Tamiya TRF416 / TRF416WE / TRF416X

You're on Page 112 of 708
Go to
  • Just installed the 3racing 4degree front uprights, seems to be good quality and fit. Just wanted to let you know if you order these, you should also order .3mm shims if you don't already have them, as there is a lot of up and down play between the steering hub and the upright bushings without them.
  • I just tried a pack of Venom 5000 Lipos and they just fit under the upper deck. To my surprise they are a lot punchier than the MaxAmps 5000s I already had.
  • some good pixs ...

    http://www.flickr.com/photos/[email protected]/
  • For the spool is the following all I need?

    1x TAM3454401 Direct Holder
    1x TAM9804268 Delrin Drive Cup
    1x TAM9804267 Alloy drive sleeve
    1x TAM54023 37t One way pulley
    1x TAM51278 K Parts

    Are the pins included in the above parts?
  • Quote: wait more 1-2 month !
    Any more information?
  • Quote: For the spool is the following all I need?

    1x TAM3454401 Direct Holder
    1x TAM9804268 Delrin Drive Cup
    1x TAM9804267 Alloy drive sleeve
    1x TAM54023 37t One way pulley
    1x TAM51278 K Parts

    Are the pins included in the above parts?
    Good point... I don't think they are. You'll need 2 x 2x9.8mm pins (TAM52500) for pining the drive cups... better add that onto the list!

    Cheers
    Ed
  • may have already been posted and noted, but square branded 416 c hubs and arms here... (scroll down)

    http://www.redrc.net/page/2/
  • Quote: Please post when the hubs are available - thanks
    Today Square C hub & front upright was back in stock !
  • Quote: Any more information?
    TRF416 Spool APR release
  • Quote: TRF416 Spool APR release

    Very cool!!......... Thanks
  • Well thank F for that....

    Stripped my car apart this evening, first attempt I've had at looking into what the issue was from the weekend. Turns out it was simply a badly bent left rear hinge pin. Not sure when I would have bent that, but I'm guessing it would have been during the last meeting, although don't recall hitting anything hard enough to bend it. Do remember hitting the wall at the last Carpet wars round, and I didn't check the car between thoose runs... so that possibly where the issue started.
    Still, given me a good excuse to strip the car and give it a fettle, even re-built the diff (although it didn't need it, even after 50+ runs ), only thing I didn't rebuild were the shocks, but I'll proably do that some point this week.
    Hopefully I'll get a run next weekend, otherwise it's going to be a few months before I get the next opportunity to do so, as my other hobby kicks off it's season soon. Hey ho, have to see what happens.

    Cheers
    Ed
  • On the DHI setup that Jilles posted, does anybody know what those downstop settings (6mm up front, 5 in the rear) would be if measured as uptravel, or droop over ride height.

    http://www.petitrc.com/reglages/tami...2008011113.htm
  • Hi,

    downstop (droop) is measured at the end point (near the outer 2.6mm suspension shaft) of the suspension arm.

    The Square Knuckles are still in stock (STV-35MS). The C-Hubs will arrive around Thursday (28.04.). I will bring them to the LRP-Touring Car Masters in Eppelheim.
  • the Much More backed European Touring Series,

    anyone seen the tamiya setups for the 1st three tamiys
  • I looking to buy the front diff from Tamiya. http://www.tamiyausa.com/product/ite...oduct-id=53921

    What gear do I need to go with it? Part number if you know it.

    I know this is the 416 thread but I need to get this ordered.

Similar Threads