster:

Caster is the angle of the kingpin, almost always angling back to the rear of the car, with a typical range from 0-10 degrees. Increasing your caster will typically result in less turn-in but a little more control, more steering exiting the corner, and somewhat increased straight-line stability with less tendency to wander because a wheel running caster will tend to straighten itself. Less caster will usually give you more off-power steering, but often with correspondingly less on-power when accelerating out of the corner.

Running reactive caster attempts to use both of these aspects to increase overall steering: when the car loads up on the outside front tire, the caster angle decreases, increasing the front end ‘hook’ as you enter the corner and then giving you the high caster on-power steering as you exit and weight is transferred off the front end. More reactive caster means more overall steering, but can mean you may have to adjust your driving style to drive more ‘ahead of the car’, needing to predict where the front end will grip.

As grip increases, less reactive caster is the normal tuning change made to keep the front end of the car from gripping too hard and oversteering and prevent traction roll. Static caster adjustments are still used to change the cars on power / off power steering balance.

Reactive Camber and Front Roll Center:

Reactive camber or camber gain is how much camber is added the front wheels as the suspension compresses. This can be increased or decreased by changing the angle and length of the top arm. Short, angled arm = more. Long, flat arm = less. More reactive camber will typically cause the car to “roll up” on the outer front wheel, transferring more weight in a turn and give more steering up to the point at which the tire is overloaded. This is generally more front grip and weight transfer than wanted on carpet, and as a result most cars run a flatter longer front arm.

Roll Center is the point on which the car will twist laterally or ‘roll’ during cornering. This can be raised or lowered by changing the angle and length of the top arm, with a short angled arm raising is slightly and a long flat arm lowering it. From what I have calculated most modern 1/12 cars meant for carpet have a roll center somewhere around the height of the chassis plate or just below it, but due to the lower arms being rigid and flat the roll center cannot be under the bottom of the tires like it often is on a touring car.
These two are inexorably linked in pan cars. Top arm length can be changed by the top arm mount in or out using shims or a CRC Long Arm kit, but is generally a minor tuning choice. Tuning of roll center with shims is usually a minor tuning choice in a pan car with a rigid bottom arm due to how the car cannot gain extra mechanical advantage on the lower arm as you can in a touring car, while reactive camber can be a significant driver of the car’s performance. In a modern car running on carpet the kit setup is usually perfectly fine.

Front End Alignment:

Static camber is the angle of your front wheels at rest, typically somewhere from 0 to 1.5 degrees on a pan car depending on surface, tire choice, and other factors, but a good starting point is usually somewhere around 0.5 degrees. More camber will typically give more steering, but many racers use static camber to ensure that their tires wear flat even if that means not having exactly equal camber on both sides of the car. This is adjusted by threading in and out the upper turnbuckle or pivot ball.

It is also worth noting that when running on high grip the flex and deformation of your chassis, suspension parts, and front wheels can become significant and cause uneven front tire wear. Some troubleshooting of the right combination of static camber, camber gain, caster, and tire/rim choice may be necessary to ensure even front tire wear.

Toe-In:

The front toe is one of the more easily adjusted aspects of the car and can have a significant effect on the attitude of the car due to it being a quick way to moderately adjust Ackerman without making significant other changes. With nothing else being adjusted, going from zero toe to toe-in will give a car a harder turn-in and will tend to scrub speed with the front end as opposed to using drag brake. This can be necessary when racing in Super Stock or higher power classes and will allow you to drive more aggressively, and can help the car track straighter under power. Toe-out will tend to make the car coast more through corners due to reducing the steering angle of the outer front tire. If a car has too much off-power steering but is otherwise stable, adding toe-out can calm the car but may the car to wander on the straights especially if the front end setup is very soft.

