New X10P4 Touring Car From MLP
#256
Hey guys! Keep the suggestions and ideas coming, we are always open to industry input. MLP R/C Motorsports INT is one of the only companies that will show you guys our development process and prototypes as we go through the process, no "spy pics" and innaccurate information.
Start placing your pre-orders, because this car is sweet!
Start placing your pre-orders, because this car is sweet!
#259
The official testing of the MLP R/C Motorsports INT X10P4 touring car will begin this week. I will post track locations and times where I will demo the car and also race the car in the Southern California area. I will also be racing the MLP F201 SCF-PRO at some of these times. If anyone has specific locations they would like me to bring the cars to, and are interested in seeing them, please do not hesitate to email me. Place your orders now, this car is awesome!
#260
Thanks for the compliments, Jason. It's good to see an open mind and a positive attitude.
#261
Mid Motor setup
Here is a look at the mid motor setup - with this configuration you can run 6 cells side by side or saddle pack 3X3 and 4x2 and I will post pictures of each today
Thanks for checking us out and to see how the build is going.
stop by again!
Thanks for checking us out and to see how the build is going.
stop by again!
Last edited by Marty Peterson; 08-03-2008 at 12:48 PM.
#264
Marty, You have got to be the busiest person on the planet right now. Looks like you have really gotten everyones attention! Show'em what the cars can do and take no prisoners! I'll do my part along with the team drivers, which you should start calling the Star Trek team. " Kicking butt where butt has never been kicked before!". It's the little things that make the difference. All they have to do is see the car and take it for a lap to know. Nuff'said! See Ya!
#265
Tech Master
iTrader: (2)
Originally Posted by Marty Peterson
So now the MLP X10P4 has a rear motor setup as in the pictures before and with the same car it can turn into a mid motor setup and Multiple Battery setups!
3X3 Mid motor!
3X3 Mid motor!
#266
Originally Posted by RandyB
thats what im talking bout! however it will be very hard to wire electronics unless you can move the servo over to the other side.
And the Mid motor and 4X2 battery set up!
There are holes to move it to the other side! Just I have been up all night finishing this thing and I do not want to turn another Screw !! Plus when testing is done we have a cool way to keep all the wiring in place! and looking good.
Last edited by Marty Peterson; 08-03-2008 at 12:48 PM.
#267
Marty,
the car looks mighty fine, I love the 4x2 to even the balance. when we ran 2400s inline 6 was just about ballanced, but now with the new jumbo batters this appears to be a logical solution.
Marty you are forcing me to go back to on road touring and f1 again!!
wn
the car looks mighty fine, I love the 4x2 to even the balance. when we ran 2400s inline 6 was just about ballanced, but now with the new jumbo batters this appears to be a logical solution.
Marty you are forcing me to go back to on road touring and f1 again!!
wn
#268
Thanks nagatahawk Yep and with the New Lipo cells out there what is next
We are just looking to make a car that will come with all the hopups and that can change from one setup to another.
I feel we did it!
Do you want to see the parts you need to put the motor back in the rear?
Like this.
We are just looking to make a car that will come with all the hopups and that can change from one setup to another.
I feel we did it!
Do you want to see the parts you need to put the motor back in the rear?
Like this.
Last edited by Marty Peterson; 08-03-2008 at 12:48 PM.
#269
The Parts needed to take it back to rear motor and 6cell side by side!
Yep two upper plates and a set of servo posts! Thats it!
more info later
And Remember you can also see us at www.mlpmotorsports.net
and here at r/ctech @ http://www.rctech.net/forum/showthread.php?t=115568
Yep two upper plates and a set of servo posts! Thats it!
more info later
And Remember you can also see us at www.mlpmotorsports.net
and here at r/ctech @ http://www.rctech.net/forum/showthread.php?t=115568
Last edited by Marty Peterson; 08-03-2008 at 12:48 PM.
#270
Tech Adept
This thing is going to be awsome... remember its only a prototype ... imagin how good the production version is going to be !!
-Hugo
-Hugo