rx7ttlm

iTrader: (30)

there is a Paul bobble head?! lol.. is this distributed by trinity? lol

RKeasler

iTrader: (5)

Paul got a question for you. I may get to the track before you answer, but here goes. If I put my front arms all the way forward and my rear arms all the way forward what is my likely result handling-wise?

Rod

The Teacher

iTrader: (62)

Paul, if my car spins out to the right on left hand turns should I run a spool up front with my one-way low in the rear to get less roll...

ABM

c1 racin

iTrader: (8)

Paul,
Have you tried the new T2'009 Rubber-spec Conversion Set .... pro's and con's .... of the forward motor position.

bigdadracing

iTrader: (1)

paul,
just wanted to personally invite you to the 2009 xray challenge this year as well as everyone else !! so paul bring your car this year so you can woop on us were looking to do this july 17 thru 19th here in portland, or .the club and myself are looking forward to hopefully seeing everyone this year for the event .we should have a link up for the race on the nw racer forum soon ...

adamge

iTrader: (1)

Paul, for setup:
http://forum.teamxray.com/xform/inde...1&setup=t2_008
Can you confirm what rear hub shims you used? Was it really 0mm?
-Adam

Paul L

Yea i think its pretty funny too, cant wait to get it.

99% sure that you will get mega steering, and not much forward stability. sorry i didnt get to you earlier. so am i right, or do i suck. LOL

I think that you need a left front spool with a right front one way. LOL.
Hi, The forward motor position should excell in lower bite situations, it should be easier to drive but have a bit less steering.
Thanks

Thanks for looking out!, i will for sure talk to ralph about it. hope to see you their.


Thanks for posting that, If thats my foam set-up, I definately do not use 0mms on my foam car ever, i think that i had 4mms on the hub at that race. My fault on that one, i will have to get on their and change that.

ToysRUsKid

iTrader: (16)

Hi Paul, just wondering if you'll be at the Capital Classic at 301 raceway this year? If so, can I stop by your table and steal some NT1 secrets from you?

rx7ttlm

iTrader: (30)

hey paul, using your novak setup for rubber tires, the car seems to be loose off power and understeers on power, you have a quick fix for that?

STLNLST

iTrader: (32)

Paul-I had to revamp BN RACING due to the economy so if you still want to be part of the team I'll need you to fill out a sponsorship application again. I have a spot reserved for you though. Just let me know

Paul L

I will be their! please do, Thanks

Lately i have had a similar problem with that set up and have heared the same thing from others who are running it. so maybe the set up is not as good for all tracks as i originally thought, maybe try running 4deg caster blocks in place of the 6's and shortining thr rear wheelbase. that is what i would try first. Thanks


Thanks C, we will have to do a formal interview at the reedy race to secure my position on the team. darn recession, screwing up the team! lol

cabinetgod

hey paul how's the fishing been since clevland

Kropy

iTrader: (12)

Paul ~ What up homie

mickrcarver

iTrader: (101)

Paul,do you have a sister?

rosko

i have a 009 us with a 104 spur and trinity brushless motor is it possible to get the rollout that one would run with a 17.5, or do i need a smaller spur. i saw ea running a 100 tooth spur on his 09 nats setup sheet. foam tire