Castle Creations Mamba Max Pro Sensored ESC
#1231
Tech Addict
iTrader: (1)
i had an issue after i installed the new firmware the esc would stall in the middle of the run as if it were thermaling and its the exact same gearing and everything i ran on previous software and the fan was on when this happened then if you wait a second it wouls cool off and then run for a little longer then thermal again. at least i hope it didnt thermal but it did this after i installed the firmware.
On the weekend i ran 10.5 and 17.5 at the Gold Coast in Australia , the track is large with medium/good grip and very flowing with 3 hair pins.
I just could not find a fast setup for the MMP it was either to much or not enough (maybe i was geard to high) Stock i found was excelent in the infield but lacked the top end of the Tekins and LRP. And for some reason the lack of bracks with the new firm wear Avid 2 was Great.
Steven
Last edited by Casino Kid; 08-04-2010 at 04:10 PM.
#1232
Tech Adept
Jeff no problems with thermal but MMP does have a problem with a sight miss at low rpm.
On the weekend i ran 10.5 and 13.5 at the Gold Coast in Australia , the track is large with medium/good grip and very flowing with 3 hair pins.
I just could not find a fast setup for the MMP it was either to much or not enough (maybe i was geard to high) Stock i found was excelent in the infield but lacked the top end of the Tekins and LRP. And for some reason the lack of bracks with the new firm wear Avid 2 was Great.
Steven
On the weekend i ran 10.5 and 13.5 at the Gold Coast in Australia , the track is large with medium/good grip and very flowing with 3 hair pins.
I just could not find a fast setup for the MMP it was either to much or not enough (maybe i was geard to high) Stock i found was excelent in the infield but lacked the top end of the Tekins and LRP. And for some reason the lack of bracks with the new firm wear Avid 2 was Great.
Steven
What setup did you run in 13.5 with cheat mode and torque ?
#1233
This Sunday I Run with SP V3 4,5T
but do not know Torque Limit Setting
link of the track
can I help for setting?
thank's!
but do not know Torque Limit Setting
link of the track
+ YouTube Video | |
can I help for setting?
thank's!
#1235
Tech Adept
What is a good RPM range, Torque range, Trottle curve, Brake curve for 13.5
#1236
Tech Apprentice
2Quick are you in SA? And are u racing in Durds this weekend? I cant seem too find decent speed out of my 13.5.Running team Wave and mmpro 50% timing and a FDR of 6. Infield the car is pretty strong. Help!
#1237
Tech Adept
Won't make it for Durb's this Weekend, other commitments. Maybe next Nats.
I ran Cheat mode 5600 - 19000 Rpm with Torque enabled at 10 if running latest firmware. Gave me decent speed and less Torque coming out of the corners. Had pace against the Tekins and Speed passions, just struggled with handling. Hopefully got it sorted. You can perhaps push the Rpm start off higher for Durb,s...maybe 7500 to 8000 rpm's. Try FDR of 5.85
Let me know how it went.
#1238
Tech Fanatic
can somebody help me??..ok! im runnign the mmp with a duo 2 motor @ zero
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
#1239
What wind motor?
can somebody help me??..ok! im runnign the mmp with a duo 2 motor @ zero
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
#1240
can somebody help me??..ok! im runnign the mmp with a duo 2 motor @ zero
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
settings are
50*timing
rpm 5000 to 15100
start power low
5000 50c lipo
tc4
punch off
the track is 100 x50
my motor keeps running hot no matter what i do it as far as gearing..i tryed 7.5fdr & the temps was like 220..i tryed 6.6fdr & the temps stayed the same..& i tryed 6.3 & still the same..the weather was mild in the low 80's..but the hott temps dont seem to bother the motor...so my question is what am i doing wrong..is the motor bad?? or that motor just get hott like that...& im not useing a fan...thanks!
#1241
Tech Fanatic
I am running a duo 2 17.5. With the MMP I would stay in the 6.6-6.25 range. I am currently running 35 degrees with 5 -15 k rpm. I would try lowering your timing. If you are loosing too much top end, then I would adjust your rpm range. Try increasing your starting rpm. If your track is pretty flowing where you are wound out most of the time, then adjusting your RPM range might make a big difference. But the first thing I would try is lowering the timing.
#1242
thanks! sorry im running a duo 2 17.5.......drop my timing & gear up?...imma try this.. this weekend....this past weekend i was on the same pace with the big boys in 17.5 .. top 5 we all did 25laps(even though i was 10sec off the leader)..but that a big improvement for me when i was @ least 1lap down b4...i just dont wanna burn my motor up tryna keep up....thanks!
#1243
Tech Fanatic
#1244
Tech Adept
Hi All
I ran 13.5 this Weekend in touring car. Went well with old Firmware 1.2.6, just struggled with car setup, had a lot of understeer off power and back side loose on power, but straight line speed no problem, kept up with the Tekins and Speed passions etc.
Setup :
Ballistic 13.5 motor
FDR of 6.46
Start Power High
Motor Timing 50
Cheat mode 8000 - 9200 rpm
Trottle Linear
I think I will go higher with end rpm. I need more speed in order to win. Hope the turbo function gets released soon.
I ran 13.5 this Weekend in touring car. Went well with old Firmware 1.2.6, just struggled with car setup, had a lot of understeer off power and back side loose on power, but straight line speed no problem, kept up with the Tekins and Speed passions etc.
Setup :
Ballistic 13.5 motor
FDR of 6.46
Start Power High
Motor Timing 50
Cheat mode 8000 - 9200 rpm
Trottle Linear
I think I will go higher with end rpm. I need more speed in order to win. Hope the turbo function gets released soon.