Xray T1
Tech Master
iTrader: (1)
theres a nice big thread going on about it. check a few threads down.
T1R CARPET FOAM SETUP
Looking for a starting point for a foam tire/carpet stock motor setup for my new xray T1R. I have searched this forum and others for help and most setups I have been able to find are for T1FK. When running other cars (xxxs and tc3)I was able to find setups on the mfg web site but not the case with xray. I race on a large indoor carpet track and good stock lap times are in the low 14sec range with mod drivers able to get down to 12.9sec. I have installed stiffer springs(purple front and violet rear) gone to 2 holes open front and rear in the shocks. I am interested in what has worked for others on carpet???????
Tech Master
iTrader: (1)
T1R CARPET SETUP
Yes I have checked there. Only one T1R setup there for outdoor rubber tires. Cant get the search function to show any other t1r setups. Can evo2 setups that use the c-hub suspenion be used on the t1r as they are basicaly the same car???
Tech Initiate
Chassis:
Brand and type: T1 RAYCER
Track conditions:
Track (if not listed): Rain City Raceway and Hobbies
Air temperature:
Track temperature:
Traction: High
Track surface: Carpet
Race condition:
Results:
Qualifying result:
Qualifying position:
Best laptime:
Final result:
Final position:
Best laptime:
Suspension geometry Front:
Type of suspension: c-hub suspension
Downstops: 1 mm
Camber Left: -2º
Camber Right: -2º
Ride height mm: 5 mm
Upper link location on shock tower: 2
Toe-in: 0°
Steering block type: composite
Anti-dive (0 or 3 degr.): 0º
Ackermann position: 1
Steering block mounting position: 2
Caster: 3°
Caster Block Type: medium
Front Arm Type: short arms
Suspension geometry Rear:
Type of suspension: c-hub suspension
Downstops: 4 mm
Camber Left: -2º
Camber Right: -2º
Ride height mm: 5 mm
Toe-in: 1º
Anti-squat (0 or 3 degr.): 0º
Upper arm position in upright: 1
Roll Center Position:
Rear Arm Type: short arms
Wheelbase settings:
Wheelbase length: 258 mm
Clips used in front of arm: 4 + 2
Length of the adjustable ball in the bulkhead:
Shockabsorbers Front:
Springs: Light Red (35 lb.)
Spring length:
Spring pre-load:
Oil: 60 wt.
Holes: 2 opened
Upper shock position: 3
Lower shock position: 2
Shock body : composite
Shockabsorbers Rear:
Springs: Light Purple (30 lb.)
Spring length:
Spring pre-load:
Oil: 60 wt.
Holes: 1 opened
Upper shock position: 4
Lower shock position: 2
Shock body: composite
Anti-roll bar front:
Thickness: none
Anti-roll bar rear:
Thickness: none
Balancing of Chassis:
Additional weights left front: none
Additional weights left rear: none
Additional weights right front: none
Additional weights right rear: none
Additional weights center: none
Transponder placement: personal on front bumper
Tires Front:
Make: Jaco
Compound: double pink/orange
Insert: NA
Diameter: 60 mm
Width: 28 mm
Traction compound: TQ Purple (inside 1/3 coated)
Tires rear:
Make: Jaco
Compound: double pink
Insert: NA
Traction compound: TQ Blu (whole tire coated)
Transmission:
Pinion: 30
Spur gear: 96
Final drive ratio:
Roll-out (mm):
Front axle:
Type: differential
Diff. setting: tight
Rear axle:
Type: differential
Diff. setting: medium
Aerodynamics:
Body: Protoform Mazda 6
Wing: stock
Electrics:
Battery: SMC
Battery capacity (mAh): GP 3300
Electric motor brand: Team Brood
Armature: Chameleon 2
Winds: 19
Strands: 1
+ Spring: Trinity Purple
- Spring: Trinity Red
Brush face: serrated
Brush compound: Reedy 767 (+)/ Reedy 769 (-)
Speed controller: Novak Cyclone
Limiter (A):
Drive frequency (Hz): Stock
Initial Brake (%):
Drag brake (on/off): off
Remarks:
Chassis performance: Use stiff upper deck.
