Tekin RS ESC sensored
Tech Master
iTrader: (21)
Tech Adept
Set-up for 10.5t
Where can I get set-up for RS-Pro with X12 10.5t motor? I ll be using this combo in a Tc car (TCX). My local track has long straights with technical infield.
Thanks.
Thanks.
4 dot timing insert
Start RPM : around 6000
End RPM : around 21000
Boost : 45 to 48
Turbo : 10 to 12
Turbo Delay : 0.2
Turbo Ramp : 2
Min Drive : 10
Push Control : 0
Drag Brake : 5
FDR : 8.3 to 9.0
Tech Lord
iTrader: (32)
What's it mean if the ESC can't "see" the motor (the sensor LED's don't light) and the two LED's at each end of the bar flash?
Tech Master
iTrader: (8)
I had this same issue with my last ESC...I'm supposed to send it in. I can't remember the technical term used but it had something to do with the ESC losing a phase...or something like that. Since it does not see three phases the ESC thinks you have a brushed motor connected, hence the 1,2,6,7 (wrong motor type warning) lights flashing. (Tekin please correct me if I'm wrong )
Tech Lord
iTrader: (32)
I had this same issue with my last ESC...I'm supposed to send it in. I can't remember the technical term used but it had something to do with the ESC losing a phase...or something like that. Since it does not see three phases the ESC thinks you have a brushed motor connected, hence the 1,2,6,7 (wrong motor type warning) lights flashing. (Tekin please correct me if I'm wrong )
Tech Elite
iTrader: (5)
have you tried reflashing the esc? you might even try flashing with an older version then again with 212.
Led's 12 67 means the RS can't read a phase. This can be caused by the ABC motor wires, an open/shorted phase in the motor, or possibly something wrong internally with the esc.
Also on 1s there is one more possible cause. Insufficient BEC/Booster/Rx pack supply voltage.
Also on 1s there is one more possible cause. Insufficient BEC/Booster/Rx pack supply voltage.
Tech Adept
Tech Fanatic
iTrader: (37)
Tech Champion
iTrader: (34)
The silence on this subject is deafening.
Sounds like somebody let the cat out of the bag a wee bit early ?
Sounds like somebody let the cat out of the bag a wee bit early ?
Randy,
I have a Tekin RS which I plan to use on my 1/12th with a 1s lipo. Does the motor turn limit still apply or can I safely use a 4.0/4.5T since I assume the ESC will be pulling less amperes? Searched but very little info on this topic.
Lastly, I can't seem to find the wiring diagram for the RS with a booster/RX pack. Do I just remove the red wire in the ESC's plug?
Thanks in advance!
I have a Tekin RS which I plan to use on my 1/12th with a 1s lipo. Does the motor turn limit still apply or can I safely use a 4.0/4.5T since I assume the ESC will be pulling less amperes? Searched but very little info on this topic.
Lastly, I can't seem to find the wiring diagram for the RS with a booster/RX pack. Do I just remove the red wire in the ESC's plug?
Thanks in advance!
Tech Master
iTrader: (70)
Randy,
I have a Tekin RS which I plan to use on my 1/12th with a 1s lipo. Does the motor turn limit still apply or can I safely use a 4.0/4.5T since I assume the ESC will be pulling less amperes? Searched but very little info on this topic.
Lastly, I can't seem to find the wiring diagram for the RS with a booster/RX pack. Do I just remove the red wire in the ESC's plug?
Thanks in advance!
I have a Tekin RS which I plan to use on my 1/12th with a 1s lipo. Does the motor turn limit still apply or can I safely use a 4.0/4.5T since I assume the ESC will be pulling less amperes? Searched but very little info on this topic.
Lastly, I can't seem to find the wiring diagram for the RS with a booster/RX pack. Do I just remove the red wire in the ESC's plug?
Thanks in advance!