Tekin RS ESC sensored
#7576
Tech Regular
Since I got my RS and Hotwire I have been messing around with my settings a lot and trying new things with it. I was curious what other people have been using as far as settings go with similar setups for 1/12 scale cars. I am running the Tekin RS v200 firmware, Fantom Ion2 17.5 (Trinity Duo 2 based) and SMC 50c 4900 single cell lipo. Any ESC setup, motor timing and rollout suggestions would be helpful. 80 ft x 48 ft track, medium to high traction.
#7577
The Vegas version offers the delay to go down to .2 seconds.
The turbo does "hold" if you lift slightly while on. During this event we're "waiting" a bit to see if you come back on throttle. If you do we recover on turbo in the appropriate amount.
The turbo does "hold" if you lift slightly while on. During this event we're "waiting" a bit to see if you come back on throttle. If you do we recover on turbo in the appropriate amount.
#7578
Tech Elite
iTrader: (32)
I just gotten my RS PRO esc, but i dun seem to be able to update to v200 from HotWire. Will somebody help?
My email address is [email protected]
My email address is [email protected]
#7579
Can I have V200 Vegas Edition too?... Need all the tweaking I can get...
#7580
Please put me on that list for the Vegas version. Our track here in Hawaii is very close in length to the iic track and a .2 or .3 delay would be perfect!
[email protected]
Thanks!!
#7581
I would expect a standard setup of 10 on the motor, 15 on timing boost with some turbo.
You may end up changing your roll out. Track demensions would be helpful.
Also guys, we're going to release the "Vegas" software for all. I've had a ton of requests for it. This isn't the last word from us for now though...there is more to come.
You may end up changing your roll out. Track demensions would be helpful.
Also guys, we're going to release the "Vegas" software for all. I've had a ton of requests for it. This isn't the last word from us for now though...there is more to come.
add me to the Vegas Software list please
#7582
Could you send me the Vegas version as well please??
#7583
Tech Adept
#7584
#7585
Ooopss... sorry I started this Randy..
#7586
Suggestion,
Why don't you just PM Randy and then leave the thread for discussion.
Regards,
Calvin.
Why don't you just PM Randy and then leave the thread for discussion.
Regards,
Calvin.
#7587
our track so small I use no delay
like orca esc full throttle turbo kicks
like orca esc full throttle turbo kicks
#7588
Tech Adept
Just downloaded the vegas 200 version from TQ racing site. All I can say is thanks Randy, glad I bought the Tekin(s).
http://www.tqcells.com/Hotwire200.zip
Link is courtousy of TQ Steve.
http://www.tqcells.com/Hotwire200.zip
Link is courtousy of TQ Steve.
#7589
Tech Master
The turbo delay lower than 0,5 is only use full on a small track. On larger tracks i prefer to use a higher turbo delay. It improves top speed acceleration and the motor temp stays lower.
On smaller tracks it's a good thing when you use a lower Boost.
Also do I think that the lower Turbo time is more for a 13,5 and so than for a 10,5T.
I want the Vegas version but I prefer the new version above this one.
Can't wait till it's there.
On smaller tracks it's a good thing when you use a lower Boost.
Also do I think that the lower Turbo time is more for a 13,5 and so than for a 10,5T.
I want the Vegas version but I prefer the new version above this one.
Can't wait till it's there.
#7590
Since I got my RS and Hotwire I have been messing around with my settings a lot and trying new things with it. I was curious what other people have been using as far as settings go with similar setups for 1/12 scale cars. I am running the Tekin RS v200 firmware, Fantom Ion2 17.5 (Trinity Duo 2 based) and SMC 50c 4900 single cell lipo. Any ESC setup, motor timing and rollout suggestions would be helpful. 80 ft x 48 ft track, medium to high traction.
Throttle profile 5
boost 18
turbo max
motor timing is 0
push at 70
rollout 96mm
delay .5