Warpspeed Demon and Demon 2
#2461
Tech Master
When I went from TC3 FT to an IRS TC3 with Trinity alluminum chassis braces you really have to lighten up your springs several steps. My personal preference is the bone stock TC3-FT though
Good thing about a good, solid CF chassis...It will NOT tweak
Good thing about a good, solid CF chassis...It will NOT tweak
#2462
GTIracer guess your a VW freak also!
When the guys say the barry baker tc3 is stock its not true they mill the chassis and perform other types of surgery that isnt visible to the untrained eye!
The deamon aides with the stiffness and elimination of the tourqsteer its also a car that is smoother aswell as consistant to drive.
One big thing is the the batteries are set closer inboard for balance and your not going to worry that after 2 runs your chassis is tweaked because of motor heat.
GtI racer I promise you you wont be disappointed!
When the guys say the barry baker tc3 is stock its not true they mill the chassis and perform other types of surgery that isnt visible to the untrained eye!
The deamon aides with the stiffness and elimination of the tourqsteer its also a car that is smoother aswell as consistant to drive.
One big thing is the the batteries are set closer inboard for balance and your not going to worry that after 2 runs your chassis is tweaked because of motor heat.
GtI racer I promise you you wont be disappointed!
#2463
Tech Master
iTrader: (1)
Racing was good yesterday. One rain storm during the qualifiers, we dried the track and went back to racing. PW and the entire crew were real tough in the mod class. They ran an A and B in mod. I'm getting the new car to work better and enjoying it more. One more week to get everything dialed in before going over to Kissimee. Hector see you over there Friday night.
#2464
Tech Apprentice
Yea I loove VEE Dubs.. As for Barrys car, i meant basicly stock.Everyone mills the chassis to move the battries closer to centerline. But main his car is close to stock. Aside from Losi steering block most if not all of the Team drivers have the stock steerring set up
So for the 200.00 is it going to be a much better car, just a more refined car, or a lot of eye candy cause it is nice to look at
So for the 200.00 is it going to be a much better car, just a more refined car, or a lot of eye candy cause it is nice to look at
#2465
my beloved vw bretheren!
the car is more then eye candy. it does everything where the factory team kit left off. I promise you! you wont be disappointed!
the car is more then eye candy. it does everything where the factory team kit left off. I promise you! you wont be disappointed!
#2466
Tech Adept
Does warpspeed have holes drilled for some type of nerf wings..
You know in front of the rear wheels?
You know in front of the rear wheels?
#2467
No, but it would be easy to drill them...you just need to heat up and bend the brp wings flat.
#2468
Hi
Could someone please post or provide a link to the WarpSpeed 12 scale chassis?
Thanks!!!
Thanks!!!
#2469
Here it is.
http://rctech.net/forum/showthread.p...701#post788701
You might have to scroll down the page to get to it!!
http://rctech.net/forum/showthread.p...701#post788701
You might have to scroll down the page to get to it!!
#2470
Originally posted by lmunno
Here it is.
http://rctech.net/forum/showthread.p...701#post788701
You might have to scroll down the page to get to it!!
Here it is.
http://rctech.net/forum/showthread.p...701#post788701
You might have to scroll down the page to get to it!!
In English: Thank You Very Much!!!!!
#2471
lem2: Glad I could help you out!! Victor brought the 12th scale to the track a while back it was very nice done in the satin c/f.
#2473
Tech Master
iTrader: (1)
Hurricane Charlie seems to have spared us and has come ashore south of the Tampa-Bay area. We should all be racing this Sunday again. With the state series race next weekend we will get one more chance at gettting every thing dialed in. Hope you can make it down , Victor.
#2474
kansasracer there is a warpspeed Mi2 its a prototype at this time.