Castle Creations Mamba Max Pro Sensored ESC
#1246
Tech Apprentice
Hi all
Ran this weekend and everything went well. My driving still sucks! had the mmp on 50% turbo 8000-17000 rpm FDR at 6 and it was just as fast as the other guys,temp at 60C. could do with more braking though.
Ran this weekend and everything went well. My driving still sucks! had the mmp on 50% turbo 8000-17000 rpm FDR at 6 and it was just as fast as the other guys,temp at 60C. could do with more braking though.
#1247
#1248
Tech Adept
Glad you had a good Nats. Where did you end in finals ?
What chassis you running ?
How was the track condition ?
#1249
Could someone explain to me how to know where to set the RPM range in cheat mode. I have an Associated SC10 with a Novak 13.5t motor. Running a 75 spur and a 14 pinion for a FDR of 8.125. I run on small and large tracks. Maybe I need two settings depending on the track.
#1250
Tech Addict
What settings do i use to tone my 13.5 down to 17.5 levels? Or is the smartsence mode slow enuff?
#1251
Well if you are running the new version of the software it allows you to limit your total forward power. However if the 17.5's are running with cheat mode, dynamic timing, then just running the 13.5 in smart sense will be probably too slow. But I would start there, then possible limit your total forward power via the castle link.
#1252
I see Castle put out an update to there software. Who's gonna be the first to try it? I am sticking to 1.26 unitl I see 1.28 is marked as final. No beta tester here. This stuff is too expensive.
#1253
I have had no problems with any of the previous "beta" firmwares. 1.26 is beta as well, you know. The only way you burn something up is user error (too much timing for a given motor/track, etc)
#1254
With 1.29, the starts go back to being smooth with sensorless systems as it was with 1.26.
I have had no problems with any of the previous "beta" firmwares. 1.26 is beta as well, you know. The only way you burn something up is user error (too much timing for a given motor/track, etc)
I have had no problems with any of the previous "beta" firmwares. 1.26 is beta as well, you know. The only way you burn something up is user error (too much timing for a given motor/track, etc)
http://www.castlecreations.com/downloads/frh-mamba.html
#1255
Interesting. If you plug the ESC into the link, you will see 1.26 listed as beta.
Either way, "beta" is not anything to be worried about. I have used many different versions of "beta" firmware throught the years (I run a lot of micro stuff as well), and never once had any issues Castle wouldnt release something unless they are sure it works as intended
Either way, "beta" is not anything to be worried about. I have used many different versions of "beta" firmware throught the years (I run a lot of micro stuff as well), and never once had any issues Castle wouldnt release something unless they are sure it works as intended
#1256
Interesting. If you plug the ESC into the link, you will see 1.26 listed as beta.
Either way, "beta" is not anything to be worried about. I have used many different versions of "beta" firmware throught the years (I run a lot of micro stuff as well), and never once had any issues Castle wouldnt release something unless they are sure it works as intended
Either way, "beta" is not anything to be worried about. I have used many different versions of "beta" firmware throught the years (I run a lot of micro stuff as well), and never once had any issues Castle wouldnt release something unless they are sure it works as intended
#1257
Anyway, if 1.26 is working that's great. I like the new torque control feature of the controller. Especially in off road. It is much better than using a slipper to adjust for traction. Now if they would just add "turbo" for onroad and really big straights.
Last edited by macdude; 08-13-2010 at 12:49 PM. Reason: spelling.....:)
#1258
i had an issue after i installed the new firmware the esc would stall in the middle of the run as if it were thermaling and its the exact same gearing and everything i ran on previous software and the fan was on when this happened then if you wait a second it wouls cool off and then run for a little longer then thermal again. at least i hope it didnt thermal but it did this after i installed the firmware.
#1259
Tech Adept
Hi All
When I Perform motor test mode and after the test it does not display the motor KV but instead it displays "motor test data has been acquired"
Before it use to show the KV. Am I doing something wrong ?
When I Perform motor test mode and after the test it does not display the motor KV but instead it displays "motor test data has been acquired"
Before it use to show the KV. Am I doing something wrong ?
#1260
Tech Addict
iTrader: (1)
The MMP is great for offroad with the Torque limiter, had a good play around with it yesterday with a Hacker 10.5 in a Duratrax Buggy and wound down was still poping the front wheels half way down the straight.
Knocked the TL back to 3
start power to med
punch to 50%
timing 35 deg
rpm range 4000-7500
spur 87 pinion 19
Thanks Steven