Ackerman:

Ackerman is the difference in steering angle between the two front tires during a turn. It is the result of how during a turn the inside of the car experiences a tighter circle and needs correspondingly more steering angle, but is also an important tuning tool. More Ackerman means having more inside wheel steering angle relative to the outer wheel, less means that the difference in steering angle is smaller.

To add or remove Ackerman, using a servo horn that spaces the links further apart (such as a Kimbrough Small Servo Saver, the outer holes on a Tamiya or Xray servo saver) will have more Ackerman than a servo that puts the links close together (Kimbrough Medium inner holes, Tamiya or Xray inner holes.) The rule of thumb is that a servo that puts the ball studs close together but spaced away from the servo horn will have less Ackerman than one that spaces them far apart and close to the servo horn. Ackerman changes will have the same effect as changing toe with more Ackerman being effectively toeing the wheels out and less toeing them in, but will not affect the straight-line attitude of the car.

Turning Circle / Steering Angle:

In offroad or even touring car you can set up the car to use the full angle of the steering 100% of the time. You will almost certainly not be able to do this in 1/12 scale. It goes without saying that as you turn up your steering angle you will gain steering often to the point of the car being undriveable. The quickest way to set the steering correctly is to set the sub-trim in your radio such that the car tracks straight and the servo horn is straight up and down, then set the endpoints equally such that they don't quite hit the steering bump-stops, then turn down the dual-rate or total throw from there. A typical starting point is somewhere between 45 and 60% of the total steering throw, or a 4-5' turning circle.
Pan Car Rear Pod Tuning:
Modern pan cars are all link cars with a center pivot ball and solid rear axle. This suspension system is required by ROAR rules and has the advantage of being simple, lightweight, and inexpensive compared to other more exotic methods of rear suspension, but it has some complicated movements that can be unintuitive.

Motion of the Rear Pod:

Due to how the rear pod is a solid axle, the only motion the pod itself sees is the main pivot up and down, but due to the main chassis being independently sprung it will feel the lean, dive, and squat of the main chassis as the car is driven. The lateral forces of the main chassis during cornering is transmitted through the main pivot ball and side links, the roll through the side springs and side dampeners, and the squat and dive through the main shock and spring. In addition, the torque of the motor against the pinion gear both during acceleration and braking is significant enough to cause a change in attitude even in low-powered classes. The motor pinion will try to “climb” the spur gear, lifting the center pivot of the car and countering the “squat” of the main chassis weight being transferred backward by the acceleration or the opposite under brakes.

Main Shock:

The adjustment of the main shock of a pan car is one of its more important tuning parameters. Spring, dampening oil, and pod droop are all controlled by the main shock.

Main Spring:

A soft main spring generally means more rear grip and more forgiving off-power, while a stiffer spring can mean more steering especially off-power, but the main spring must also be stiff enough to prevent the chassis from dragging when running on high grip. For most cars the kit spring is a medium weight spring that is a good starting point.

Main Shock Dampening:

The weight of the main shock oil will determine how fast the car will react off-power. 30wt or roughly 300cps shock oil is a good starting point, going up in weight will increase initial off-power turn-in, while going down will generally make initial turn-in softer. Often a heavier shock oil can make the car transition from entry to mid to corner exit smoother, where a car with light fluid may have a more pronounced ‘hook’ in the mid corner.

Side Springs:

The side springs transfer the roll motion of the main chassis to the rear plate via spring tension. Softer side springs give the car more rear grip and can make the car have a smoother steering feel. Stiffer springs promote the cars rotation and give more steering. You can either pre-load side springs or let them float, due to all side springs being progressive beehive shaped springs pre-load makes them effectively harder and will give more steering, but a small amount of pre-load can also make the care more predictable and forgiving. In conditions of extremely high grip, it may be possible to run no side springs at all due to the steering afforded by the tacky running surface and helps prevent traction-roll, likewise in extremely low grip when rear stability is absolutely necessary. Generally 1/12 cars run soft side springs but stiffer ones can be very common in Pro 10, WGT, or WGT-R.

