Tekin RS ESC sensored
M05 setup
Hey guys
Anyone put their tekin in a tamiya mini?
I could use a starting point for 13.5 in a m05 on carpet indoors. Any advice appreciated.
Cheers in advance
Paul
Anyone put their tekin in a tamiya mini?
I could use a starting point for 13.5 in a m05 on carpet indoors. Any advice appreciated.
Cheers in advance
Paul
Is this right?
Just finished up putting my SC10 together. I've been out of the hobby for almost a decade and was curious if my set-up was working correctly. Using a Tekin RS with a Novak Ballistic 17.5 motor, Spektrum 3100 receiver, 15/87 gearing.
Watch this video and tell me if this looks normal to you…just seemed kinda slow to me, but like I said, been out of the sport a while.
Thanks for your input,
AJ
http://gallery.me.com/ajnealey#100085
Watch this video and tell me if this looks normal to you…just seemed kinda slow to me, but like I said, been out of the sport a while.
Thanks for your input,
AJ
http://gallery.me.com/ajnealey#100085
Tech Elite
iTrader: (26)
Just finished up putting my SC10 together. I've been out of the hobby for almost a decade and was curious if my set-up was working correctly. Using a Tekin RS with a Novak Ballistic 17.5 motor, Spektrum 3100 receiver, 15/87 gearing.
Watch this video and tell me if this looks normal to you…just seemed kinda slow to me, but like I said, been out of the sport a while.
Thanks for your input,
AJ
http://gallery.me.com/ajnealey#100085
Watch this video and tell me if this looks normal to you…just seemed kinda slow to me, but like I said, been out of the sport a while.
Thanks for your input,
AJ
http://gallery.me.com/ajnealey#100085
ROAR SCT 17.5 Tekin setup sheet
EDIT: Watching that video it looks like you've got massive drag brake on there. With the setup above, you'll have to be careful free-revving it like that as the tires can separate from the rim.
Thank you very much for the quick response. Made the changes…especially to the gearing…and it's a crapton faster!
Thanks again and can't wait to hit the track.
AJ
Thanks again and can't wait to hit the track.
AJ
Tech Elite
iTrader: (26)
No problem. just be sure to check motor temp every couple minutes until you're comfortable that you can go the distance without overheating. On most tracks that setup will be fine -- even a bit conservative.
1/12 17.5 and wgt 13.5
does anyone have a good starting point for 208 no boost, no timing for 1/12 17.5 and wgt 13.5...running speedpassion v3 motor...i need a rollout for a 40x100ft track and a 30x70ft track.
Tech Master
iTrader: (3)
Join Date: Nov 2001
Location: Land of high taxes and bad football
Posts: 1,807
Trader Rating: 3 (100%+)
Tech Champion
iTrader: (34)
85+ roll, you may want to crank some endbell timing up to get top end also.
Tech Rookie
I have an RS and just finished updating to the 208 software. I cannot find any instructions for setting the ESC into Spec mode. Any help would be appreciated.
Thanks
Jeff
Thanks
Jeff
Tech Lord
iTrader: (103)
using the hot wire click throttle and #1 on the slider,using the pit mode go the TP then INS to #1led
Tech Elite
iTrader: (11)
hotwire
Will the hotwire software install on a PS3?
Thats the only pc that I have. lol The rest are mac's.
Thanks for your help.
Thats the only pc that I have. lol The rest are mac's.
Thanks for your help.
Tech Lord
iTrader: (103)
there is a way to use it on a mac,some one else will have to help you
Iwould like a set up for 1/12th with a 10.5 SP v3 motor and the track has a 25m long straight and flowing but tight infield
including some idea for roll out , i have been running today and the motor is cold
final settings were
Start 4,XXX
End 18,XXX
boost 35
Turbo 5
delay 0.15
ramp 2.0
roll out 45 ish
push control 5
drag off
brake max
throttle profile 3
Thanks Phil
including some idea for roll out , i have been running today and the motor is cold
final settings were
Start 4,XXX
End 18,XXX
boost 35
Turbo 5
delay 0.15
ramp 2.0
roll out 45 ish
push control 5
drag off
brake max
throttle profile 3
Thanks Phil
Tech Addict
Iwould like a set up for 1/12th with a 10.5 SP v3 motor and the track has a 25m long straight and flowing but tight infield
including some idea for roll out , i have been running today and the motor is cold
final settings were
Start 4,XXX
End 18,XXX
boost 35
Turbo 5
delay 0.15
ramp 2.0
roll out 45 ish
push control 5
drag off
brake max
throttle profile 3
Thanks Phil
including some idea for roll out , i have been running today and the motor is cold
final settings were
Start 4,XXX
End 18,XXX
boost 35
Turbo 5
delay 0.15
ramp 2.0
roll out 45 ish
push control 5
drag off
brake max
throttle profile 3
Thanks Phil
I've not run it for a while now though.
Tech Elite
iTrader: (15)
Can someone please PM me a link to download the Hotwire 4 software so I can downgrade back to v203? Thank you!