65LikesTC3 Forum
10-04-2001, 02:15 PM
#287
Tony > you have an order
When are you going to be racing next? I have some different ideas I would like to show you.
When are you going to be racing next? I have some different ideas I would like to show you.
10-04-2001, 03:07 PM
#289
He meant the 357, just a typo.... hahahahaha
10-04-2001, 10:25 PM
#290
JR is the servo to get. The digital one is sweeeet and so smooooth. I love mine and Sean's is even smoother.
In my opinion, JR makes the best servors.
In my opinion, JR makes the best servors.
10-05-2001, 12:44 PM
#292
HEY JACK-
i don't want to sound ignorant, but what is "TTT?"
i don't want to sound ignorant, but what is "TTT?"
10-05-2001, 01:42 PM
#293
TTT = To The Top. It's an old Trinity TechTalk trick to bring the post at the top of the list. If you're not familiar with it, threads get moved to the top of the list when new posts are added and they get deleted when there are no new posts after about 24 hours.
When someone has a thread that no one has been replying to but they don't want it to die, they usually put in a post with "TTT" just to bring it up to the top and save it from being deleted.
When someone has a thread that no one has been replying to but they don't want it to die, they usually put in a post with "TTT" just to bring it up to the top and save it from being deleted.
10-05-2001, 01:48 PM
#294
ahhhhhhh.....eye-c!!!!!!!!
i was trying to figure out if he was replying to someone with a "t.t.f.n." type of thing. no wonder i couldn't figure out who he was answering.
i was trying to figure out if he was replying to someone with a "t.t.f.n." type of thing. no wonder i couldn't figure out who he was answering.
10-05-2001, 01:53 PM
#295
next question: Is there a mask or material suitable for simulating carbon fibre? i just used that rubber shelf stuff. turned out pretty good, but the scale is all wrong and it's really hard to tape to the body and get a clean edge. some places where it gapped left soft mask edges. any tricks-o-da-trade on this kinda pattern?
10-07-2001, 03:05 AM
#297
TC3 Factory Team!
Hi everyone!
This is the first time I am writing in this thread and hope I am not bothering anyone.
At last my TC3 has arrived. Today I went down the track to give it a try for the first time! I was impressed with the handling. It looked like it is so easy to drive. I have to make minor setting alterations but it is looking good.
It is still a bit slower than my MR4 Special but I think that after some adjustments it will be even faster!
Can anyone advise about spur gear and pinion setup for a 5 minute race using a stock motor?
Thanks for your help!
Regards ...
This is the first time I am writing in this thread and hope I am not bothering anyone.
At last my TC3 has arrived. Today I went down the track to give it a try for the first time! I was impressed with the handling. It looked like it is so easy to drive. I have to make minor setting alterations but it is looking good.
It is still a bit slower than my MR4 Special but I think that after some adjustments it will be even faster!
Can anyone advise about spur gear and pinion setup for a 5 minute race using a stock motor?
Thanks for your help!
Regards ...
10-07-2001, 07:02 AM
#298
Senna > What kind of Motor and what pitch are you running? In addition, do you know how big the track is? You need to change to gearing so it is appropriate to the track.
10-07-2001, 02:01 PM
#299
Senna,
Congratulations.
For my reply refer to Malta RC Racers. I've put it all in there already.
Regards
Joe.
Congratulations.
For my reply refer to Malta RC Racers. I've put it all in there already.
Regards
Joe.