Side Dampener Tubes:

Heavier tube lube will keep a car flatter at corner entry, initiating quicker. It may also make the car square off the corner entry when the grip gets beyond med-high. Going lighter will reduce steering initiation and maybe preferred on higher grip. This parameter is really unique to the driver preference, as some drivers are very fast and consistent with heavily dampened cars while others prefer softer setups.

Droop:

Controlled by the length of the shock, adjusting the rear pod droop is extremely important on high-grip surfaces. Reducing droop prevents the car from transferring weight during cornering and will give more rear stability and prevent traction-roll or problematic lifting of the inside rear tires during cornering, low droop can also give the car slightly more on-power steering. Increasing will allow the car to transfer more weight and dive harder into corners, but by allowing the center of the car to rise you will be more prone to traction roll issues. A typical starting point is 1-2mm of droop from ride height, but 0mm is often used on high grip.

Print Wikipost

Like Tree62Likes
Reply
 
Thread Tools Search this Thread
Old 09-10-2010, 04:59 AM   #34456
Tech Regular
 
GWH74's Avatar
 
Join Date: Jan 2009
Location: Adelaide
Posts: 254
Trader Rating: 13 (100%+)
Default

Futaba S9650 Mini Servo. Just cut the wings off and it is a perfect fit.
You will need a different servo save then comes with the 12r5.1 kit.
Kimbrough #114 is the one you need
__________________
AE 12R5.1 - Custom chassis
For Sale BMI DB12RR, Tire Warmers and lots of other stuff.
GWH74 is offline   Reply With Quote
Old 09-10-2010, 10:16 AM   #34457
Tech Adept
 
Join Date: Jun 2006
Location: Florida
Posts: 216
Default New to 1/12th Scale

Hello everyone,

I'm very interested in getting into 1/12th scale racing, on both carpet and asphalt. I have a lot of questions though, and need lots of help. I'm sure there have been people posting asking for help just as I am but...with nearly 2300 pages in this forum I'm not about about to go sifting.
Anyways let me first say that I've raced 1/10th scale nitro touring cars for about 5 years, and recently have taken a break for a couple years, so I do know some stuff. I just need help getting into 1/12th scale.
One of the first things I need major help on is tires. In nitro racing, there weren't color coded tire shores, just numbers. What do all the colors mean, and what is best for certain surfaces? Also, I obviously want to be competitive and start out with a good car. What cars seem to be the most successful lately? Are there any new models coming out soon that I should wait for? I don't want to start out with something that's getting replaced real soon with a new model. Also, I'd appreciate it if you could just throw around some opinions about motors/batteries/speed controls/etc. I guess this is all I'll post for now, and I'll ask more questions as they come to me. Your help with any of my questions would be greatly appreciated.
Luke W is offline   Reply With Quote
Old 09-10-2010, 02:22 PM   #34458
Tech Master
 
andrew-01's Avatar
 
Join Date: Mar 2007
Location: SOCAL
Posts: 1,210
Trader Rating: 22 (100%+)
Default

Quote:
Originally Posted by Luke W View Post
Hello everyone,

I'm very interested in getting into 1/12th scale racing, on both carpet and asphalt. I have a lot of questions though, and need lots of help. I'm sure there have been people posting asking for help just as I am but...with nearly 2300 pages in this forum I'm not about about to go sifting.
Anyways let me first say that I've raced 1/10th scale nitro touring cars for about 5 years, and recently have taken a break for a couple years, so I do know some stuff. I just need help getting into 1/12th scale.
One of the first things I need major help on is tires. In nitro racing, there weren't color coded tire shores, just numbers. What do all the colors mean, and what is best for certain surfaces? Also, I obviously want to be competitive and start out with a good car. What cars seem to be the most successful lately? Are there any new models coming out soon that I should wait for? I don't want to start out with something that's getting replaced real soon with a new model. Also, I'd appreciate it if you could just throw around some opinions about motors/batteries/speed controls/etc. I guess this is all I'll post for now, and I'll ask more questions as they come to me. Your help with any of my questions would be greatly appreciated.

