143LikesTamiya TB Evolution V
05-11-2006, 02:36 PM
#106
Tech Regular
That's the MSRP, store price will be much much lower.
05-12-2006, 01:08 AM
#108
Shop Owner
For special price go to this link http://www.rctech.net/forum/showthread.php?t=113703
Had just uploaded some pictures in the same link.
Had just uploaded some pictures in the same link.
Last edited by Masa; 05-12-2006 at 02:52 AM.
05-12-2006, 03:02 PM
#109
Thats a bit more like it, must admit to being quite tempted 
On another note, the Evo 4 MS suspension mounting blocks need 1mm shims, which I think is a pretty naff idea tbh, whereas the Evo 4 blocks dont, much stronger and less prone to bending and tweek. Does anyone know if the standard Evo 4 blocks work okay on the MS? or, know anywhere that sells full width shims?
On another note, the Evo 4 MS suspension mounting blocks need 1mm shims, which I think is a pretty naff idea tbh, whereas the Evo 4 blocks dont, much stronger and less prone to bending and tweek. Does anyone know if the standard Evo 4 blocks work okay on the MS? or, know anywhere that sells full width shims?
05-13-2006, 10:47 AM
#111
Originally Posted by TryHard
Evo4 blocks will work fine 
I use them myself on my 415 when I want to raise the roll centre on my 415 using the suspension blocks.
Ed
I use them myself on my 415 when I want to raise the roll centre on my 415 using the suspension blocks.Ed
05-13-2006, 11:59 AM
#112
Tech Adept
Dont know whether the evo V batt holder k be use on evo IV anot it look much nicer
05-13-2006, 02:17 PM
#114
Tech Elite
Join Date: Mar 2004
Location: MOOD;; feeling good not racing ,saving shed loads of money,lovely Tan i have aswell
Posts: 4,762
Edd & terry
look at this for the Hybrid stuff from CML in UK
got shims for the evo4/415
you have to go to olly jefferies link for the BTCC round
but they do 1 piece shims to raise & lower the roll centre
might get one , then again might not
look at this for the Hybrid stuff from CML in UK
got shims for the evo4/415
you have to go to olly jefferies link for the BTCC round
but they do 1 piece shims to raise & lower the roll centre
might get one , then again might not
05-13-2006, 02:30 PM
#115
Originally Posted by terryh
Thanks for that Ed, will order some this weekend then so that I can use them on my new MS
05-13-2006, 03:14 PM
#116
Thanks Jolly, can always trust you to point us in the right direction 
05-13-2006, 03:16 PM
#117
Originally Posted by i.a.s
I have your new MS in my living room
You make sure you look after it mate, oh, and a bit of advise, DONT OPEN THE BOX, you might not be able to resist wanting it and I cant have that 
05-13-2006, 03:44 PM
#118
Originally Posted by MR JOLLY
Edd & terry
look at this for the Hybrid stuff from CML in UK
got shims for the evo4/415
you have to go to olly jefferies link for the BTCC round
but they do 1 piece shims to raise & lower the roll centre
might get one , then again might not
look at this for the Hybrid stuff from CML in UK
got shims for the evo4/415
you have to go to olly jefferies link for the BTCC round
but they do 1 piece shims to raise & lower the roll centre
might get one , then again might not
Gonna make it my indoor car, not bad for about £180 on the Champ pre-order
05-13-2006, 06:34 PM
#119
Tech Master
curious, most ppl want to make the evo V an indoor racer... just wondering... what makes this car more suitable for indoor than out door? I was looking at the specs on the tamiya website and it says it has a minimum clearance of 5mm... isn't that a bit high for minimum clearance?
05-13-2006, 07:01 PM
#120
Slightly changing the topic on this thread, does anyone know an estimate release or a possibility of a conversion kit from evo iv to evo v?