Inspire us. Show me your BEST, CLEANEST electronics installation pics.
#1231
Tech Adept
nice
#1232
#1233
Nice
Very nice, but where is your sensor wire?
#1235
Tech Initiate
Good question, forgot to fit it at the time photos were taken, however it's still inkeeping with the look.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
#1236
Tech Initiate
Good question, forgot to fit it at the time photos were taken, however it's still inkeeping with the look.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
#1237
Good question, forgot to fit it at the time photos were taken, however it's still inkeeping with the look.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
#1238
some good stuff in here! getting some good ideas for rewiring
#1239
Tech Elite
iTrader: (267)
Good question, forgot to fit it at the time photos were taken, however it's still inkeeping with the look.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
Since then I now have a Novak Sentry fitted too with home made wiring loom ( took alot of making trying to keep it neat and easily removable ), there's loads of wires when fitting a telemetry system and though it looks more busy now it's still very minimal and of course co-ordinated.
#1241
#1242
R/C Tech Elite Member
iTrader: (69)
I seen the Serpent S120 pic got downloaded more than the Gen XL. Hope it's not being saved as an example of what NOT to do. For the record I didn't see the XL posted by rpoage till after I posted. Pretty similar... are you getting any bind with the motor wires under there? Does that car get run?
#1243
BMI CopperHead 12 with new front end. Perfectly balanced.
PT under the servo.
For your judgement
PT under the servo.
For your judgement
#1244
A recent toy conversion, and how I stashed a RX.
#1245
Tech Regular
Here is my TC6!
Savox 1251mg servo - Sanwa RX451R receiver - Speed Passion GT2.1 esc - Speed Passion V3 motor - the black box is an AMB PT wrapped in black heatshrink tube
Savox 1251mg servo - Sanwa RX451R receiver - Speed Passion GT2.1 esc - Speed Passion V3 motor - the black box is an AMB PT wrapped in black heatshrink tube
Last edited by Fastfreddy74; 01-25-2011 at 06:19 AM.