R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 06-14-2007, 08:38 PM   #25726
Tech Addict
 
IslandBwoy's Avatar
 
Join Date: Nov 2004
Location: Orlando, FL
Posts: 602
Default

Quote:
Originally Posted by Big B View Post
Did you try their website?
it was the first thing i tried. They use to print the chard on their boxes but i just but a set and nothing! Hoping someone here can help me. Need to know where white, purple, pink, dbl pink, yellow fall on the chart.
IslandBwoy is offline   Reply With Quote
Old 06-14-2007, 08:42 PM   #25727
Tech Addict
 
IslandBwoy's Avatar
 
Join Date: Nov 2004
Location: Orlando, FL
Posts: 602
Default

And where can i find a roll out chart (88) spur? I've forgotten all these things in my absense from the sport.
IslandBwoy is offline   Reply With Quote
Old 06-14-2007, 08:45 PM   #25728
Tech Master
 
Big B's Avatar
 
Join Date: Dec 2006
Location: Kent, WA
Posts: 1,154
Trader Rating: 4 (100%+)
Default

www.gearchart.com
Big B is offline   Reply With Quote
Old 06-14-2007, 08:53 PM   #25729
Tech Addict
 
IslandBwoy's Avatar
 
Join Date: Nov 2004
Location: Orlando, FL
Posts: 602
Default

Thanks,

Anyone race at minnreg? Where should I start with a co27
IslandBwoy is offline   Reply With Quote
Old 06-14-2007, 09:03 PM   #25730
Tech Lord
 
protc3's Avatar
 
Join Date: Jun 2003
Location: Spring Hill,Florida
Posts: 10,813
Trader Rating: 13 (100%+)
Default

best bet would be to start with 2x pink front and yellow rear.gear at a 88/30 with 1.75 tire in the rear.adrian told me we were running 19 turn at minnreg.i guess we will play it by ear though
__________________
Jason Breiner
BMI Racing
Team Associated
J Concepts
protc3 is offline   Reply With Quote
Old 06-14-2007, 09:12 PM   #25731
Tech Addict
 
IslandBwoy's Avatar
 
Join Date: Nov 2004
Location: Orlando, FL
Posts: 602
Default

I heard stock but i hope we can do 19.
IslandBwoy is offline   Reply With Quote
Old 06-14-2007, 09:24 PM   #25732
Tech Adept
 
Join Date: Mar 2007
Posts: 225
Default cefx 12 scale

Hey guys,

Does anyone have a set up that works well on asphalt for a CEFX car? I am having problems around the 6 minute mark with rear end traction.

-front
-10 active caster
-shimed on either side
-servo flat
-.20 springs slight pre load
-purple front

-rear
-10,000 weight dampner lube
-thick t-bar
-272 max axle length
-pink rear

Any help would be appreciated
march to my own is offline   Reply With Quote
Old 06-14-2007, 09:57 PM   #25733
Tech Fanatic
 
ChestyV32's Avatar
 
Join Date: Jul 2006
Posts: 897
Trader Rating: 32 (100%+)
Default

try going to a thin t-plate and putting a .010 shim under the front of it and also what are you doping your tires with and how long you letting it sit
__________________
SXT Tire Additive
www.SuperiorHobbies.com
ChestyV32 is offline   Reply With Quote
Old 06-14-2007, 10:01 PM   #25734
Tech Lord
 
protc3's Avatar
 
Join Date: Jun 2003
Location: Spring Hill,Florida
Posts: 10,813
Trader Rating: 13 (100%+)
Default

Quote:
Originally Posted by march to my own View Post
Hey guys,

Does anyone have a set up that works well on asphalt for a CEFX car? I am having problems around the 6 minute mark with rear end traction.

-front
-10 active caster
-shimed on either side
-servo flat
-.20 springs slight pre load
-purple front

-rear
-10,000 weight dampner lube
-thick t-bar
-272 max axle length
-pink rear

Any help would be appreciated
go to the angled servo mounts,lose the purple fronts and try the 2x pink fronts(purples build up traction as they warm up),try also a little lighter on the rear dampening.maybe 5000 and go to the .062 T bar.
__________________
Jason Breiner
BMI Racing
Team Associated
J Concepts
protc3 is offline   Reply With Quote
Old 06-14-2007, 10:03 PM   #25735
Tech Fanatic
 
ChestyV32's Avatar
 
Join Date: Jul 2006
Posts: 897
Trader Rating: 32 (100%+)
Default

hey J you ready or what please remember to bring some thick plates for me and I have your money thanks
__________________
SXT Tire Additive
www.SuperiorHobbies.com
ChestyV32 is offline   Reply With Quote
Old 06-14-2007, 10:23 PM   #25736
Tech Master
 
CarlosG.'s Avatar
 
Join Date: Jul 2004
Location: Falls City,TX
Posts: 1,145
Trader Rating: 12 (100%+)
Send a message via Yahoo to CarlosG.
Default

I am having the same problem down here at the 6 min. mark as well. I have made the rear as soft as i can but it still gets loose.
CarlosG. is offline   Reply With Quote
Old 06-14-2007, 10:30 PM   #25737
Tech Addict
 
IslandBwoy's Avatar
 
Join Date: Nov 2004
Location: Orlando, FL
Posts: 602
Default

Chesty,

What ride height are you running?
IslandBwoy is offline   Reply With Quote
Old 06-14-2007, 10:52 PM   #25738
Tech Fanatic
 
ChestyV32's Avatar
 
Join Date: Jul 2006
Posts: 897
Trader Rating: 32 (100%+)
Default

between 4 and 4.5
__________________
SXT Tire Additive
www.SuperiorHobbies.com
ChestyV32 is offline   Reply With Quote
Old 06-15-2007, 01:58 AM   #25739
Tech Master
 
David Galdo's Avatar
 
Join Date: Aug 2001
Location: Euless, TX
Posts: 1,652
Trader Rating: 15 (100%+)
Send a message via ICQ to David Galdo Send a message via AIM to David Galdo Send a message via MSN to David Galdo Send a message via Yahoo to David Galdo
Default

Carlos:: As closely seated as you are to P2.... what is he doing differently to keep his car planted?

To the others... what alternative is there to the AE shock as it seems I either rebuild it again or find something better...
__________________
Hot Bodies | HPI Racing | HPI TV | Speedzone USA | Team Epic | Trinity | TRC
V-Dezign 4.0
David Galdo is offline   Reply With Quote
Old 06-15-2007, 03:50 AM   #25740
Tech Champion
 
Join Date: Nov 2001
Location: Hawaii, USA
Posts: 7,157
Default

I find with both my CRC and my Darkside that 4 to 4.5 is too low for asphault. When I run it that low my cars are very loose but at 5mm it handles very nicely.

As for alternative shocks...the AE probably builds the easiest but the CRC and IRS shocks are better. They are modified versions of the AE that seem to retain their oil better and are much smoother.
InspGadgt is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 11:03 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0