New Yokomo TC, the BD-5
Anyway, i replied as well. Thanks! 
09-07-2009, 11:35 PM
#1007
jimmy, i think this is good news as got 1 company come out with a DCJ for trf416..so i think this might suit our bd5
www.kkeprc.com
www.kkeprc.com
Last edited by kschu; 09-08-2009 at 01:28 AM.
09-08-2009, 01:42 AM
#1008
Interesting. I only wonder if they will clear the caster block hole. That's why on the 009, the caster block hole is very large. It has to accommodate the movement of the axle joint. If the hole is too small, then the joint will hit. Therefore, it will not work. But if it fits the 416 and works with the stock caster blocks, then it might work with the BD5. How do you get these?
09-08-2009, 02:14 AM
#1009
Interesting. I only wonder if they will clear the caster block hole. That's why on the 009, the caster block hole is very large. It has to accommodate the movement of the axle joint. If the hole is too small, then the joint will hit. Therefore, it will not work. But if it fits the 416 and works with the stock caster blocks, then it might work with the BD5. How do you get these?
they selling around usd45/pair....
is that mean our bd5 can use it ???
09-08-2009, 02:16 AM
#1010
09-08-2009, 02:25 AM
#1011
09-08-2009, 02:56 AM
#1012
double joint cvds are definately not necessary
they just create understeer ... that's it
rather spend your money on hard suspension parts as those actually increase the cars performance
they just create understeer ... that's it
rather spend your money on hard suspension parts as those actually increase the cars performance
09-08-2009, 02:34 PM
#1013
09-16-2009, 05:38 AM
#1015
New!!! BD5 Option Parts From Yokomo Japan
BD-002P Main Chassis for BD5 ( Straight Pack)
BD-003CS Upper Deck Set for BD5 Square Type Battery
BD-201R8 Center Link For BD5 (8mm Type)
BD-301FF2 Aluminum Front Suspension Arm Mount for BD5 (Front
42mm)
BD-301FR2 Aluminum Front Suspension Arm Mount for BD5 (Rear 42mm)
BD-301RF1 Aluminum Rear Suspension Arm Mount for BD5 (Front 41.3mm)
BD-302FL1 Front Bulkhead Cap (Left) 3.5mm Wide I Arm Pivot
BD-302FR1 Front Bulkhead Cap (Right) 3.5mm Wide I Arm Pivot
BD-302RL1 Rear Bulkhead Cap (Left) 3.5mm Wide I Arm Pivot
BD-302RR1 Rear Bulkhead Cap (Right) 3.5mm Wide I Arm Pivot
Source: H²
BD-002P Main Chassis for BD5 ( Straight Pack)
BD-003CS Upper Deck Set for BD5 Square Type Battery
BD-201R8 Center Link For BD5 (8mm Type)
BD-301FF2 Aluminum Front Suspension Arm Mount for BD5 (Front
42mm)
BD-301FR2 Aluminum Front Suspension Arm Mount for BD5 (Rear 42mm)
BD-301RF1 Aluminum Rear Suspension Arm Mount for BD5 (Front 41.3mm)
BD-302FL1 Front Bulkhead Cap (Left) 3.5mm Wide I Arm Pivot
BD-302FR1 Front Bulkhead Cap (Right) 3.5mm Wide I Arm Pivot
BD-302RL1 Rear Bulkhead Cap (Left) 3.5mm Wide I Arm Pivot
BD-302RR1 Rear Bulkhead Cap (Right) 3.5mm Wide I Arm Pivot
Source: H²
09-16-2009, 07:17 AM
#1017
it's meant for stickpack style batteries and therefore doesn't use any battery tape whatsoever but a battery strap with additional plastic mounts
09-16-2009, 07:17 AM
#1018
That Chassis is design for Straight pack Sub C battery, not design for Lipo.
You need to do some modification to fit the Lipo into this chassis.
For Lipo battery, is recommended to use the original chassis with the new upper deck.
You need to do some modification to fit the Lipo into this chassis.
For Lipo battery, is recommended to use the original chassis with the new upper deck.
09-16-2009, 07:47 AM
#1019
standard chassi, standard topdeck for lipo
or p-chassi with new topdeck .... but then you need to use a lipo with no battery placement thingis
or p-chassi with new topdeck .... but then you need to use a lipo with no battery placement thingis
09-16-2009, 09:37 AM
#1020