Tire color codes:
http://www.rctech.net/forum/attachme...th_foam_10.gif
__________________
ANDRXW.com
andrew-01 is offline   Reply With Quote
Old 09-10-2010, 03:30 PM   #34459
Tech Initiate
 
Join Date: Oct 2007
Location: Billings, MT
Posts: 32
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by Luke W View Post
Hello everyone,

I'm very interested in getting into 1/12th scale racing, on both carpet and asphalt. I have a lot of questions though, and need lots of help.....
I'd suggest starting with a car that is similar (or at least common) to what others at your club will be racing with. It will make it easier to get help or flesh out setup problems that you might run into. 12th scale can be finicky, sometimes something really small will make a big difference.

CRC GenXL and Associated 12R5 are pretty common and definitely competative. BMI with the old school front end is pretty straight forward for someone to help you with. Speedmerchant with the old front end is again straight forward. The newer front ends might be harder to help you with until people have them figured out a bit better.

Tekin RS speed control is common and pretty well sorted out (probably go with the RS / Tekin motor combo that is correct for the class that you'd be running, i.e. 17.5 or 13.5). I'm going with the new Novak Kinetic 1S and Ballistic combo but it isn't as well sorted out yet since the Kinetics are pretty new. The AE Black Diamond is interesting. It is really spendy and isn't computer programmable (has to be sent to the factory for firmware upgrades), but it's finite settings (have a handful of "profiles" for the various functions) might be, in a way, easier to setup and it is unquestionably fast. I'm not necessarily suggesting it, but it might be worth putting in your research queue.

Servo, Futaba 9650 or JR 3650 are the tops of my lists.

Thunderpower packs are well thought of 5000+MAh 50c (although I went with a budget pack from Protek 5000MAH 40c for less $ as I don't think I'll notice or need the 50c rate running 17.5). SMC and others make great packs too, probably won't go wrong if you just do a little research before buying. These are 1S LiPo hard case, but you probably already get that.

Depending on class, you'll want pinion / spurs capable of 60-100mm rollout. Plan to get a bunch of pinions, probably from about 40-60 tooth and a couple spurs 76,80,84 (car will probably come with 88). If you can do some research on your motor / class (ESC rules, sportsman or open) / track size, you can probably slim those down to maybe 2 spurs and a dozen pinions.

Hit up gearchart.com to make rollout charts. Tires will probably be cut and then worn down from about 46mm to 42mm. Consider a tire truer although your club or other members will likely let you use their's and they aren't cheap.

Receiver will be preferably something small but in the end depends on your radio.

Some people are using a voltage booster and some a receiver pack since 1S Lipo is 3.7v and that isn't really enough for stable receiver / servo operation. Take your pick there, I'm going with a small 220MAh 2S LiPo receiver pack from Protek.

Depending on car, front and center springs, tube lube (I'm using Shur Lube), shock oils (Losi or AE but stick to one brand) for tuning. Tire sauce (check what your track uses / allows). Diff lube, bearing oils, etc there (you probably have some of this, just thinking out loud). Camber gauge (RPM works fine and is cheap / simple), ride height gauge (I prefer non-stepped), front end alignment tools (I use Niftech, better than trying to eye it and setup stations for 12th scale aren't common). Other tools are common hex drivers, 3/16th socket type driver, pliers, etc. I have 4 mini digital scales for weight balancing / tweak setting and you can get those cheap off Ebay.

Tires will depend on class that you run, track surface, etc, easiest to make friends with your club members and ask what they run. Common to see something like Yellow rear / Lilac front Jacos and variations around that. Again, best to check with a local.

Hmm, did that cover most of it? The car you get will have setup suggestions which will get you started, so no point into going into that.

