R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 06-20-2006, 05:22 PM   #18886
Tech Master
 
polesitter61's Avatar
 
Join Date: Feb 2005
Location: Central Florida
Posts: 1,009
Trader Rating: 4 (100%+)
Default

I'm pretty sure even if you did that it would still take the same time to charge as if you did them one at a time? Right? And if one peaked before the other it would kick off the charger and leave the other pack not fully charged? I could be wrong...........it's happened once or twice
__________________
Slickzero R/C products, check them out, very cheap shipping!!!
www.slickzero.com
polesitter61 is offline   Reply With Quote
Old 06-21-2006, 06:52 AM   #18887
Tech Regular
 
FF25510's Avatar
 
Join Date: Aug 2005
Location: Hong Kong
Posts: 489
Default ESC for 4 cell

Hi guys,

i'm new here and i had some questions may be asked before.

From the user guide, there were 5 engine Maps, which Map should i use with a LRP QUANTUM COMPETITION esc for 8 turn motor/4 cell and what's the gear ratio ?

tks guys
FF25510 is offline   Reply With Quote
Old 06-21-2006, 07:25 AM   #18888
Tech Regular
 
Capelracer's Avatar
 
Join Date: Oct 2005
Location: Bunbury, West Oz
Posts: 296
Trader Rating: 2 (100%+)
Default

OK, I've bit the bullet & bought a T-Fource. Any recommendations for rollout for asphalt for a stock motor??? (open, flowing track).

[IMG]CRC T-Fource small[/IMG]
Attached Thumbnails
1/12 forum-crc-t-fource-small.jpg  
Capelracer is offline   Reply With Quote
Old 06-21-2006, 07:54 AM   #18889
Tech Rookie
 
Join Date: Nov 2003
Location: SWEDEN
Posts: 13
Default

Sweat racer Capelracer... got any problems with the battery strap downs?. I got huge problems using them. The body wants to hit them. I use tape and that works outdoors to.

The rollout I dont realy know.. mabye 38-45mm. I have 52 on my Corally for outdoor racing and thats mod.

/Fredde
Heimdal is offline   Reply With Quote
Old 06-21-2006, 08:22 AM   #18890
Tech Champion
 
rayhuang's Avatar
 
Join Date: Dec 2001
Location: Cleveland Heights, Ohio
Posts: 6,511
Trader Rating: 5 (100%+)
Send a message via AIM to rayhuang
Default

Quote:
Originally Posted by FF25510
Hi guys,

i'm new here and i had some questions may be asked before.

From the user guide, there were 5 engine Maps, which Map should i use with a LRP QUANTUM COMPETITION esc for 8 turn motor/4 cell and what's the gear ratio ?

tks guys

depending no traction of course, I would start on 1 and move up till the acceleration out of slow corners starts to make accelerating erratic. Cannot really help on gear ratio.
rayhuang is offline   Reply With Quote
Old 06-21-2006, 11:10 AM   #18891
Tech Regular
 
FF25510's Avatar
 
Join Date: Aug 2005
Location: Hong Kong
Posts: 489
Default

Quote:
Originally Posted by rayhuang
depending no traction of course, I would start on 1 and move up till the acceleration out of slow corners starts to make accelerating erratic. Cannot really help on gear ratio.

Tks
FF25510 is offline   Reply With Quote
Old 06-21-2006, 11:52 AM   #18892
Tech Elite
 
odpurple's Avatar
 
Join Date: Dec 2002
Location: San Francisco
Posts: 2,187
Default

Quote:
Originally Posted by Capelracer
OK, I've bit the bullet & bought a T-Fource. Any recommendations for rollout for asphalt for a stock motor??? (open, flowing track).

