Brokin Racing

iTrader: (74)

Trevor, I'm sure any of the Hill mob would be glad to help out

Randy_Pike

iTrader: (6)

If you keep having 12 67 faults with a 1s car I'd like to know what steering servo you're using? Booster or Rx pack? And which one?

303slowdown

iTrader: (24)

ive had it happen with a jr 3650 with life receiver pack (protek 200mah)
and another with a futaba 9650 with a booster
and another with a jr 3650 with a 200mah lipo receiver pack wired in through the switch , and before anyone says anything about soldering it was soldiered very well and tried with different and new motors with new sensor wires.

hi-tech-redneck

iTrader: (1)

ok i haven't updated my speedo since v203,went to nor-cal raceway 2 weeks ago and found out i'm quite off the pace for 17.5 ramped tc,currently i have an lrp x12 17.5 in my photon with the stock timing piece (out of the box timing setting)but i have all of the timing inserts for the motor and i also have a new d3 in the box,anyone have a good setup starting point for such a track with eather of these motors.thanks guys!

M-Technic

iTrader: (15)

203 and 212 (and 208) are pretty much the same as far as power/speed goes.

Switch to your Duo3 and start with one of the setups from Tekin's site:

http://www.teamtekin.com/hotwire/ESCsetups/index.html

hi-tech-redneck

iTrader: (1)

yea already went the the ones on the site seems like there all setups for carpet atleast the 212 setups are!

wingracer

iTrader: (24)

For the LRP, go to the -10 insert, 40-45 boost, 10-15 turbo, 17k end, around 3-4k start, 5.7-6.0 FDR, ramp 2.

Randy_Pike

iTrader: (6)

Did both fail after a board tap incident?

303slowdown

iTrader: (24)

Only one was after a board tap , one was working fine did my hot laps before race ,stopped for start of race then wouldn't go , and the other worked fine then i turned off charged battery and wouldn't work after that, i tried reseting and then putting older software then new software still got the 12 67.

Randy_Pike

iTrader: (6)

Charge up your rx packs and watch their peak voltage. I'm curious to know if it's over 7 volts...

WEEZY

iTrader: (11)

Hey guys have a quick question, i was racing last weekend and took a hit and the car lost power. All the solder joints were together still and nothing was broke figured the switch just turned off. Well when i turned it back on it has steering and powers the transponder but there are no led's on the speedo. I tried to reset it with no luck? Any ideas, thanks in advance Ryan

smilekt

iTrader: (13)

for custom throttle profile C1 & C2 .. can use it on 212 ? how to setup ?

Randy_Pike

iTrader: (6)

http://www.teamtekin.com/hotwirehelp.html

smilekt

iTrader: (13)

Thanks Randy ..

from setup guide mention.. throttle profile for C1 & C2 cannot use yet

From User Guide
"Throttle Profile C1 and C2 are not in use as of yet, but they will be used for user programmable profiles in future software versions"

20 SMOKE

iTrader: (103)

led 1 is blinky
led 2 is preset* timing 5k-20k rpm
led 3 is preset* ll ll ll ll
led 4 ll ll ll ll ll ll
led 5
each preset is more timing
led 6 and 7 are you custom profile you pick timing and rpm range