Tamiya TRF415
i am trying to find my internal ratio on my msx stock is 2.187. i am running the black pulleys front and rear and have the wide aluminum 16 tooth in the center.
Tech Addict
iTrader: (2)
kentech,
thanks a bunch.
cheers.
thanks a bunch.
cheers.
Tech Fanatic
iTrader: (3)
Does anyone know if this TAO5 Steering block will work on the 415 MRE?
http://shopping.rcmodel.hk/product_i...oducts_id=7460
http://shopping.rcmodel.hk/product_i...oducts_id=7460
Originally Posted by robsxxxs
i am trying to find my internal ratio on my msx stock is 2.187. i am running the black pulleys front and rear and have the wide aluminum 16 tooth in the center.
Also you can make that internal ratio change on the MSX, just run the new alternated pulleys that are for the MRE. It fits, just set the bearing holders to make the belt as loose as it can be.
RC Hard Turnbuckle Shaft Set - DF-03 3x42mm Item #53942
Is this set of HARD turnbuckle set for the DF-03 just like titanium or black steel w/ the blue alum collars? Thinking of getting this instead of the 3x42mm Ti turnbuckles (which are hard to find aside from what Lungsford has avail & 3Racing - which are out of stock on their website).
Tech Master
Originally Posted by JRRobiso
I'm the same as well w/ you Ben. Just waiting for the alum airduct too. That's the only thing that's missing right now on my MRE. A week ago I tried a mock-up for the electronics to see if everything was working properly w/ the batt in it & was tempted to put my ESC & RX (Hara Twister 2.1 & Spektrum combo) w/ dbl sided tape but could not find enough contact surface for the ESC due to the small footprint of the unit. Was thinking of making an airduct myself w/ lexan (somebody has done it, I think a few pages back) but held off. I'll just wait for alum airduct instead & also thinking of installing/changing my Spektrum RX to the Micro version (which even has a smaller footprint than my ESC). Might as well find someone who carries the Titanium turnbuckets for the steering arms while I wait for the release of the airduct.
I've done a lexan airduct...But would want the alu one. In terms of strength "Aluminium VS Lexan", this is a no brainer.Wouldn't it to come a part in a hard crash sending my expensive ESC dragging on the tarmac.
Originally Posted by Tek Nickal
The internal ratio is actually the same, you didn't change anything by running the fixed pulley. The internal ratio is calculated by dividing the big pulley, by the smaller one, in this case 35/16 = 2.187
Also you can make that internal ratio change on the MSX, just run the new alternated pulleys that are for the MRE. It fits, just set the bearing holders to make the belt as loose as it can be.
Also you can make that internal ratio change on the MSX, just run the new alternated pulleys that are for the MRE. It fits, just set the bearing holders to make the belt as loose as it can be.
thanks that helps me out alot.
Here are a couple of more pics of the MSXX.
I noticed that it will sell for ~40000 yen in Japan which is around 6000 yen lower than the MRE.
I noticed that it will sell for ~40000 yen in Japan which is around 6000 yen lower than the MRE.
Tech Fanatic
iTrader: (3)
Originally Posted by tbeardmore
Does anyone know if this TAO5 Steering block will work on the 415 MRE?
http://shopping.rcmodel.hk/product_i...oducts_id=7460
http://shopping.rcmodel.hk/product_i...oducts_id=7460
Anyone......?????????????
Tech Champion
iTrader: (4)
thoose are for the std suspension, not the LWT suspension that comes with all the cars from MS onwards (MS, MSX, MRE, MSXX....)
Tech Master
iTrader: (92)
I personally like the look of the new top deck. It gives the car a little extra character. And look how far the cut-out goes back on it...looks like lots of flex.
Tech Regular
Can someone verify if the MSXX lower deck is the same as MRE? The bumper mount is new so I want to know if it uses the same lower deck. I was about to order a new MRE lower deck but when I heard about the MSXX, I need to know if I should order one now.
Originally Posted by trf_racer
Can someone verify if the MSXX lower deck is the same as MRE? The bumper mount is new so I want to know if it uses the same lower deck. I was about to order a new MRE lower deck but when I heard about the MSXX, I need to know if I should order one now.
Originally Posted by tbeardmore
Does anyone know if this TAO5 Steering block will work on the 415 MRE?
http://shopping.rcmodel.hk/product_i...oducts_id=7460
http://shopping.rcmodel.hk/product_i...oducts_id=7460
Tech Master
Originally Posted by trf_racer
Can someone verify if the MSXX lower deck is the same as MRE? The bumper mount is new so I want to know if it uses the same lower deck. I was about to order a new MRE lower deck but when I heard about the MSXX, I need to know if I should order one now.
Not very sure about whether the MSXX chassis is machined differently from the MRE. But quite sure that the quality of the MRE grahite weaving is better than the MSXX chassis.