Biggest suggestion is to be as precise as you can on your setup, small things are big things in 12th scale.
__________________
BMI CH12 - Novak, Futaba, KO, TP, Protek
Speedmerchant Rev 4.5 - Retired
CRC 3.2R - Retired
wile2k is offline   Reply With Quote
Old 09-10-2010, 05:04 PM   #34460
Tech Addict
 
js058515's Avatar
 
Join Date: Oct 2008
Location: SoCal
Posts: 574
Trader Rating: 6 (100%+)
Default

Excellent info wile2k! I would almost say you don't need to sift through this whole thread after that post, but you should still sift through this whole thread. At least go back to 2009 posts.
js058515 is offline   Reply With Quote
Old 09-10-2010, 07:48 PM   #34461
Tech Master
 
WildManDriving's Avatar
 
Join Date: Sep 2008
Location: Radelaide
Posts: 1,410
Trader Rating: 29 (100%+)
Default

Readily available to me is Jaco and Xceed tyres, what colour etc would be best to start with on an abrasive med to high grip tarmac surface (been surfaced with netball court paint) The surface has only recently been done and I don't know of anyone having tested it with 1/12.
__________________
. . . - - - Now enjoying Proline tyres - - - . . .
Scale race models: RCHobbyzone, Mugen, Reds, Xpert, Contact, Neo+.
Toy cars: Xray T4'15, Hudy, Nosram/Muchmore, Protoform.
No longer defined as a Off or On-road racer, but simply a RC enthusiast.
WildManDriving is offline   Reply With Quote
Old 09-10-2010, 07:58 PM   #34462
Tech Elite
 
Yokomo_Ant3's Avatar
 
Join Date: Apr 2008
Location: Australia
Posts: 2,405
Trader Rating: 29 (100%+)
Default

Quote:
Originally Posted by WildManDriving View Post
Readily available to me is Jaco and Xceed tyres, what colour etc would be best to start with on an abrasive med to high grip tarmac surface (been surfaced with netball court paint) The surface has only recently been done and I don't know of anyone having tested it with 1/12.
Im not sure what track you race at in Melbourne, but i took my 1/12 to TFTR last year and it worked great there. From the above tyres, i would stay away from jaco on asphalt. The fronts are ok, but the rears dont work. I would get Xceed Med rears, hard fronts Jaco purple fronts work too.

Antoni
__________________
Antoni Caretti

Team Yokomo - Racing Performer - Sweep Racing
Yokomo_Ant3 is offline   Reply With Quote
Old 09-10-2010, 08:27 PM   #34463
Tech Master
 
WildManDriving's Avatar
 
Join Date: Sep 2008
Location: Radelaide
Posts: 1,410
Trader Rating: 29 (100%+)
Default

Quote:
Originally Posted by Yokomo_Ant3 View Post
Im not sure what track you race at in Melbourne, but i took my 1/12 to TFTR last year and it worked great there. From the above tyres, i would stay away from jaco on asphalt. The fronts are ok, but the rears dont work. I would get Xceed Med rears, hard fronts Jaco purple fronts work too.

Antoni
I'm thinking ahead for Bendigo if I can get a handle of 12th scale quick enough. What tyres do you use outside of these brands? I will get those recommendations as practice will be at TFTR.
__________________
. . . - - - Now enjoying Proline tyres - - - . . .
Scale race models: RCHobbyzone, Mugen, Reds, Xpert, Contact, Neo+.
Toy cars: Xray T4'15, Hudy, Nosram/Muchmore, Protoform.
No longer defined as a Off or On-road racer, but simply a RC enthusiast.
WildManDriving is offline   Reply With Quote
Old 09-10-2010, 10:39 PM   #34464
Tech Elite
 
spring71's Avatar
 
Join Date: Oct 2008
Location: Chino, CA
Posts: 3,865
Trader Rating: 3 (100%+)
Smile

Joel Johnson is running Ron Rossetti's 1/12 scale Mod at TQ RC RACING

He got 9.6sec, it's the fastest lap time at TQ.

