R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

    Hide Wikipost
Old 10-28-2016, 12:43 PM   -   Wikipost
R/C Tech Forums Thread Wiki: 1/12 forum
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: fenton06
This is a place to share knowledge related to 1/12th scale racing. It is not to be used for conversations.

KITS:
Click links to go to manufacturer product page. If any are missing please add them!

TIRES:
Pre-mounted tires readily available in the US:
Pre-mounted tires readily available in the Europe:
  • Hot Race ??

Gluing your own donuts:
https://www.youtube.com/watch?v=hm7z1rz-74s - Special thanks to Edward Pickering!
Truing tires:
https://www.youtube.com/watch?v=8wqHOLWq6Uc - Special thanks to Edward Pickering!

The following information came from HERE, with some editing and information added. Thanks Christian!

THIS MAY NEED UPDATING FOR THE NEW BLACK CRC CARPET

Brands:
BSR, CRC, Jaco:
Pro One is no longer selling to the public, but it and the brands above are all mounted by BSR and use the same foam. The nomenclature of the BSR vs Jaco/CRC is a little different in a few instances but is otherwise the same. The BSR foam consists of three families, and can be identifed as synthetics, naturals, and blends.

Synthetics - The old school, light weight, easy to true "dry feeling" tires. These include tires like CRC/Jaco Yellow (BSR White), Black, Gray, etc. These tires offer the highest wear rate and lowest grip. Many racers continue to use these nder high bite conditions.

Naturals - These tires are usually the best alternative for low bite and asphalt. They include Pink, Magenta, Double Pink, Lilac (BSR Team Purple), Purple, and other tires. These tires provide a ton of grip, but tend to get sticky in high bite conditions. This rubber does not wear as easily, and the cars will pick up gunk and fibers from the carpet under most high bite conditions. This is especially bad if the humidity is high.

Blends - These are the tires most people run today. They were initially called "JFT foam" by some, as it was believed that the tires were the same as the JFT tires. We can divide the blends further into two groups: high rubber and low rubber content. The high rubber would be the new rear Orange and Red from the BSR family, and the low rubber would be the Green and Blue varieties. When, asked about the difference, John Foister from BSR Tires said they came from the same "family" of foam, but they offered different grip. According to John, the Green/Blue has more bite than Orange/Red, but from track testing Oranges offer more bite than Green (being equivalent to in hardness) when the grip is high and absolutely no grip when it is lower. The Orange foam has a denser pore structure and the tire is not as prone to chunking. It is also important to note is that BSR Blue rears are not the same as the BSR Blue fronts!

JFT:
JFT stands for Japan Foam Tire. They started the new wave of foam tires we are all using now (Blue/Blu, Green/Greene, Dbl Blue, etc). These tires are a little different than the BSR tire family, but work in very similar conditions. They offers four varieties A (asphalt), C (carpet), S (???), and R (???). This does not mean that those types only work on that surface, but this is what they recommend.

JFT uses the same foam for fronts and rears if the color is the same.

A: Used on asphalt, considered close to the natural rubber variety and are named consistently with other natural tires.
C: Used on carpet, considered a blend.
S: Used on carpet?, tires are ???
R: Used on carpet?, tires are ???

For setup, the JFT foam seem to generate more bite than the BSR, therefore the car tends to be a little more aggressive.

Ulti:
Ulti is another Japanese brand that offers an array of compounds. They have their own way of rating tires, and are difficult to equate to other brands. They have 4 different varieties, each in varying degrees of hardness.

J: High rubber content tire, similar to Pink/ Magenta. Soft would be close to a pink. These offer the most bite and are great for asphalt/carpet front tire. (J hard being very popular)
X: "Balanced" blend, similar to JFT Blue/ Green. Soft is equivalent to Green, medium to Blue in hardness. Great for carpet!
Y: High synthetic blend with lower grip, and is not a very popular variety.
Z: A very expensive "special" foam that is supposed to be magic on asphalt. Only make it in soft shore.
European tires:
There are many great European foam tire brands that use their own types of foam, as well as traditional foams. SOmeone with more knowledge about them will need to fill this in!

Tire Diameter:
If you are racing on carpet, you have to evaluate how much grip your track has. If your track is low to medium grip, you can run bigger tires. If you are on higher bite you have to cut them smaller, there is simply no way around it. Bigger tires are needed for asphalt, especially in the rear. The larger tires provide much needed lateral bite.

