Tekin RS ESC sensored
Tech Master
Here's a question for all of you seasoned vets. I run 1/12 17.5 1c and I have been fighting the car droping of .8 to a full 1 second in the last 2 min. The frist 4-5 min the car rips like crazy. What is your expirence of fading? some guys at the club seem to be able to knock the fade down to .3 or .4. Here are my settings
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Here's a question for all of you seasoned vets. I run 1/12 17.5 1c and I have been fighting the car droping of .8 to a full 1 second in the last 2 min. The frist 4-5 min the car rips like crazy. What is your expirence of fading? some guys at the club seem to be able to knock the fade down to .3 or .4. Here are my settings
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Tech Master
I think that you are geared to heavy.
I don't now what timing is now on the motor but I think that you can better set it lower.
Also this will make that you don't have a to high timing.
I thought ad the standard mark that it was 10 if i'm correct.
I don't now what timing is now on the motor but I think that you can better set it lower.
Also this will make that you don't have a to high timing.
I thought ad the standard mark that it was 10 if i'm correct.
Tech Legend
iTrader: (294)
so I am not sure where you are seeing this at but that is what is going on with hotwire software.
Also when I decheck 1S lipo, and apply settings, it still is retaining the 1S lipo setting as being checked. I got it to go away but I had to pick default setting and reset everything.
I also sometimes get a error with some Debug info from software.
Ok, I'll try decreasing the gearing. Thanks!
Tech Master
Amyone knows the best setting for orion 11.5t? My fav fdr is 7.7 - 9. Drag brake 0, reverse off, motortype 1, throttle 3-4, limiter 2, push 70, boost 20-30, turbo 15-40, delay 0, ramp 2, start 4xxx end 17xxx -19xxx. Respond on straight is very easy but in the inside corners i felt the lack of torque. My other problem is after acceleration on long straight it felt like theres drag brakes which slowed me down too much where the other cars manage to close down on me. Is the push button doing that cos i know when u off it, the drag brake felt even stronger. So any fine settings to help me out here?. Temps 71degC 5min. Looking to maximise to 80degC
Tech Master
Amyone knows the best setting for orion 11.5t? My fav fdr is 7.7 - 9. Drag brake 0, reverse off, motortype 1, throttle 3-4, limiter 2, push 70, boost 20-30, turbo 15-40, delay 0, ramp 2, start 4xxx end 17xxx -19xxx. Respond on straight is very easy but in the inside corners i felt the lack of torque. My other problem is after acceleration on long straight it felt like theres drag brakes which slowed me down too much where the other cars manage to close down on me. Is the push button doing that cos i know when u off it, the drag brake felt even stronger. So any fine settings to help me out here?. Temps 71degC 5min. Looking to maximise to 80degC
Boost 50
Turbo 10
Turbo delay 0,5
Turbo ramp 2
Throttle 3
Start RPM 5000
End RPM 16000
Play also with your gearing. A good infield speed will be reached by the right gearing.
You don't have to reach a motor temp of 80C.
The motor temp you have now is good.
I don't now the motor timing but if possible set it a bit lower.
First gear for the infield and play with the Boost around 45 to 50.
Later ad the Turbo. I think 10 will be enough.
Here's a question for all of you seasoned vets. I run 1/12 17.5 1c and I have been fighting the car droping of .8 to a full 1 second in the last 2 min. The frist 4-5 min the car rips like crazy. What is your expirence of fading? some guys at the club seem to be able to knock the fade down to .3 or .4. Here are my settings
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Timing 48
Turbo 4
Delay .5
End 7000
Start 2500
rollout 75
Thanks for any help and suggestions guys!
Timing 30
Turbo Max
Delay .5
Ramp 1.0
End 7500
Start 1500
rollout 75
It wasn't perfect but it didn't fade noticeably at all. The infield was great but I would have liked the turbo to come in a little quicker. I might try lowering the end rpm to 7000 and the delay to .3.
.Delay
Delays slowed my acceleration on the early straight n accelartion out of corners. Our straights is only 30m.
Thinking of using fdr 9-11 . Recmended settings pls?
Tech Lord
iTrader: (103)
I just took a look again and the only option I have is to enter the end RPM value, and then hit caculate and it gives me a list of starting RPMs.
so I am not sure where you are seeing this at but that is what is going on with hotwire software.
Also when I decheck 1S lipo, and apply settings, it still is retaining the 1S lipo setting as being checked. I got it to go away but I had to pick default setting and reset everything.
I also sometimes get a error with some Debug info from software.
so I am not sure where you are seeing this at but that is what is going on with hotwire software.
Also when I decheck 1S lipo, and apply settings, it still is retaining the 1S lipo setting as being checked. I got it to go away but I had to pick default setting and reset everything.
I also sometimes get a error with some Debug info from software.
Amyone knows the best setting for orion 11.5t? My fav fdr is 7.7 - 9. Drag brake 0, reverse off, motortype 1, throttle 3-4, limiter 2, push 70, boost 20-30, turbo 15-40, delay 0, ramp 2, start 4xxx end 17xxx -19xxx. Respond on straight is very easy but in the inside corners i felt the lack of torque. My other problem is after acceleration on long straight it felt like theres drag brakes which slowed me down too much where the other cars manage to close down on me. Is the push button doing that cos i know when u off it, the drag brake felt even stronger. So any fine settings to help me out here?. Temps 71degC 5min. Looking to maximise to 80degC
Would anybody have a fast setup that won't fry the motor. I run on a small track with a medium straightaway. I am running a tamiya 416 we with tekin v 203 thunderpower 5200 mah 50c, lrp x-12 17.5, 100t spur, and 30t pinion? Please help me out.