Check out the video.

+ YouTube Video
ERROR: If you can see this, then YouTube is down or you don't have Flash installed.


See you this Sunday, TQ Carpet Championship Series FINAL !!

www.tqrcracing.com
__________________
TQ RC RACING
Indoor RC Race Track & Hobby Shop in Chino, CA
Online Shop
http://www.tqrcracing.com
[email protected]
spring71 is offline   Reply With Quote
Old 09-10-2010, 10:54 PM   #34465
Tech Master
 
tl2111's Avatar
 
Join Date: Mar 2002
Location: Love 1/8th
Posts: 1,561
Trader Rating: 21 (100%+)
Send a message via MSN to tl2111
Default

Quote:
Originally Posted by WildManDriving View Post
I'm thinking ahead for Bendigo if I can get a handle of 12th scale quick enough. What tyres do you use outside of these brands? I will get those recommendations as practice will be at TFTR.
beside Xceed, Jaco, In Sydney we use speedmind as well last year National Champion won with speedmind tyres. we mainly use 35f/30r on green track. if steering is needed then 32f/32r. PM me if you want to try it.
__________________
*Tourer**Futaba***SpeedPassion
*F1**4PX***TORO
*12th**4PX***TORO
*8th**4PX***OS Speed XZ-R
*10th**4PX***OS Speed XZ
tl2111 is offline   Reply With Quote
Old 09-11-2010, 12:33 AM   #34466
Tech Adept
 
Join Date: Jun 2006
Location: Florida
Posts: 216
Default

WOW thanks a lot guys for all your help. That tire chart was exactly what I needed, and to wile2k, yes you have definitely answered all my questions. I'll have to study that post for a while to fully absorb it.
I'll be doing a little more research on a bunch of the stuff that you mentioned and will report back with any more questions if I have them. Thanks again.
Luke W is offline   Reply With Quote
Old 09-11-2010, 02:15 AM   #34467
Tech Initiate
 
Join Date: Dec 2006
Location: Wrexham, North Wales
Posts: 37
Default

hmm which to get ctc gen xl or associated r12r5.1 ???????????????
finch is offline   Reply With Quote
Old 09-11-2010, 03:15 AM   #34468
Tech Elite
 
Yokomo_Ant3's Avatar
 
Join Date: Apr 2008
Location: Australia
Posts: 2,405
Trader Rating: 29 (100%+)
Default

Quote:
Originally Posted by WildManDriving View Post
I'm thinking ahead for Bendigo if I can get a handle of 12th scale quick enough. What tyres do you use outside of these brands? I will get those recommendations as practice will be at TFTR.
CRC tyres work very well also These are what ill probably be running at the Nationals. Unsure of compound yet, need to test more
__________________
Antoni Caretti

Team Yokomo - Racing Performer - Sweep Racing
Yokomo_Ant3 is offline   Reply With Quote
Old 09-11-2010, 05:15 AM   #34469
Tech Champion
 
Join Date: Feb 2003
Location: Sydney, Australia
Posts: 5,310
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by Yokomo_Ant3 View Post
CRC tyres work very well also These are what ill probably be running at the Nationals. Unsure of compound yet, need to test more
The CRC tires are perhaps very slightly better than the exceeds, but the rims don't break. At the recent SA state titles CRC tires where on the 4 fastest cars on the track. We have prefered the feel of Magenta rears with purple fronts. I suggest people test around this combo as it has proven to be fast.
__________________
Blade: Andro Treiber H 79g AN
FH: Donic Bluefire M3 Max Blk
BH: Donic Bluefire M2 Max Red
Powered by Falco
Dragonfire is offline   Reply With Quote
Old 09-11-2010, 11:06 PM   #34470
Tech Regular
 
TonyK's Avatar
 
Join Date: Apr 2008
Location: Chicago
Posts: 272
Trader Rating: 5 (100%+)
Default

Thanks for this post. It had answered a couple of questions I was thinking about. This will be the first time I will be running a 12 scale on a track and a little nervous abut the speeds these can run.





