Yokomo 1/12 MR4-TC Mini
#166
Re: Hmm
Originally posted by dynamic_e
I was on my way to cut out a chassis when i realized that not just the chassis is shorter, but so are the arms...and joint...hmmm..
Back to square one. Can anyone confirm what parts are interchangeble between the full size and the mini?
I was on my way to cut out a chassis when i realized that not just the chassis is shorter, but so are the arms...and joint...hmmm..
Back to square one. Can anyone confirm what parts are interchangeble between the full size and the mini?
2. shocks
3. bulk heads
4. diffs
5. drive spur
6. bumpers
7. front and rear uprights
8. c-hubs
9. servo saver (parts only... instalation is different)
#167
everything is the same except dogbones , upper/lower arms & chassis.
i have recently fitted my yok mini with 10th scale yok arms, handling is so much better, and i use a 1/10 mini cooper bodyshell, it's basically a shorter length 1/10 scale car powered by 4 cells,
try it without the belt, rwd is so much fun
i have recently fitted my yok mini with 10th scale yok arms, handling is so much better, and i use a 1/10 mini cooper bodyshell, it's basically a shorter length 1/10 scale car powered by 4 cells,
try it without the belt, rwd is so much fun
#168
I can't wait for other companies to come out with 1/12 tourers!
#170
Originally posted by rcracingfreak
like Xray....hint hint
like Xray....hint hint
#171
3 new mini's at connecticut speedway:
#172
a closer view:
#173
mini me:
#174
top view of mini me... :
#175
question for helpwanted
hello helpwanted that mini yoke looks awsome
i was planning on getting one with the brushless novak
system , what kind of runtimes are you getting out of
the set up , are you using 3000mah or what , and
about how fast guesstimate on speed.
any info is greatly appreciated thankyou
sb
i was planning on getting one with the brushless novak
system , what kind of runtimes are you getting out of
the set up , are you using 3000mah or what , and
about how fast guesstimate on speed.
any info is greatly appreciated thankyou
sb
#176
Tech Fanatic
A friend of mine at my track just got his, and with a stock motor, I don't mean to critisize them or anything, but theyre slow. But if you built up a 6 cell pack just like some nitro car reciever packs, and put a couple slots in the chassis to tape the pack in, that thing would be a rocket ! Not sure if enough people at my track will get them for it to become a class though.
#177
Re: question for helpwanted
Originally posted by sbmon
hello helpwanted that mini yoke looks awsome
i was planning on getting one with the brushless novak
system , what kind of runtimes are you getting out of
the set up , are you using 3000mah or what , and
about how fast guesstimate on speed.
any info is greatly appreciated thankyou
sb
hello helpwanted that mini yoke looks awsome
i was planning on getting one with the brushless novak
system , what kind of runtimes are you getting out of
the set up , are you using 3000mah or what , and
about how fast guesstimate on speed.
any info is greatly appreciated thankyou
sb
but when we hit the 1/10 tracks we use very hot motors like 9x2, 8x2. and it kicks the @ss of 19 turn motors. we ran it up against 1/10 cars with mod motors and for the first 2 mins it has no problem keeping up. after that the car is still awesome but you will notice that the topend speed is less. but it still is hella fast. on a good charge you could last about 6-7 minutes before it suddenly crawls.
#178
Tech Fanatic
I think mod motors are the way to go with these cars !
#179
Tech Elite
iTrader: (2)
i am running yoko 8x2 mod motor on mine !! with 4cell GP3000, it gives a bit more than 6 min run time. however, i also noticed that the servo action is not as smooth in the last 3 mins before the batt dump .... i am now using a 6v FET servo (KO 2004FET), i might switch to a normal 6v servo (Futaba 3003) to see if this will improve.
ps : i already install a 1000uF cap on the rx bec.
ps : i already install a 1000uF cap on the rx bec.
#180
Tech Elite
iTrader: (7)
Join Date: Jun 2002
Location: Melbourne, Australia. Home of rc-mini.net
Posts: 3,549
Trader Rating: 7 (100%+)
Sick of the Stratus?
I dont know if any of you guys have seen these, but this is one of the Northcraft bodyshells for the Tamiya Mini. As it happens, it also fits the MR4TC-Mini even better!
And how cute does a baby cartoon Subaru WRX look?
And how cute does a baby cartoon Subaru WRX look?