ESC forum
11-19-2001, 10:55 AM
#391
Originally posted by TCRboy
do the Quantums have replaceable wires? and a good spec or not, when compared to the prices of the IPC range?
do the Quantums have replaceable wires? and a good spec or not, when compared to the prices of the IPC range?
11-19-2001, 12:46 PM
#392
Tech Initiate
thanx m8
isn't the nosram dominator series made by lrp? what's the dominator (not the dominator power, i'm talking about the model below) like? i'll be running it in a yok mr4 TCR with a 19d (control motor)
cheers
isn't the nosram dominator series made by lrp? what's the dominator (not the dominator power, i'm talking about the model below) like? i'll be running it in a yok mr4 TCR with a 19d (control motor)
cheers
11-19-2001, 05:17 PM
#393
When I said RCCA uhh.. I meant RC Car Action magazine website. So just go to rccaration.com and click on RC Zone, then Bulletin boards. Then go to uhhh Electronics. You could do a search for uhh like I said before 
I'll even bump the post up so you can see it if you go on tonight......
Jimmy Mac
I'll even bump the post up so you can see it if you go on tonight......Jimmy Mac
11-19-2001, 08:01 PM
#394
Thanks Kill Ruf i thought u said Radio Control Car Assiosation as in RCCA lol i looked everywhere for it b4 commin back to post 
ok will check it now
TY
ok will check it now
TY
11-19-2001, 08:47 PM
#395
Originally posted by TCRboy
thanx m8
isn't the nosram dominator series made by lrp? what's the dominator (not the dominator power, i'm talking about the model below) like? i'll be running it in a yok mr4 TCR with a 19d (control motor)
cheers
thanx m8
isn't the nosram dominator series made by lrp? what's the dominator (not the dominator power, i'm talking about the model below) like? i'll be running it in a yok mr4 TCR with a 19d (control motor)
cheers
11-19-2001, 09:54 PM
#398
what the operating frequencies are for ?
there are two choices on my v12, 2 & 4khz.
also, i need some input from gmv12 users concerning the setup values for my guidance. as of now, i set it up as follows:
#1 turbo (3)
#2 min brk (5)
#3 max brk (3)
#4 (factory setting)
i happen to use the 3PJ, when i set up my v12 with above values, i can't adjust the brake from the radio (ATL).
does this mean, i can only adjust the brake from esc ?
there are two choices on my v12, 2 & 4khz.
also, i need some input from gmv12 users concerning the setup values for my guidance. as of now, i set it up as follows:
#1 turbo (3)
#2 min brk (5)
#3 max brk (3)
#4 (factory setting)
i happen to use the 3PJ, when i set up my v12 with above values, i can't adjust the brake from the radio (ATL).
does this mean, i can only adjust the brake from esc ?
11-19-2001, 10:01 PM
#399
Originally posted by redsand
what the operating frequencies are for ?
there are two choices on my v12, 2 & 4khz.
also, i need some input from gmv12 users concerning the setup values for my guidance. as of now, i set it up as follows:
#1 turbo (3)
#2 min brk (5)
#3 max brk (3)
#4 (factory setting)
i happen to use the 3PJ, when i set up my v12 with above values, i can't adjust the brake from the radio (ATL).
does this mean, i can only adjust the brake from esc ?
what the operating frequencies are for ?
there are two choices on my v12, 2 & 4khz.
also, i need some input from gmv12 users concerning the setup values for my guidance. as of now, i set it up as follows:
#1 turbo (3)
#2 min brk (5)
#3 max brk (3)
#4 (factory setting)
i happen to use the 3PJ, when i set up my v12 with above values, i can't adjust the brake from the radio (ATL).
does this mean, i can only adjust the brake from esc ?
Lower frequency = more punch
higher frequency = smoother response
Everyone has different preferences for the profiles. Just whatever you are comfortable with!
When calibrating your V12 make sure you have the ATL set to 100 otherwise the V12 may not recognise the brake input from the TX. Turn the ATL down after you have setup to reduce the braking.
11-20-2001, 01:38 AM
#400
Originally posted by dtm
When calibrating your V12 make sure you have the ATL set to 100 otherwise the V12 may not recognise the brake input from the TX. Turn the ATL down after you have setup to reduce the braking.
When calibrating your V12 make sure you have the ATL set to 100 otherwise the V12 may not recognise the brake input from the TX. Turn the ATL down after you have setup to reduce the braking.
I have turned down the ATL value from 100% to 80%, the brake still seems a bit strong. Turning down more than 80, the esc starts to make a beeping noise with the red LED flashing.
Now what's up with that ?
11-20-2001, 06:33 AM
#401
Redsand: I'm going from memory here but try this test;
1. Plug a servo into the ESC channel of your reciever (put a servo horn on to make the servo movement more obvious).
2. Adjust the ATL (-ve) without touching the throttle trigger and see if the neutral position shifts.
3. Apply a tiny bit of forward throttle and see if the servo moves a 'tiny' bit off the neutral or whether it 'jerks' forward to a position.
Get back with the results!
You are running a 3PJ and not a 3PJS right?
1. Plug a servo into the ESC channel of your reciever (put a servo horn on to make the servo movement more obvious).
2. Adjust the ATL (-ve) without touching the throttle trigger and see if the neutral position shifts.
3. Apply a tiny bit of forward throttle and see if the servo moves a 'tiny' bit off the neutral or whether it 'jerks' forward to a position.
Get back with the results!
You are running a 3PJ and not a 3PJS right?
11-21-2001, 01:14 PM
#402
Tech Initiate
what difference does the amp rating on an ESC make to the performance of the car??
11-21-2001, 07:50 PM
#403
more amp rating = more punch expecially when coming outa coners .... and in that way u accelerate faster
guys i need some help ...
i m gona get a GMv12xc soon real soon ...waiting 4 shipment ... the guy said not so soon
for now .. my curent ESC has got some big problem!!!
when i m comming out of the turn i punch the trottle but the car does not semed to accelerate untill i let off my stearing to neutral position b4 the car starts accelerating.
now thats LOTS of SECs lost there. still cannot figure out whats wrong except the ESC has its timer ticking close to the end of its life time.
guys i need some help ...
i m gona get a GMv12xc soon real soon ...waiting 4 shipment ... the guy said not so soon
for now .. my curent ESC has got some big problem!!!
when i m comming out of the turn i punch the trottle but the car does not semed to accelerate untill i let off my stearing to neutral position b4 the car starts accelerating.
now thats LOTS of SECs lost there. still cannot figure out whats wrong except the ESC has its timer ticking close to the end of its life time.
11-21-2001, 08:18 PM
#404
Originally posted by imataquito
for now .. my curent ESC has got some big problem!!!
when i m comming out of the turn i punch the trottle but the car does not semed to accelerate untill i let off my stearing to neutral position b4 the car starts accelerating.
for now .. my curent ESC has got some big problem!!!
when i m comming out of the turn i punch the trottle but the car does not semed to accelerate untill i let off my stearing to neutral position b4 the car starts accelerating.