Carpet (mm):
Low - Medium Bite
Front: 42.0 - 42.5
Rear: 42.5 - 43.00
Medium - High Bite
Front: 40.5 - 41.0
Rear: 41.5 - 42.0
Big Race
Front: 39.5 - 40.0
Rear: 40.5 - 41.0
Asphalt (mm):
Parking Lot
Front: 43.0 - 44.0
Rear: 44.0 - 45.0
Prepped High Bite
Front: 42.0 - 43.0
Rear: 43.0 - 44.0

Tire Saucing:
Most facilities have moved towards odorless traction additives such as SXT. Some of additives evaporate very quickly and some do not. This seems to be something that is also dependent on tire compound and ambient temperature. For example, saucing a Green compound seems like it never dries, especially when tjhe temperature is lower. We have found that wiping the tires off 15 minutes before we go run allows the sauce to cure, which makes the car come in much quicker with Green rears. Blue compounds on the other hand, do fine when wiped off right before hitting the track.

Saucing half front and full rear is a good initial starting point. If the front of the car is too agressive you can sauce les than half, or for a shorter amount of time.
Tire Fuzzing:
In conditions of increasing grip, foam tires will somewtimes get sticky and pick up fuzz and debris from the track. This is highly dependent on the rubber sedan tire that is being run at your local track and the compound/ type of foam you are running on you car. The softer the sedan tire and the harder/higher rubber content in your foam tire, trouble with fuzzing seems more likely to occur.

There are ways to get around fuzzing under most conditions, and usually involves the selection of the correct foam compound. The more fuzz you get, the softer/lower rubber content you want to run.

Examples:
Problem: Car fuzzes with Lilac/Team Purple fronts and car starts pushing.
Solution: Use a softer front tire and or different family of foam. Replace it with Blue or Double Blue front.

Problem: Car loses rear bite 6 minutes into the run. Blue rear tires look almost clean but have small carpet hairs.
Solution: Use Green rear tires. The softer compound wears instead of getting sticky, minimizing fuzz.

Tire Selection:
Starting out, pick 2 tire compounds for the front and rear. The following should have you covered 99% of the time.

Front - Green and Blue (BSR) or Green and Light Blue (JFT)
Rear - Blue and Double Blue (BSR) or Blue and Dark Blue (JFT)

You may wonder about other compounds out there and if they might be better, trust me, they probably won't be. Even if there are other tires that can be as fast, the synthetic family wears out really fast and the high natural rubber will probably fuzz on you over an 8 minute run. The blends family seems to be the most versatile foam type available today. They last awhile, and sticking to them will make your process of tire selection simpler.
Tire Charts:
BSR/CRC/Jaco



Contact



Corally



JFT (Japan Foam Tire)



Ulti



Enneti (Xceed)



ELECTRONICS:
ESC:
As of now, ROAR is staying 1S (3.7V nominal; 4.2V fully charged) for 1/12. There are many 1S ESC's with a built in BEC so nothing else is required to power the receiver and servo.

If you don't want to lock yourself into a 1S specific ESC, you do have other options! It is possible to use your 2S ESC without a booster or receiver pack, and the ESC simply supplies the lower voltage. If that does not appeal to you, you will need to use an Rx pack or booster. The Rx pack and booster will both supply the receiver with a higher voltage than the 1S pack.

If you decide to use an Rx pack, MAKE SURE TO REMOVE THE RED WIRE FROM THE ESC PLUG THAT GOES INTO THE RECEIVER!!!

If you choose to use a voltage booster, it works exactly how it sounds. Instead of plugging the ESC into the receiver, it plugs into the booster, and the booster plug goes to the ESC, supplying the higher voltage.

1S ESC:
If there are any missing please add them!!

