Tekin RS ESC sensored
Tech Rookie
how do you know what max rpm to use?
Tech Master
It depends on the track and what you want for a feeling.
A higher End RPM makes the acceleration smoother.
You can gear a bit heavier and you can ad more Boost.
With a lower End RPM your car will accelerate faster.
I play with it till I have a good feeling.
A higher End RPM makes the acceleration smoother.
You can gear a bit heavier and you can ad more Boost.
With a lower End RPM your car will accelerate faster.
I play with it till I have a good feeling.
Tech Fanatic
iTrader: (6)
i want to give a big shout-out to m-technic for helping me out this saturday with my rs setup. my first run with the rs came in at over 200 degrees and after he made some adjustments it temped at under 130!!! i ended the night with an fdr of 4.7 but it still kept temping at 130 and i went up 3 teeth higher than before so i know my 416x could have been faster
thanks tj
thanks tj
Tech Adept
iTrader: (10)
Sounds like a plan .. i should have asked for help earlier .. hope its not too late... now i understand why starting turbo at 5.
With trying 6 - 6.5 - 7 fdr temps in theory should go down if i dont make any changes on the esc ?
Mikky32 i will also try your suggestion. I will keep note of temps and report back.. maybe this may help other newbies like me.
thanks !
With trying 6 - 6.5 - 7 fdr temps in theory should go down if i dont make any changes on the esc ?
Mikky32 i will also try your suggestion. I will keep note of temps and report back.. maybe this may help other newbies like me.
thanks !
here was my setup during the final qualifying. 6 min
FDR : SRPM : ERPM : TIMING : TURBO : DELAY : RAMP : Final Temp
6.551470588 2000 10000 50 5 0.3 3 130
i find that the car was more on the smooth side and did flat out almost 1/8 before the end of the straight.. it was not too bad. it made me calmer infield puch was average but controllable
Final Setting i only put the timing to max and turbo to 8 ( i know its a weird number lol) end temparature was 140 - 145
i found that the car slingshots all the way at the end and i was smiling at the straight infield was a tad more aggressive.
have a great day ! and hope this helps...
Tech Adept
iTrader: (10)
i want to give a big shout-out to m-technic for helping me out this saturday with my rs setup. my first run with the rs came in at over 200 degrees and after he made some adjustments it temped at under 130!!! i ended the night with an fdr of 4.7 but it still kept temping at 130 and i went up 3 teeth higher than before so i know my 416x could have been faster
thanks tj
thanks tj
thanks!
Tech Fanatic
iTrader: (6)
kp-61 i'll get the setup on here as soon as i can i still have to unpack my stuff, i worked non-stop all week to make up hours at work for saturdays race so im kinda taking a break right now but i will post it.
by the way my motor was a redline 17.5 and my gearing was 92/40 and i used the 200 software for the class i ran, the 203 would've been illegal. the redline motor was very fast with the 203 software though!
by the way my motor was a redline 17.5 and my gearing was 92/40 and i used the 200 software for the class i ran, the 203 would've been illegal. the redline motor was very fast with the 203 software though!
Tech Lord
iTrader: (103)
kp-61 i'll get the setup on here as soon as i can i still have to unpack my stuff, i worked non-stop all week to make up hours at work for saturdays race so im kinda taking a break right now but i will post it.
by the way my motor was a redline 17.5 and my gearing was 92/40 and i used the 200 software for the class i ran, the 203 would've been illegal. the redline motor was very fast with the 203 software though!
by the way my motor was a redline 17.5 and my gearing was 92/40 and i used the 200 software for the class i ran, the 203 would've been illegal. the redline motor was very fast with the 203 software though!
Tech Fanatic
iTrader: (6)
yea i ran rcgt, it was a lot of fun but watching the 13.5 class going at it made me want to run that instead.
ok i got my setup up...
drag brake - 20
brake strength - 100
neutral width - 5
throttle profile - 5
timing boost - 20
turbo boost - 15
turbo delay - 0.2
ok i got my setup up...
drag brake - 20
brake strength - 100
neutral width - 5
throttle profile - 5
timing boost - 20
turbo boost - 15
turbo delay - 0.2
Tech Elite
iTrader: (19)
i saw it mentioned before by Randy to run a minimum of delay at 0.2
how do you find it at 0 ?
i ran 0.4 but i can see advantages at 0.2 as the speed down the striaght, once you back off due to slower car (most cars) the process starts again. Cheers.
how do you find it at 0 ?
i ran 0.4 but i can see advantages at 0.2 as the speed down the striaght, once you back off due to slower car (most cars) the process starts again. Cheers.
Randy mentioned previously that due to the low start rpm you can get away with the 0 delay. I tried it and had absolutely no problems with heat or overtiming and this was with a Novak motor on standard timing.
Car was still very punchy but was also very smooth in its power delivery, not to mention that it also had a lot of top end speed. As I mentioned prior I was able to hang with 4.5 mod cars with this set up
Car was still very punchy but was also very smooth in its power delivery, not to mention that it also had a lot of top end speed. As I mentioned prior I was able to hang with 4.5 mod cars with this set up
Last edited by B4james; 02-22-2010 at 03:10 AM.
Tech Adept
I tried delay=0 with a 11.5R motor. The speed is very fast, it can hang around with 5.5R's. However, I do find the motor temp. to be higher than usual (around 70C to 75C).
With a delay<>0 with 11.5R, the temp is around 50ish C.
With a delay<>0 with 11.5R, the temp is around 50ish C.
Hi guys, just a few questions. What are the differences between the DUO1 and DUO2 motors when used with the Tekin and the new 203 software. Which do people find has more RPM and which more Torque? Do they have to be geared differently for use on the same track? or Some settings run a bit softer/ harder between the two motors?
Any help would be great.
Cheers
Any help would be great.
Cheers
Tech Elite
iTrader: (29)