The Speed Passion Thread
Tech Initiate
Reventon LCD
My reventon pro LCD program card will not up date followed the instructions but there is no program in the menu . There is only esc up dates no LCD up dates. Can anyone help. Thanks
Tech Rookie
I have some questions on my reventon R and my 13.5 mmm motor. I uploaded the stock1 software yesterday n everything look find. The boose, brake are very smooth but my motor seems to shaking a bit at one initial point (low rpm) and when it passes that point it ran smooth again. I dont know what happen with the motor and its seem hot compare to my 8.5t hobbywing.
With stock1 software i cant find the way to turn off the boose ( i case i wanna run blinky) or i have to upload different software to run blinky? Is it ok to switch software if u wanna turn off and on the boose?
With stock1 software i cant find the way to turn off the boose ( i case i wanna run blinky) or i have to upload different software to run blinky? Is it ok to switch software if u wanna turn off and on the boose?
Tech Rookie
My set up was
Dssr 3
Boose 30%
Brake 70%
Start rpm 5000
Max rpm 120,000
Delay 0.1s
FDR around 6.5
Dssr 3
Boose 30%
Brake 70%
Start rpm 5000
Max rpm 120,000
Delay 0.1s
FDR around 6.5
Super Moderator
iTrader: (239)
I have some questions on my reventon R and my 13.5 mmm motor. I uploaded the stock1 software yesterday n everything look find. The boose, brake are very smooth but my motor seems to shaking a bit at one initial point (low rpm) and when it passes that point it ran smooth again. I dont know what happen with the motor and its seem hot compare to my 8.5t hobbywing.
With stock1 software i cant find the way to turn off the boose ( i case i wanna run blinky) or i have to upload different software to run blinky? Is it ok to switch software if u wanna turn off and on the boose?
With stock1 software i cant find the way to turn off the boose ( i case i wanna run blinky) or i have to upload different software to run blinky? Is it ok to switch software if u wanna turn off and on the boose?
Super Moderator
iTrader: (239)
Tested an new file yesterday , great power with a 10.5 v3(1cell motor) temps were under 125 all afternoon. Heading to the track again to try different sensor boards getting a set up ready for tomorrow's state race .
Tech Elite
iTrader: (124)
The esc will turn on but wont turn off nor calibrate now with the setup button.
Sidenote: I have tried reinstaller v18 and still does same thing. So I put v19 back on it and same issue no change. Does it need sent in?
Last edited by vr6cj; 10-27-2012 at 02:08 PM.
Super Moderator
iTrader: (239)
So far so good getting better acquainted with the settings , stripped rear belt lol.
Tech Adept
iTrader: (5)
Hey, I have a Reventon R, ran it once so far and noticed it wasn't in blinky mode.
I tried to load the Stock 0 programming, the application detected my ESC and I clicked update, selected stock 0 V18 and then clicked ok, it went through the upload process and completed. I set the brake/drag, then set the voltage cutoff and it said everything was set correctly. Exited the software, disconnected the power and connected it back to my receiver, hooked it up to my lipo and turned it on. Got power to the servo and the fan was running just fine but when I pressed the throttle nothing happens now. Verified it wasn't a radio setting. Turned it off, connected to the programming card, checked settings and instead of just having the basic settings of like 1-11 or whatever it went up to 15 but everything over 11 was set to 0.
I turned it off, disconnected and tried to reconnect to my PC, now the programming card shows SP and then goes to -- and the software never detects the ESC, but the card itself is detected. Connecting it to my car only and then connecting the lipo it does the same thing.
Is it dead? Any special recovery mode I can try? I really hate to have to wait for over a month for it to ship back to wherever it came from and then wait for a new one to arrive. I think setting it to blinky mode should not kill it, Maybe want to look into a fix if any SP employees see this :-P
I tried to load the Stock 0 programming, the application detected my ESC and I clicked update, selected stock 0 V18 and then clicked ok, it went through the upload process and completed. I set the brake/drag, then set the voltage cutoff and it said everything was set correctly. Exited the software, disconnected the power and connected it back to my receiver, hooked it up to my lipo and turned it on. Got power to the servo and the fan was running just fine but when I pressed the throttle nothing happens now. Verified it wasn't a radio setting. Turned it off, connected to the programming card, checked settings and instead of just having the basic settings of like 1-11 or whatever it went up to 15 but everything over 11 was set to 0.
I turned it off, disconnected and tried to reconnect to my PC, now the programming card shows SP and then goes to -- and the software never detects the ESC, but the card itself is detected. Connecting it to my car only and then connecting the lipo it does the same thing.
Is it dead? Any special recovery mode I can try? I really hate to have to wait for over a month for it to ship back to wherever it came from and then wait for a new one to arrive. I think setting it to blinky mode should not kill it, Maybe want to look into a fix if any SP employees see this :-P
Super Moderator
iTrader: (239)
After 12 packs or so it was pretty good . Temperatures were low under 120 with a 10.5. Will post settings tomorrow night
Tech Elite
iTrader: (125)
If anybody is looking for a LCD for their Reventon. I have a spare..pm me.
Tech Apprentice
13.5 Mmm with 20 on the motor geared at 6.77 on a 32m x 14m track using a T3 12.
My GT2.1 was set at;
DRRS 9
START 6000
TIMING BOOST 44
TURBO 20
DELAY 0.3
ACC 400
My Reventon Pro with V19;
DRRS 9
START 6000
HB ACTIVE 70%
HYBRID BOOST 140K
DELAY 0.2
The reventon was 4secs slower. Any suggestions?
My GT2.1 was set at;
DRRS 9
START 6000
TIMING BOOST 44
TURBO 20
DELAY 0.3
ACC 400
My Reventon Pro with V19;
DRRS 9
START 6000
HB ACTIVE 70%
HYBRID BOOST 140K
DELAY 0.2
The reventon was 4secs slower. Any suggestions?
Tech Regular
iTrader: (14)
13.5 Mmm with 20 on the motor geared at 6.77 on a 32m x 14m track using a T3 12.
My GT2.1 was set at;
DRRS 9
START 6000
TIMING BOOST 44
TURBO 20
DELAY 0.3
ACC 400
My Reventon Pro with V19;
DRRS 9
START 6000
HB ACTIVE 70%
HYBRID BOOST 140K
DELAY 0.2
The reventon was 4secs slower. Any suggestions?
My GT2.1 was set at;
DRRS 9
START 6000
TIMING BOOST 44
TURBO 20
DELAY 0.3
ACC 400
My Reventon Pro with V19;
DRRS 9
START 6000
HB ACTIVE 70%
HYBRID BOOST 140K
DELAY 0.2
The reventon was 4secs slower. Any suggestions?
Tech Apprentice
Reventon R
Tried my new Reventon R yesterday, and I'm having issues getting the Drag Brake to function. I'm running the MOD 0, (Forward+Brake+Reverse) V18 B359, and any Percentage that I set the drag brake to, it does not seem to functional at all.
Any advise appriciated
Any advise appriciated
Super Moderator
iTrader: (239)