Brand and type: T1 RAYCER
Track conditions:
Track (if not listed): Rain City Raceway and Hobbies
Air temperature:
Track temperature:
Traction: High
Track surface: Carpet
Race condition:
Results:
Qualifying result:
Qualifying position:
Best laptime:
Final result:
Final position:
Best laptime:
Suspension geometry Front:
Type of suspension: c-hub suspension
Downstops: 1 mm
Camber Left: -2º
Camber Right: -2º
Ride height mm: 5 mm
Upper link location on shock tower: 2
Toe-in: 0°
Steering block type: composite
Anti-dive (0 or 3 degr.): 0º
Ackermann position: 1
Steering block mounting position: 2
Caster: 3°
Caster Block Type: medium
Front Arm Type: short arms
Suspension geometry Rear:
Type of suspension: c-hub suspension
Downstops: 4 mm
Camber Left: -2º
Camber Right: -2º
Ride height mm: 5 mm
Toe-in: 1º
Anti-squat (0 or 3 degr.): 0º
Upper arm position in upright: 1
Roll Center Position:
Rear Arm Type: short arms
Wheelbase settings:
Wheelbase length: 258 mm
Clips used in front of arm: 4 + 2
Length of the adjustable ball in the bulkhead:
Shockabsorbers Front:
Springs: Light Red (35 lb.)
Spring length:
Spring pre-load:
Oil: 60 wt.
Holes: 2 opened
Upper shock position: 3
Lower shock position: 2
Shock body : composite
Shockabsorbers Rear:
Springs: Light Purple (30 lb.)
Spring length:
Spring pre-load:
Oil: 60 wt.
Holes: 1 opened
Upper shock position: 4
Lower shock position: 2
Shock body: composite
Anti-roll bar front:
Thickness: none
Anti-roll bar rear:
Thickness: none
Balancing of Chassis:
Additional weights left front: none
Additional weights left rear: none
Additional weights right front: none
Additional weights right rear: none
Additional weights center: none
Transponder placement: personal on front bumper
Tires Front:
Make: Jaco
Compound: double pink/orange
Insert: NA
Diameter: 60 mm
Width: 28 mm
Traction compound: TQ Purple (inside 1/3 coated)
Tires rear:
Make: Jaco
Compound: double pink
Insert: NA
Traction compound: TQ Blu (whole tire coated)
Transmission:
Pinion: 30
Spur gear: 96
Final drive ratio:
Roll-out (mm):
Front axle:
Type: differential
Diff. setting: tight
Rear axle:
Type: differential
Diff. setting: medium
Aerodynamics:
Body: Protoform Mazda 6
Wing: stock
Electrics:
Battery: SMC
Battery capacity (mAh): GP 3300
Electric motor brand: Team Brood
Armature: Chameleon 2
Winds: 19
Strands: 1
+ Spring: Trinity Purple
- Spring: Trinity Red
Brush face: serrated
Brush compound: Reedy 767 (+)/ Reedy 769 (-)
Speed controller: Novak Cyclone
Limiter (A):
Drive frequency (Hz): Stock
Initial Brake (%):
Drag brake (on/off): off
Remarks:
Chassis performance: Use stiff upper deck.