If anyone would like a need for a chart comparing the ESC's specs PM fenton06 and I'll get one made and put in here!
Voltage Boosters:
If there are any missing please add them!
Servos:
BODIES:
Black Art (CRC - US Dist):
  • Audi R8C - BA002 - .020 Thick



  • Black Market (Mohawk 12) - BA005 - .020



  • Lola B10 - BA006 - .020 thick
  • Toyota TS030 - BA008 - .020 thick

    Lola - black/red, TS030 - green/pink


PROTOForm:

Reflex Racing/RSD:

SUSPENSION ADJUSTMENTS:

Print Wikipost

Reply
 
Thread Tools Search this Thread
Old 03-05-2006, 04:23 AM   #17566
Tech Addict
 
Hoggy's Avatar
 
Join Date: Jun 2005
Location: Melbourne
Posts: 611
Trader Rating: 26 (100%+)
Default

Hey guys
Anyone here put a brushless system in their 1/12th?
i Was thinking of getting a GTB 5.5 but i have have a hacker 6 turn brushless system lined up but im not sure if it works with 4 cells, does anyone know if it does or run the hacker system?
Cheers
Hoggy is offline   Reply With Quote
Old 03-05-2006, 08:32 AM   #17567
Tech Champion
 
Scottrik's Avatar
 
Join Date: Sep 2004
Location: Billings, MT
Posts: 6,122
Trader Rating: 238 (100%+)
Default

Do a search of this thread for "GTB" and you'll see pics of my carpet knife with GTB/Velocity system installed. It is a bit of work to get everything oriented correctly, but it works.

Scottrik.
Scottrik is offline   Reply With Quote
Old 03-05-2006, 09:10 AM   #17568
Tech Adept
 
Team Girth's Avatar
 
Join Date: May 2005
Location: Long Beach
Posts: 103
Default AH-12

i have this car and i built it and never ran it..

the car will be everything but the pod bulkheads and diff... (i was using IRS stuff and still am on a different car) PM offers... looking to get about $100 for it..
Team Girth is offline   Reply With Quote
Old 03-05-2006, 04:14 PM   #17569
Tech Regular
 
Join Date: May 2005
Posts: 338
Default

Quote:
Originally Posted by Ike
You guys that run the QC2, what settings are you finding the best for stock racing? I haven't touched it since I've been using my GT7 more and it seemed pretty good as is, but am now going to be using it more often.

QC2 - set hipoint on trans to 150 and brake to 100 - then set up speedo - then set speedo to mode 4 with linear brake and 0 drag brake

on a Novak (GTX)mode 5 works for me also - still have to set up trans the same way
DLM2005 is offline   Reply With Quote
Old 03-05-2006, 04:43 PM   #17570
Ike
Tech Master
 
Ike's Avatar
 
Join Date: Jan 2004
Posts: 1,131
Trader Rating: 4 (100%+)
Default

Quote:
Originally Posted by DLM2005
QC2 - set hipoint on trans to 150 and brake to 100 - then set up speedo - then set speedo to mode 4 with linear brake and 0 drag brake

on a Novak (GTX)mode 5 works for me also - still have to set up trans the same way
Thanks man, that's almost exactly what I did lastnight. Though I set EPA to 125 which was the max.
Ike is offline   Reply With Quote
Old 03-05-2006, 09:33 PM   #17571
Tech Champion
 
JayBee's Avatar
 
Join Date: Mar 2004
Location: 12TH-MAN COUNTRY
Posts: 6,803
Trader Rating: 31 (100%+)
Default

For the 8/32" locknut on the rear axle, is there an metal threaded alternative?
__________________
R C 3 G R A F I X _ F U S I O N . G R A P H I X _ S E A T T L E - R/C - R A C E R S _ E M E R A L D C I T Y R C . C O M

A E - 12R5.2 _ S M - REV8 PRO
JayBee is offline   Reply With Quote
Old 03-05-2006, 10:43 PM   #17572
Tech Apprentice
 
Join Date: Jul 2004
Posts: 84
Trader Rating: 39 (100%+)
Default

The wheel nut for a TC3/TC4 is a standard 8-32 locknut.
Rick S is online now   Reply With Quote
Old 03-05-2006, 10:58 PM   #17573
Tech Elite
 
Anthony.L's Avatar
 
Join Date: Oct 2005
Location: Federal Way, WA
Posts: 2,701
Trader Rating: 36 (100%+)
Default

Quote:
Originally Posted by JayBee
For the 8/32" locknut on the rear axle, is there an metal threaded alternative?
I don't think you want metal JB, why are you thinking so?
Anthony.L is offline   Reply With Quote
Old 03-05-2006, 11:07 PM   #17574
Tech Champion
 
