Xray T2'007
03-28-2007, 11:13 AM
#2191
Originally Posted by Itchy
An Xray chassis with a filled rectangle for the lipo battery (the same way it is beneath the motor) would also be interesting
Thank you nexus
. I actually tried that on the std T2...I set up my drill press to mill an old chassis down about 1.5mm to fit the Platinum 4800. It actually worked OK, but NiMH would no longer fit in that chassis.
03-28-2007, 11:19 AM
#2192
Originally Posted by Mr. Shookie
Great info on the 4800 lipo Arun, I might have to look into one of those..LOL
But I think he asked about the 3200 Race Spec Lipo.
He will only need to use a dremel on the right side spur gear bulkhead, takes all of 15 minute.
Just remove a little at a time until you have about 1.5-2.0mm clearance.
If fits perfect and sits really low.
When I get time later I will try to snap off a couple of pics.
Hope that helps,
-Shookie <><
But I think he asked about the 3200 Race Spec Lipo.
He will only need to use a dremel on the right side spur gear bulkhead, takes all of 15 minute.
Just remove a little at a time until you have about 1.5-2.0mm clearance.
If fits perfect and sits really low.
When I get time later I will try to snap off a couple of pics.
Hope that helps,
-Shookie <><
. We have just been cutting the case of the carbon battery to clear the bulkhead in the EU like described on Xray's forum. Haven't tried cutting the bulkhead...I guess it is a choice of hurting the resale value of the car or the battery, lol.
03-28-2007, 12:04 PM
#2193
Originally Posted by Nexus Racing
Read a little closer . We have just been cutting the case of the carbon battery to clear the bulkhead in the EU like described on Xray's forum. Haven't tried cutting the bulkhead...I guess it is a choice of hurting the resale value of the car or the battery, lol.
. We have just been cutting the case of the carbon battery to clear the bulkhead in the EU like described on Xray's forum. Haven't tried cutting the bulkhead...I guess it is a choice of hurting the resale value of the car or the battery, lol.Yea but the bulk head is only $14.00 which I have a stock one as a spare...LOL
https://www.ssl-stormerhobbies.com/c...s&pn=XRA303019
And the Orion pack is how much...?
Just messing bro...
I just don't trust myself to mill out the case...
knowing me like a do...I would trim too much and poof...LOLYou just have to flatten out where the bulkhead curves to make it fit...
-Shookie <><
03-28-2007, 04:09 PM
#2194
Originally Posted by Nexus Racing
. I actually tried that on the std T2...I set up my drill press to mill an old chassis down about 1.5mm to fit the Platinum 4800. It actually worked OK, but NiMH would no longer fit in that chassis. (but know that i think on it, it makes sense)In the long run, if/when lipo is regulated and the mainstream powersource, i believe the "milled rectangle" is the better solution. Not only it lowers the CG a litle, but it helps to secure the battery a lot beter.
Right now it might be dificult though, since nobody knows what the standard size should be...
03-30-2007, 10:25 PM
#2195
03-30-2007, 11:50 PM
#2196
How to stay your Brushless ESC & Receiver in T2'007 ?
have photo ?
have photo ?
03-31-2007, 03:20 AM
#2197
Here's some Photo's of mine with a Brushless setup and Spektrum Pro Receiver. All wires where shortened to make it neat & tidy.
Hope these help.
Hope these help.
Originally Posted by RC MARKET
How to stay your Brushless ESC & Receiver in T2'007 ?
have photo ?
have photo ?
Last edited by DTM.inc; 10-07-2007 at 05:16 AM.
03-31-2007, 04:07 AM
#2198
Originally Posted by DTM.inc
Here's some Photo's of mine with a Brushless setup and Spektrum Pro Receiver. All wires where shortened to make it neat & tidy.
Hope these help.
Hope these help.
why don't move cap in under upper deck ?
03-31-2007, 05:19 AM
#2201
Originally Posted by HarshGuy
Here's mine, with a speedpassion cap.
03-31-2007, 05:51 AM
#2203
Gravity RC
I always put my Speed passion cap on top of my reciever and the reciever is on its side. someday i will get smart and be able to post a pic of the layout.
03-31-2007, 07:33 AM
#2204
PAULLLLEMIEUUUUUUUUUUUX!!!!
Whatup brother?
Lasso any tumbleweeds lately?
Call me sometime!
Whatup brother?
Lasso any tumbleweeds lately?
Call me sometime!
03-31-2007, 07:37 AM
#2205
Originally Posted by c1 racin
Have mine the same way in my '007 EU and '007 US....also a pic of the '007 EU with a 3200 LiPo pack
after i'm post my New 007 photo
& have other good stay low CG all receiver & ESC with short cable ?.