Tech Initiate
here you go
Chassis:
Brand and type: T1 RAYCER
Track conditions:
Track (if not listed): Purpose built Carpet
Air temperature:
Track temperature:
Traction: medium
Track surface: Carpet
Race condition: Very bumpy
Results:
Qualifying result: 1
Qualifying position: 1
Best laptime: 12.010
Final result: 1
Final position: 1
Best laptime: 11.880
Suspension geometry Front:
Type of suspension: c-hub suspension
Downstops: 2 mm
Camber Left: -1°
Camber Right: -1°
Ride height mm: 5 mm
Upper link location on shock tower: 2
Toe-in: 0°
Steering block type: composite
Anti-dive (0 or 3 degr.): 0°
Ackermann position: 1
Steering block mounting position: 2
Caster: 6°
Caster Block Type: medium
Front Arm Type: medium
Suspension geometry Rear:
Type of suspension: c-hub suspension
Downstops: 3 mm
Camber Left: -1°
Camber Right: -1°
Ride height mm: 5.0 mm
Toe-in: 3°
Anti-squat (0 or 3 degr.): 0° (upper holes)
Upper arm position in upright: 1
Roll Center Position:
Rear Arm Type: medium
Wheelbase settings:
Wheelbase length: 254 mm
Clips used in front of arm: 2
Length of the adjustable ball in the bulkhead:
Shockabsorbers Front:
Springs: blue
Spring length:
Spring pre-load:
Oil: 35 W
Holes: 4 opened
Upper shock position: 2
Lower shock position: 1
Shock body : composite
Shockabsorbers Rear:
Springs: light blue
Spring length:
Spring pre-load:
Oil: 30 W
Holes: 4 opened
Upper shock position: 3
Lower shock position: 2
Shock body: composite
Anti-roll bar front:
Thickness:
Anti-roll bar rear:
Thickness:
Balancing of Chassis:
Additional weights left front:
Additional weights left rear:
Additional weights right front:
Additional weights right rear:
Additional weights center: 20
Transponder placement: Left off speedo, new hole
Tires Front:
Make: Orion
Compound: 27B
Insert: Sorex C medium
Diameter:
Width: 24mm
Traction compound:
Tires rear:
Make: Orion
Compound: 27B
Insert: Sorex C medium
Traction compound: LRP Grip
Transmission:
Pinion: 21
Spur gear: 93
Final drive ratio: 7,84
Roll-out (mm):
Front axle:
Type: one-way
Diff. setting:
Rear axle:
Type: differential
Diff. setting: medium
Aerodynamics:
Body: Protoform Stratus
Wing: std.
Electrics:
Battery: Orion
Battery capacity (mAh): GP3300SP
Electric motor brand: Revolution
Armature: std.
Winds: 12
Strands: 2
+ Spring: std.
- Spring: std.
Brush face: Serrated
Brush compound: Sprint
Speed controller: LRP Quantum
Limiter (A): Touring Car pr.
Drive frequency (Hz): -
Initial Brake (%): -
Drag brake (on/off): off
Remarks:
Chassis performance: Very fast with plenty of steering...
Chassis:
Brand and type: T1 RAYCER
Track conditions:
Track (if not listed): Purpose built Carpet
Air temperature:
Track temperature:
Traction: medium
Track surface: Carpet
Race condition: Very bumpy
Results:
Qualifying result: 1
Qualifying position: 1
Best laptime: 12.010
Final result: 1
Final position: 1
Best laptime: 11.880
Suspension geometry Front:
Type of suspension: c-hub suspension
Downstops: 2 mm
Camber Left: -1°
Camber Right: -1°
Ride height mm: 5 mm
Upper link location on shock tower: 2
Toe-in: 0°
Steering block type: composite
Anti-dive (0 or 3 degr.): 0°
Ackermann position: 1
Steering block mounting position: 2
Caster: 6°
Caster Block Type: medium
Front Arm Type: medium
Suspension geometry Rear:
Type of suspension: c-hub suspension
Downstops: 3 mm
Camber Left: -1°
Camber Right: -1°
Ride height mm: 5.0 mm
Toe-in: 3°
Anti-squat (0 or 3 degr.): 0° (upper holes)
Upper arm position in upright: 1
Roll Center Position:
Rear Arm Type: medium
Wheelbase settings:
Wheelbase length: 254 mm
Clips used in front of arm: 2
Length of the adjustable ball in the bulkhead:
Shockabsorbers Front:
