2LikesGM Brushless
10-09-2009, 12:05 PM
#1036
Tech Fanatic
iTrader: (1)
Hi
I am having a issue with setting up my GM120, I can send the data to the speedo but when i receive the data it hasn't saved it and just shows up the factory settings. Matt W has tried to fix it but has had no luck with it (Very appreciated for trying to fix it tho Matt
) Does any else have any other ideas that could solve the problem?
Regards
Jordan
I am having a issue with setting up my GM120, I can send the data to the speedo but when i receive the data it hasn't saved it and just shows up the factory settings. Matt W has tried to fix it but has had no luck with it (Very appreciated for trying to fix it tho Matt
) Does any else have any other ideas that could solve the problem?Regards
Jordan
Try connect batt first and download data
m.
10-09-2009, 12:22 PM
#1037
Suspended
10-09-2009, 12:36 PM
#1038
Tech Master
In fact I have seen when battery is connected, it won't transfer data at all. Jordan, that was a proper odd issue, neither me, CK or CG had any ideas - one for Martin me thinks.
10-09-2009, 12:41 PM
#1039
Suspended
If its off, it will not power the ESC.
10-09-2009, 01:06 PM
#1042
Suspended
Could be that if the USB can not provide enough energy, you need to connect the bat. We never had this problem and read and write without bat.
10-09-2009, 02:40 PM
#1043
Tech Master
My point was that everything works when you don't connect a pack/cells, but, if you have pack/cells connected then I have seen it fail - although mine seems fine with this!!
That isn't connected to the issue that Jordan asked about though.
That isn't connected to the issue that Jordan asked about though.
10-09-2009, 04:33 PM
#1044
have you updated your pc software/ usb driver recently?
it's absolutely necessary to keep it up to date
check your sensorport on the speedo if there is a pin bent! (you need to have a really close look :-) )
the battery should not be connected to the speedo at all when setting up the speedo!
the ubs powers the speedo and nothing else...
for lipo modified just use regular mode 2/3 sensorless with factory settings
it's absolutely necessary to keep it up to date
check your sensorport on the speedo if there is a pin bent! (you need to have a really close look :-) )
the battery should not be connected to the speedo at all when setting up the speedo!
the ubs powers the speedo and nothing else...
for lipo modified just use regular mode 2/3 sensorless with factory settings
10-10-2009, 03:34 AM
#1045
And donīt forget to switch off the speedo if the switch is on it will not work
10-10-2009, 04:10 AM
#1046
Tech Regular
Hi
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
10-10-2009, 05:33 AM
#1047
Suspended
Hi
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
(12th scale)We will do some tests this evening and will let you all know what to do.
10-10-2009, 05:52 AM
#1048
Tech Regular
Thanks
10-10-2009, 09:06 AM
#1049
Tech Initiate
Hi
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
I have got a 120 with 4.9 firmware for my 12th i set it up like i want but the brakes seem to be ethier grabbing or none at all any one got a set up for the brakes.
Also on the other esc i have had all i had to do was turn down the atl on my handset but on this one it makes the car roll forward instead it this a fault someware ?
Thanks
well not very well anyway.
10-10-2009, 02:44 PM
#1050
Brake issues are 99% of times Tx setup issues. Please make sure your transmitter values (advanced settings) are as close to 1,9/1,4/1,1 (fullthrottle/neutral/full brake) as possible!
If they are not you are doing the tx setup/mode picking process the wrong way
If they are not you are doing the tx setup/mode picking process the wrong way