Tamiya mini cooper
#2341
Tech Elite
Originally Posted by AdrianM
Hi guys. I just wanted to let you know that Take Off just released RP40 compound mini tires. We now have the RP30, 36 and 40 compounds in the US. They are working on molded inserts and racing wheels for Mini Coopers right now. They will also have all tire compounds available as premounts once the inserts and wheels are done.
Adrian
Any RP24s in the works?
#2342
Tech Champion
iTrader: (261)
Originally Posted by Sydewynder
So you sold 2 GenX to get a mini copper?
If you're looking for rubber setup and I really can't help you cause I'm looking myself. If you're running foams and don't need TCs legal then I have some setups
If you're looking for rubber setup and I really can't help you cause I'm looking myself. If you're running foams and don't need TCs legal then I have some setups
Nah--I sold two GenX's because I really didn't like them once I got one of them built. Several reasons, but I was sure glad I hadn't sold my two $400 brand new 3.2R's!!
I don't need TCS-legal as it'll just be for fooling around between rounds, etc but I DO want to stay with the rubber tires (less maintenance, longer life).
Any setups appreciated.
Scottrik
#2343
Tech Elite
Originally Posted by Customworksking
dude I won the Novak with just lowering the car via what ever camber gain it had nothing else bottom line U need to drive point blanK
#2344
Originally Posted by DrKucho
you have not much options, i think cutting the adjusters is the only way to go , use glue once you screw it to aviod from pop off
#2345
Originally Posted by Customworksking
what u can do is cut the link in 1/2 thread a ti rod in each side say a corally rod and see if that will work
#2346
Tech Elite
Originally Posted by Scottrik
Nah--I sold two GenX's because I really didn't like them once I got one of them built. Several reasons, but I was sure glad I hadn't sold my two $400 brand new 3.2R's!!
I don't need TCS-legal as it'll just be for fooling around between rounds, etc but I DO want to stay with the rubber tires (less maintenance, longer life).
Any setups appreciated.
Scottrik
I don't need TCS-legal as it'll just be for fooling around between rounds, etc but I DO want to stay with the rubber tires (less maintenance, longer life).
Any setups appreciated.
Scottrik
Any setups appreciated.
Scottrik[/QUOTE]
My set up with foams on Ozite carpet (car on the ground weighted with everything):
Yokomo SSS shocks
Tamiya short blue springs front*
Tamiya short Yellow springs rear*
50 wt shock oil all around
Silver (hard) swaybars front and rear
2 degree rear toe uprights
About 1/2 degree front toe out. (it will toe-in on compression)
Stock upper link for front camber
TL01 upper link for rear camber (see my other post about this)
TRC Plaid front foam trued 58mm, CA sidewall (60mm will work about the same)
TRC Purple rear foam trued 58mm, CA sidewall (60mm will work about the same)
Tamiya stronger servo saver w/metal ring
Tamiya Manta Ray ball diff tight as possible still with diff action
Raise the shock collars all the way up to get car as low as possible. Chassis is ~ 4mm at the lowest point near the front
ESC and receiver placed in the opening near the rear of the chassis. (Low as Possible)
Bearings all around
If running on smooth surface:
I have not done this yet but put in o-rings or fuel tubing in the shock as you built it to reduce or remove the droop. This will reduce weight transfer to the rear and front wheelspin on-power.
3200 Lipos work but Nimh work better because it weighs more.
*Springs are individually packaged. The ones that are packaged as a set of blues, yellows and reds are longer than the ones I'm using even though they say they are short springs.
#2347
Originally Posted by Sydewynder
I agree that if you lower as much as you can you should get as much camber gain as needed.
On another note. Is there a really good brand of bearings u folks use on the M03/M. ceramic vs. steel? any thoughts?
#2349
on asphalt i run mine 4mm in the front 6mm in the rear, but my rear springs are soft and with lots of droop. remember, when a fwd car turns a corner quickly, it has a tendency to 3 wheel, like a dog peeing
#2351
that thing is low! How much droop you set on that beast?
#2354
Originally Posted by Customworksking
this is how i will run at the novak race
I'm using the super mini cva and just cant get it past parallel unless u start trimming off the piston rod.