Tekin RS ESC sensored
#8881
Tech Regular
Cool thanks for that. Im affraid I have lots of questions so be prepared.
Can I update the esc before I put it in the car YES
Does it have to be callibrated to my futaba hand controller 1st before I can update the esc to v200 NO
Also does the esc need to connected to a battery and the radio receiver to be updated NO
Will it run off the power from my lap top.YES
HTH
Can I update the esc before I put it in the car YES
Does it have to be callibrated to my futaba hand controller 1st before I can update the esc to v200 NO
Also does the esc need to connected to a battery and the radio receiver to be updated NO
Will it run off the power from my lap top.YES
HTH
#8882
Tech Regular
Well I connected the speedo to the hotwire for the 1st time, A green light on the hotwire and a flickering red light in the middle of the speedo. The on screen menu had boost delay down to 0.2 so I guess this is the V200 software. does it tell you what software its got on the speedo ? sorry for all the questions everyone lol
#8883
Tech Master
iTrader: (8)
Well I connected the speedo to the hotwire for the 1st time, A green light on the hotwire and a flickering red light in the middle of the speedo. The on screen menu had boost delay down to 0.2 so I guess this is the V200 software. does it tell you what software its got on the speedo ? sorry for all the questions everyone lol
#8884
Tech Apprentice
Hi i´m new to tekin products
Can i get some help in setting up a rs to a smal track 70" straight
i run tc with an lrp x12 17.5 motor on rubber tires should i go for the tekin 17.5?
right now i run an lrp spx fdr 5.2 and -5 timing if that will help to now the track a little.
best regards
Martin
Can i get some help in setting up a rs to a smal track 70" straight
i run tc with an lrp x12 17.5 motor on rubber tires should i go for the tekin 17.5?
right now i run an lrp spx fdr 5.2 and -5 timing if that will help to now the track a little.
best regards
Martin
#8885
Hi i´m new to tekin products
Can i get some help in setting up a rs to a smal track 70" straight
i run tc with an lrp x12 17.5 motor on rubber tires should i go for the tekin 17.5?
right now i run an lrp spx fdr 5.2 and -5 timing if that will help to now the track a little.
best regards
Martin
Can i get some help in setting up a rs to a smal track 70" straight
i run tc with an lrp x12 17.5 motor on rubber tires should i go for the tekin 17.5?
right now i run an lrp spx fdr 5.2 and -5 timing if that will help to now the track a little.
best regards
Martin
For a 70' straight, you might start around a 5.5 FDR with some conservative timing settings [zero on the motor, adjust on the RS with hotwire], and see what your temps are doing.
The LRP motor should be fine.
Is there a leading sweeper to the straight, or at the end of the straight that would give you more full throttle time than just 70'? Turbo will be your friend if so.
#8886
Tech Apprentice
thanks for the help.
yes there is a sweeper into the straight.
i will go back to see your set-up
yes there is a sweeper into the straight.
i will go back to see your set-up
Last edited by MartinBasse; 12-22-2009 at 04:22 PM.
#8887
Tech Fanatic
iTrader: (23)
Need some help please. I just picked up a used RS Pro and it did not have the capacitor with it. I know that I need to run a cap, but curious what the rating needs to be to avoid any issues. I'm running it in 1/12 scale 13.5/lipo if that makes any difference.
I checked the web site but could not find any specific info on what is needed. I have an older cap rated at 16v, 680 uf that I can use if that will work. I really want to get the car set up before race day and don't have a hobby shop close by that can help. If the one I have is not correct, I could go to an electronics store.
Thanks for any help!
I checked the web site but could not find any specific info on what is needed. I have an older cap rated at 16v, 680 uf that I can use if that will work. I really want to get the car set up before race day and don't have a hobby shop close by that can help. If the one I have is not correct, I could go to an electronics store.
Thanks for any help!
#8888
Tech Champion
iTrader: (159)
Need some help please. I just picked up a used RS Pro and it did not have the capacitor with it. I know that I need to run a cap, but curious what the rating needs to be to avoid any issues. I'm running it in 1/12 scale 13.5/lipo if that makes any difference.
I checked the web site but could not find any specific info on what is needed. I have an older cap rated at 16v, 680 uf that I can use if that will work. I really want to get the car set up before race day and don't have a hobby shop close by that can help. If the one I have is not correct, I could go to an electronics store.
Thanks for any help!
I checked the web site but could not find any specific info on what is needed. I have an older cap rated at 16v, 680 uf that I can use if that will work. I really want to get the car set up before race day and don't have a hobby shop close by that can help. If the one I have is not correct, I could go to an electronics store.
Thanks for any help!
#8890
when using this speedo what changes were made on the speedo or timing setting using a 17.5 ballistic and trinity duo
#8891
losing power
i need help...i have my tekin rs in my wgt and it is pretty quick the first 6 to 8 laps...i have a ea duo 2, tekin, 82.90 rollout, and an intellect 40 c battery.. the track is 70 x 35...when i begin a run the car is a bullet...9.1, 9.2, after 6 to 8 laps...all i can get is 9.5, 9.6, 9.7...what could be the problem...someone anyone let me know...is it gearing, setup, or what...the motor does not get hot..there is not timing in the motor...the esc setup is as follows
turbo boost...max
timing boost...3
throttle profile...4
drag brake ...0
push....50
delay.... .5
turbo boost...max
timing boost...3
throttle profile...4
drag brake ...0
push....50
delay.... .5
#8892
What radio are you using? Are you using 200 software?
Where is the motor timing set?
Where is the motor timing set?
#8894
losing power
the motor timing is set at 0
i am running a dx3s
i am running v200
i am running a dx3s
i am running v200