[IMG]CRC T-Fource small[/IMG]
It depends on what stock motor you are using. Probably the most popular stock motor at this time for 1/12th is the Trinity Monster Stock. For that motor try rollout in the range of 48-50. At the recent ROAR paved Nats, where the Monster was the handout, we ran 49mm on a medium sized technical track.
If you are running something else post what it is and someone may have a recommendation.
__________________
TOP Racing USA--OD Racing--Novak--Power Push--J Spec
odpurple is offline   Reply With Quote
Old 06-21-2006, 12:23 PM   #18893
Tech Champion
 
Join Date: Jan 2004
Location: Rockville, MD
Posts: 5,058
Trader Rating: 4 (100%+)
Default

What brush and spring combo are you using with that rollout? I normally rollout at 38 to 40 with 767 and green/ blue springs.
__________________
Steve Walter
Sweep Racing USA/ Speed Passion USA/ Karens Famous Cookies (Transporter)
SRW141 is offline   Reply With Quote
Old 06-21-2006, 05:51 PM   #18894
Tech Elite
 
nf_ekt's Avatar
 
Join Date: Aug 2005
Location: 22 Acacia Avenue
Posts: 4,631
Trader Rating: 113 (100%+)
Default

A quick one: just got some CP money 19t's and need advice on spring/brush combo and what to gear it at. Outdoors on medium traction asphalt if that helps.

Also, what front springs are good all-around for the 12l4 on asphalt? Thanks for any input. .
__________________
Up the Irons \m/

Powered by Hotwings, Rolling Rock, and the urge to race toy cars...
nf_ekt is offline   Reply With Quote
Old 06-21-2006, 05:59 PM   #18895
Super Moderator
 
Marcos.J's Avatar
R/C Tech Elite Subscriber
 
Join Date: Sep 2003
Location: Semper Fi
Posts: 25,177
Trader Rating: 140 (100%+)
Default

Quote:
Originally Posted by nf_ekt
A quick one: just got some CP money 19t's and need advice on spring/brush combo and what to gear it at. Outdoors on medium traction asphalt if that helps.

Also, what front springs are good all-around for the 12l4 on asphalt? Thanks for any input. .
Jason can help you there , he is the brain behind the 1/12th scale
Marcos.J is offline   Reply With Quote
Old 06-21-2006, 05:59 PM   #18896
Tech Lord
 
protc3's Avatar
 
Join Date: Jun 2003
Location: Spring Hill,Florida
Posts: 10,813
Trader Rating: 13 (100%+)
Default

i run .020 front springs at all the tracks.they work great and dont collapse as easy.
__________________
Jason Breiner
BMI Racing
Team Associated
J Concepts
protc3 is offline   Reply With Quote
Old 06-21-2006, 05:59 PM   #18897
Super Moderator
 
Marcos.J's Avatar
R/C Tech Elite Subscriber
 
Join Date: Sep 2003
Location: Semper Fi
Posts: 25,177
Trader Rating: 140 (100%+)
Default

Quote:
Originally Posted by protc3
i run .020 front springs at all the tracks.they work great and dont collapse as easy.
man he is fast
Marcos.J is offline   Reply With Quote
Old 06-21-2006, 06:00 PM   #18898
Tech Lord
 
protc3's Avatar
 
Join Date: Jun 2003
Location: Spring Hill,Florida
Posts: 10,813
Trader Rating: 13 (100%+)
Default

i never ran the checkpoint yet.my kamodo has been such a rocket that i never really tried anything after it.
__________________
Jason Breiner
BMI Racing
Team Associated
J Concepts
protc3 is offline   Reply With Quote
Old 06-21-2006, 06:01 PM   #18899
Tech Lord
 
protc3's Avatar
 
Join Date: Jun 2003
Location: Spring Hill,Florida
Posts: 10,813
Trader Rating: 13 (100%+)
Default

thanks bro
__________________
Jason Breiner
BMI Racing
Team Associated
J Concepts
protc3 is offline   Reply With Quote
Old 06-21-2006, 06:02 PM   #18900
Super Moderator
 
Marcos.J's Avatar
R/C Tech Elite Subscriber
 
Join Date: Sep 2003
Location: Semper Fi
Posts: 25,177
Trader Rating: 140 (100%+)
Default

Quote:
Originally Posted by protc3
i never ran the checkpoint yet.my kamodo has been such a rocket that i never really tried anything after it.
why should you
Marcos.J is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 03:21 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0