Quote:
Originally Posted by wile2k View Post
I'd suggest starting with a car that is similar (or at least common) to what others at your club will be racing with. It will make it easier to get help or flesh out setup problems that you might run into. 12th scale can be finicky, sometimes something really small will make a big difference.

CRC GenXL and Associated 12R5 are pretty common and definitely competative. BMI with the old school front end is pretty straight forward for someone to help you with. Speedmerchant with the old front end is again straight forward. The newer front ends might be harder to help you with until people have them figured out a bit better.

Tekin RS speed control is common and pretty well sorted out (probably go with the RS / Tekin motor combo that is correct for the class that you'd be running, i.e. 17.5 or 13.5). I'm going with the new Novak Kinetic 1S and Ballistic combo but it isn't as well sorted out yet since the Kinetics are pretty new. The AE Black Diamond is interesting. It is really spendy and isn't computer programmable (has to be sent to the factory for firmware upgrades), but it's finite settings (have a handful of "profiles" for the various functions) might be, in a way, easier to setup and it is unquestionably fast. I'm not necessarily suggesting it, but it might be worth putting in your research queue.

Servo, Futaba 9650 or JR 3650 are the tops of my lists.

Thunderpower packs are well thought of 5000+MAh 50c (although I went with a budget pack from Protek 5000MAH 40c for less $ as I don't think I'll notice or need the 50c rate running 17.5). SMC and others make great packs too, probably won't go wrong if you just do a little research before buying. These are 1S LiPo hard case, but you probably already get that.

Depending on class, you'll want pinion / spurs capable of 60-100mm rollout. Plan to get a bunch of pinions, probably from about 40-60 tooth and a couple spurs 76,80,84 (car will probably come with 88). If you can do some research on your motor / class (ESC rules, sportsman or open) / track size, you can probably slim those down to maybe 2 spurs and a dozen pinions.

Hit up gearchart.com to make rollout charts. Tires will probably be cut and then worn down from about 46mm to 42mm. Consider a tire truer although your club or other members will likely let you use their's and they aren't cheap.

Receiver will be preferably something small but in the end depends on your radio.

Some people are using a voltage booster and some a receiver pack since 1S Lipo is 3.7v and that isn't really enough for stable receiver / servo operation. Take your pick there, I'm going with a small 220MAh 2S LiPo receiver pack from Protek.

Depending on car, front and center springs, tube lube (I'm using Shur Lube), shock oils (Losi or AE but stick to one brand) for tuning. Tire sauce (check what your track uses / allows). Diff lube, bearing oils, etc there (you probably have some of this, just thinking out loud). Camber gauge (RPM works fine and is cheap / simple), ride height gauge (I prefer non-stepped), front end alignment tools (I use Niftech, better than trying to eye it and setup stations for 12th scale aren't common). Other tools are common hex drivers, 3/16th socket type driver, pliers, etc. I have 4 mini digital scales for weight balancing / tweak setting and you can get those cheap off Ebay.

Tires will depend on class that you run, track surface, etc, easiest to make friends with your club members and ask what they run. Common to see something like Yellow rear / Lilac front Jacos and variations around that. Again, best to check with a local.

Hmm, did that cover most of it? The car you get will have setup suggestions which will get you started, so no point into going into that.

Biggest suggestion is to be as precise as you can on your setup, small things are big things in 12th scale.
__________________
A large part of their history is made up of blood and battle. This is not something to shrink away from as a fancier of the breed. Their history should be embraced, understood, and once we have a full understanding, we can control the future.
TonyK is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 04:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 01:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 07:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 08:26 PM



Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 10:11 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net