Still Bill's Avatar
 
Join Date: Jan 2004
Location: Reno, NV
Posts: 7,016
Trader Rating: 11 (100%+)
Default

Quote:
Originally Posted by Anthony.L
I don't think you want metal JB, why are you thinking so?
I use aluminum lock nuts with no issues...Also have Slapmaster thrust bearing assembly under it.
__________________
Constantly evolving CRC WGT and WGT-R/T...Carpet & Asphalt...All thanks to Team CRC.
Still Bill is offline   Reply With Quote
Old 03-05-2006, 11:27 PM   #17575
Tech Champion
 
JayBee's Avatar
 
Join Date: Mar 2004
Location: 12TH-MAN COUNTRY
Posts: 6,803
Trader Rating: 31 (100%+)
Default

Quote:
Originally Posted by JRX-S Bill
I use aluminum lock nuts with no issues...Also have Slapmaster thrust bearing assembly under it.
Thanks... I didn't think there were any issues
__________________
R C 3 G R A F I X _ F U S I O N . G R A P H I X _ S E A T T L E - R/C - R A C E R S _ E M E R A L D C I T Y R C . C O M

A E - 12R5.2 _ S M - REV8 PRO
JayBee is offline   Reply With Quote
Old 03-05-2006, 11:39 PM   #17576
Tech Elite
 
Anthony.L's Avatar
 
Join Date: Oct 2005
Location: Federal Way, WA
Posts: 2,701
Trader Rating: 36 (100%+)
Default

Quote:
Originally Posted by JayBee
Thanks... I didn't think there were any issues
Ok, what's the advantage? The alum nut is going to weigh more.
Anthony.L is offline   Reply With Quote
Old 03-06-2006, 12:12 AM   #17577
Tech Champion
 
JayBee's Avatar
 
Join Date: Mar 2004
Location: 12TH-MAN COUNTRY
Posts: 6,803
Trader Rating: 31 (100%+)
Default

Quote:
Originally Posted by Anthony.L
Ok, what's the advantage? The alum nut is going to weigh more.
I got some coming so when they get here I'll weigh them and let you know. They'll probably be like .008 of a gram more
__________________
R C 3 G R A F I X _ F U S I O N . G R A P H I X _ S E A T T L E - R/C - R A C E R S _ E M E R A L D C I T Y R C . C O M

A E - 12R5.2 _ S M - REV8 PRO
JayBee is offline   Reply With Quote
Old 03-06-2006, 12:21 AM   #17578
Tech Champion
 
Still Bill's Avatar
 
Join Date: Jan 2004
Location: Reno, NV
Posts: 7,016
Trader Rating: 11 (100%+)
Default

Quote:
Originally Posted by Anthony.L
Ok, what's the advantage? The alum nut is going to weigh more.
I use the low profile ones; so, weight is negligible.

Advantage is a flat machined surface making contact with my Slapmaster assembly.
__________________
Constantly evolving CRC WGT and WGT-R/T...Carpet & Asphalt...All thanks to Team CRC.
Still Bill is offline   Reply With Quote
Old 03-06-2006, 07:57 AM   #17579
Tech Initiate
 
CandyMan's Avatar
 
Join Date: Apr 2005
Location: Inola,OK U.S.A.
Posts: 30
Default

Hey guys, pardon my ignorance to 1/12 scale but what tires are good for stock on medium bite ozite? I'm thinking of buying a new carpet knife and was wondering if the ones in the kit good?
CandyMan is offline   Reply With Quote
Old 03-06-2006, 08:54 AM   #17580
Tech Elite
 
Join Date: Oct 2003
Location: Green Bay,WI
Posts: 3,006
Trader Rating: 1 (100%+)
Send a message via AIM to R/C Anonymous
Default

Anyone have a good base setup for a smooth, low-to-medium grip carpet track for a CRC T-Fource?
__________________
Geoff C.
R/C Anonymous is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
New to the forum mig rod Electric Off-Road 1 01-05-2008 05:23 PM
hi i need help and im new to the forum racer4 Rookie Zone 4 01-21-2007 02:37 PM
Why is this forum listed under the On Road Forum? sport10 Onroad Nitro Engine Zone 0 01-11-2007 08:06 AM
Forum Changes... futureal Wisconsin & Illinois Racing 3 10-28-2002 09:26 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 11:37 AM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net

SEO by vBSEO 3.5.0