Team Associated TC5
#2717
Tech Rookie
!3.5 Setup
I have a few questions.
1. What is the best gearing for a 13.5BL on a short tight track (asphault)?
2. The best servo?
3. And of course a base setup for rubber carpet and asphault?
Dennis
1. What is the best gearing for a 13.5BL on a short tight track (asphault)?
2. The best servo?
3. And of course a base setup for rubber carpet and asphault?
Dennis
#2719
Tech Initiate
Ran the new car for the first time Saturday, my trusty old TC3 is retired! So smooth and easy to drive, if the ITF chassis set makes it much better.... just set the cruise control and ride. LOL
#2720
Tech Regular
You can find both setups on rc10.com.
All the major radio mfgs. make a good servo. I recomend the kopropo low profile #2413
I haven't run a 13.5, sorry I can't help you on that one.
Walter
All the major radio mfgs. make a good servo. I recomend the kopropo low profile #2413
I haven't run a 13.5, sorry I can't help you on that one.
Walter
#2721
I ran on saturday and loved the car. I ran Ryan Cavalieri's Reedy Race setup. I needed to add the orings to the top but didnt have time to add them. The rear end was loose. The car had more steering then any car I have run before. I think as soon as I can get the ITF chassis on it the car will be dialed. I was turning close to the same times as the guys running 19t.
Great Car!
Corey
#2722
Tech Elite
iTrader: (101)
Reedy Setups
Hello Brent (51),
I was looking at Ryan and Kyle's setup's from the Reedy Race and I was wondering which hole they are mounting the arms onto the bulkheads. The drawings show a (A, B,) hole and I am not seeing the corresponding marking on the setup sheet, am i just missing it or maybe it just got overlooked.
Also do you have Rick's setup from invite, I did not see it posted as of today.
Congrats on your finish also, its great to see everyone excited about the car and doing so well with it. Mine will be comming soon.
Thanks,
Steve Curry
I was looking at Ryan and Kyle's setup's from the Reedy Race and I was wondering which hole they are mounting the arms onto the bulkheads. The drawings show a (A, B,) hole and I am not seeing the corresponding marking on the setup sheet, am i just missing it or maybe it just got overlooked.
Also do you have Rick's setup from invite, I did not see it posted as of today.
Congrats on your finish also, its great to see everyone excited about the car and doing so well with it. Mine will be comming soon.
Thanks,
Steve Curry
#2723
Tech Fanatic
I am thinking i will be picking one up tomorrow as well! Back to AE once again.
Last edited by tcmerf; 06-03-2007 at 11:16 PM.
#2724
I should have mine tomorrow... Thanks for all the info guys!
#2725
I think your rite Curry....Juho filled that part completely on his LRP Masters setup....but they are missing from the Reedy Race setups...
#2726
wait a sec....maybe there was only one hole in the bulkheads on the Reedy Race car?????? or the actual production car????
most likely not....but if so, that would explain it...
most likely not....but if so, that would explain it...
Last edited by STARSCREAM; 06-03-2007 at 09:34 PM.
#2727
Tech Elite
iTrader: (101)
I bet they were just overlooked, one hole is probably very common so far for the drivers, most likely the bottom hole. I'm sure by monday we will know.
Sean.....have you and I ever had the same type of car at the same time, I am thinking no. How's it going by the way.
Steve
Sean.....have you and I ever had the same type of car at the same time, I am thinking no. How's it going by the way.
Steve