Springs: blue
Spring length:
Spring pre-load:
Oil: 35 W
Holes: 4 opened
Upper shock position: 2
Lower shock position: 1
Shock body : composite
Shockabsorbers Rear:
Springs: light blue
Spring length:
Spring pre-load:
Oil: 30 W
Holes: 4 opened
Upper shock position: 3
Lower shock position: 2
Shock body: composite
Anti-roll bar front:
Thickness:
Anti-roll bar rear:
Thickness:
Balancing of Chassis:
Additional weights left front:
Additional weights left rear:
Additional weights right front:
Additional weights right rear:
Additional weights center: 20
Transponder placement: Left off speedo, new hole
Tires Front:
Make: Orion
Compound: 27B
Insert: Sorex C medium
Diameter:
Width: 24mm
Traction compound:
Tires rear:
Make: Orion
Compound: 27B
Insert: Sorex C medium
Traction compound: LRP Grip
Transmission:
Pinion: 21
Spur gear: 93
Final drive ratio: 7,84
Roll-out (mm):
Front axle:
Type: one-way
Diff. setting:
Rear axle:
Type: differential
Diff. setting: medium
Aerodynamics:
Body: Protoform Stratus
Wing: std.
Electrics:
Battery: Orion
Battery capacity (mAh): GP3300SP
Electric motor brand: Revolution
Armature: std.
Winds: 12
Strands: 2
+ Spring: std.
- Spring: std.
Brush face: Serrated
Brush compound: Sprint
Speed controller: LRP Quantum
Limiter (A): Touring Car pr.
Drive frequency (Hz): -
Initial Brake (%): -
Drag brake (on/off): off
Remarks:
Chassis performance: Very fast with plenty of steering...
Re: T1R CARPET SETUP
Originally posted by mikejr718
Yes I have checked there. Only one T1R setup there for outdoor rubber tires. Cant get the search function to show any other t1r setups. Can evo2 setups that use the c-hub suspenion be used on the t1r as they are basicaly the same car???
Yes I have checked there. Only one T1R setup there for outdoor rubber tires. Cant get the search function to show any other t1r setups. Can evo2 setups that use the c-hub suspenion be used on the t1r as they are basicaly the same car???
You just have to click at the set-up link and the only thing you have to change in the search function is the chassis you use (select XRAY T1 RAYCER).
And you'll get 2 pages full of set-ups.
Very handy, and good if you want A basic set-up for a any type of track or conditions.
Tech Elite
iTrader: (16)
130 Plus Size Spur Gears
Who makes spurs in the 128-134 range that fit the xray?
I found PRS but they are out of stock on some sizes.
Any other options.
Jamie
I found PRS but they are out of stock on some sizes.
Any other options.
Jamie
Senna, PRS is the only company I've seen that makes spurs larger than 128.
Rob
Rob
Tech Master
iTrader: (1)
Join Date: Aug 2004
Location: Farmington Hills, MI and proud of it
Posts: 1,059
Trader Rating: 1 (100%+)
what body do you guys use? i like my parma alfa and i am just wondering what you guys think
Tech Master
Parma is the best one out there for carpet and pretty much for any surface. As for asphault, I personally think the Mazda 6 is the best.
T1R CARPET SETUP
Thanks for the help. I was able to view setups on mytsn with your advice on how to search. For some reason when I select a country or a year they dont show up. Thanks
Tech Regular
iTrader: (14)
I was wondering if the set up above will work for the T1 factory kit ?
I am using our normal club set up, and am always looking for something new to try.
We race on high traction carpet, with the normal 27 turn stock motor.
All suggestions welcomed
I am using our normal club set up, and am always looking for something new to try.
We race on high traction carpet, with the normal 27 turn stock motor.
All suggestions welcomed
Tech Master
Go to CEFX.net. You should find some good setups for the FK there.